ASTM C1737-22

Standard Guide for Evaluating Temperature Effects to Aerosol Foam Sealant During and After Dispensing

SIGNIFICANCE AND USE
5.1 This guide is not intended to measure the precise temperature range for dispensing and curing product under all the possible substrate and environmental factors but to provide a basis for benchmarking a foam sealant product under specific laboratory conditions.  
5.2 The product user is encouraged to evaluate each application and determine suitability for actual use.
SCOPE
1.1 This guide covers the general effects of temperature from the aerosol foam sealant (either polyurethane or latex types) under the use temperatures.  
1.2 The guide is intended to estimate the observed product dispensing characteristics and foam quality of aerosol foam dispensed or cured, or both, at specific temperatures and standard conditions.  
1.3 Such foam sealants are primarily intended to reduce air movement in and out of building enclosures.  
1.4 Currently two main foam sealant types are applicable to this standard: single component polyurethane and latex.  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 There are no other known test methods specific for measuring the product temperature range for aerosol foam sealant.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 31-Jul-2022
• ICS: 91.100.50 - Binders. Sealing materials
• Technical Committee: C24 - Building Seals and Sealants
• Drafting Committee: C24.61 - Aerosol Foam Sealants

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1737 − 22
Standard Guide for
Evaluating Temperature Effects to Aerosol Foam Sealant
1
During and After Dispensing
This standard is issued under the fixed designation C1737; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
1.1 This guide covers the general effects of temperature 2.1 ASTM Standards:
from the aerosol foam sealant (either polyurethane or latex C717 Terminology of Building Seals and Sealants
types) under the use temperatures. C1620 Specification for Aerosol Polyurethane and Aerosol
Latex Foam Sealants
1.2 The guide is intended to estimate the observed product
C1806 Test Method for Measuring the Flow Rate of Aerosol
dispensing characteristics and foam quality of aerosol foam
Foam Sealants
dispensed or cured, or both, at specific temperatures and
standard conditions.
3. Terminology
1.3 Such foam sealants are primarily intended to reduce air
3.1 Definitions of Terms Specific to This Standard:
movement in and out of building enclosures.
3.1.1 cure temperature—set temperature of the chamber
where the foam sealant cures. Also called the ambient air
1.4 Currently two main foam sealant types are applicable to
temperature for purposes of this guide.
this standard: single component polyurethane and latex.
3.1.2 flow rate—see Test Method C1806.
1.5 The values stated in SI units are to be regarded as
standard. No other units of measurement are included in this 3.1.3 friability—the property of a cured or semi-cured
standard.
foamed cellular material which permanently deforms and
crumbles after a light finger force is applied to the material
1.6 There are no other known test methods specific for
surface.
measuring the product temperature range for aerosol foam
sealant. 3.1.4 product temperature—temperature of the foam sealant
in its original container after 24 h at the manufacturer’s
1.7 This standard does not purport to address all of the
recommended test temperature.
safety concerns, if any, associated with its use. It is the
3.1.5 product use temperature—the aerosol can product
responsibility of the user of this standard to establish appro-
priate safety, health, and environmental practices and deter- temperature itself and the ambient air temperature during the
cure.
mine the applicability of regulatory limitations prior to use.
1.8 This international standard was developed in accor-
3.1.6 standard conditions—see Terminology in C717.
dance with internationally recognized principles on standard-
3.1.7 tack free time—see Specification C1620.
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom- 4. Summary of Guide
mendations issued by the World Trade Organization Technical
4.1 Procedure—Select the desired temperatures to measure.
Barriers to Trade (TBT) Committee.
A product for example could be tested at a product temperature
of 5 °C, and a cure temperature (ambient air temperature) of
0 °C. This comprises the product use temperature.
1
This guide is under the jurisdiction of ASTM Committee C24 on Building Seals
and Sealants and is the direct responsibility of Subcommittee C24.61 on Aerosol
2
Foam Sealants. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Aug. 1, 2022. Published September 2022. Originally contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
approved in 2010. Last previous edition approved in 2016 as C1737–16. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C1737-22. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1737 − 22
4.1.1 Specimens from a completely filled aerosol contain- Kraft Paper while the paper is in the curing test chamber. Close
er’s are dispensed at specified size and as bead segments. the door within 5 s of opening the curing chamber.
4.1.2 Product temperature is maintained at selected product
9.6 With an unopened separate foam sealant aerosol can
temperature prior to testing at the selected cure temperature
conditioned at desired product temperature, measure flow rate
(which may be the same or different than the product tempera-
in accordance with Test Method C1806.
ture).
9.6.1 Note the approximate flow rate time and quality of
4.1.3 Foam products are evaluated for flow rate, tack free
foam sealant flow relative to dispensing at 23ºC with 1 (lowest
time, friability, and skin and cell appearance as
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1737 − 16 C1737 − 22
Standard Guide for
Evaluating Temperature Effects to Aerosol Foam Sealant
1
During and After Dispensing
This standard is issued under the fixed designation C1737; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This guide covers the general effects of temperature during the use temperatures for from the aerosol foam sealant (either
polyurethane or latex types).types) under the use temperatures.
1.2 The guide is intended to estimate the observed product dispensing charactercharacteristics and foam quality of aerosol foam
dispensed or cured, or both, at specific temperatures and standard conditions.
1.3 Such foam sealants are used for a variety of end use applications primarily intended to reduce air movement in and out of
building enclosures.
1.4 Currently two main foam sealant types are applicable to this standard,standard: single component polyurethane and latex
types.latex.
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6 There are no other known test methods specific for measuring the product temperature range for aerosol foam sealant.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C717 Terminology of Building Seals and Sealants
C1620 Specification for Aerosol Polyurethane and Aerosol Latex Foam Sealants
C717C1806 Terminology of Building Seals and Test Method for Measuring the Flow Rate of Aerosol Foam Sealants
1
This guide is under the jurisdiction of ASTM Committee C24 on Building Seals and Sealants and is the direct responsibility of Subcommittee C24.61 on Aerosol Foam
Sealants.
Current edition approved July 15, 2016Aug. 1, 2022. Published August 2016September 2022. Originally approved in 2010. Last previous edition approved in 2016 as
C1737-10 (2016). –16. DOI: 10.1520/C1737–16.10.1520/C1737-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1737 − 22
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 cure temperature—set temperature of the chamber used for curing where the foam sealant. sealant cures. Also called the
ambient air temperature for purposes of this guide.
3.1.2 flow rate—see Test Method C1806.
3.1.3 friability—the property of a cured or semi cured semi-cured foamed cellular material which permanently deforms and
crumbles to a powder like consistency after a light finger force is applied to the material surface.
3.1.4 product temperature—temperature of the foam sealant in its original container after 24 h incubation.at the manufacturer’s
recommended test temperature.
3.1.5 product use temperature—one measurement from the outcome of this guide. The product use temperature is composed of
two metrics as defined above, that is, the product temperature the aerosol can product temperature itself and the ambient air
temperature during the cure.
3.1.6 standard conditions—see Terminology in C717.
3.1.7 tack free time—see Specification C1620.
3.1.6 A definition of the following term is found in Terminology C717: standard conditions.
4. Summary of Guide
4.1 Procedure—Select the desired temperatures to measure foam sealant specimens for “test product temperature” and “test-cure
temperature.” measure. A product for example could be tested at a product temperature of 5°C,5 °C, and a cur
...