ASTM B572-06(2011)
(Specification)Standard Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Rod
Standard Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Rod
SCOPE
1.1 This specification covers alloys UNS N06002, UNS N06230, UNS N12160, and UNS R30556* in the form of rod for heat resisting and general-corrosive service.
1.2 The following products are covered under this specification:
1.2.1 Rods 5/16to ¾ in. (7.94 to 19.05 mm) exclusive in diameter, hot or cold finished, solution-annealed, and pickled or mechanically descaled.
1.2.2 Rods ¾ to 3½ in. (19.05 to 88.9 mm) inclusive in diameter, hot or cold finished, solution annealed, ground, or turned.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B572 −06(Reapproved2011)
Standard Specification for
UNS N06002, UNS N06230, UNS N12160, and UNS R30556
1
Rod
This standard is issued under the fixed designation B572; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Check Analysis Limits for Nickel, Nickel Alloys and
2 Cobalt Alloys
1.1 This specification covers alloys UNS N06002, UNS
E8 Test Methods for Tension Testing of Metallic Materials
N06230, UNS N12160, and UNS R30556* in the form of rod
E29 Practice for Using Significant Digits in Test Data to
for heat resisting and general-corrosive service.
Determine Conformance with Specifications
1.2 The following products are covered under this specifi-
E55 Practice for Sampling Wrought Nonferrous Metals and
cation:
Alloys for Determination of Chemical Composition
5 3
1.2.1 Rods ⁄16 to ⁄4 in. (7.94 to 19.05 mm) exclusive in
E527 Practice for Numbering Metals and Alloys in the
diameter, hot or cold finished, solution-annealed, and pickled
Unified Numbering System (UNS)
or mechanically descaled.
E1473 Test Methods for Chemical Analysis of Nickel,
3 1
1.2.2 Rods ⁄4 to 3 ⁄2 in. (19.05 to 88.9 mm) inclusive in
Cobalt, and High-Temperature Alloys
diameter, hot or cold finished, solution annealed, ground, or
3. Terminology
turned.
3.1 Definitions of Terms Specific to This Standard:
1.3 The values stated in inch-pound units are to be regarded
3.1.1 rod, n—product of round solid section furnished in
as standard. The values given in parentheses are mathematical
straight lengths.
conversions to SI units that are provided for information only
and are not considered standard.
4. Ordering Information
1.4 This standard does not purport to address all of the
4.1 It is the responsibility of the purchaser to specify all
safety concerns, if any, associated with its use. It is the
requirements that are necessary for material ordered under this
responsibility of the user of this standard to become familiar
specification. Examples of such requirements include, but are
with all hazards including those identified in the appropriate
not limited to the following:
Material Safety Data Sheet (MSDS) for this product/material
4.1.1 Alloy,
as provided by the manufacturer, to establish appropriate
4.1.2 Dimensions—Nominal diameter and length. The
safety and health practices, and determine the applicability of
shortest useable multiple length should be specified (Table 1),
regulatory limitations prior to use.
4.1.3 Certification—State if certification or a report of test
results is required (Section 16).
2. Referenced Documents
4.1.4 Purchaser Inspection—State which tests or inspec-
3
2.1 ASTM Standards:
tions are to be witnessed (Section 13), and
B880 Specification for General Requirements for Chemical
4.1.5 Samples for Product (Check) Analysis—State whether
samples should be furnished (9.2.2).
5. Chemical Composition
1
This specification is under the jurisdiction of ASTM Committee B02 on
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
5.1 The material shall conform to the requirements as to
B02.07 on Refined Nickel and Cobalt and Their Alloys.
chemical composition prescribed in Table 2.
Current edition approved June 1, 2011. Published June 2011. Originally
approved in 1972. Last previous edition approved in 2006 as B572 - 06. DOI:
5.2 If a product (check) analysis is made by the purchaser,
10.1520/B0572-06R11.
the material shall conform to the requirements specified in
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi-
Table 2 subject to the permissible tolerances in Specification
cation SB-572 in Section II of that Code.
* NewdesignationestablishedinaccordancewithPracticeE527andSAEJ1086,
B880.
Practice for Numbering Metals and Alloys (UNS).
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or 6. Mechanical and Other Requirements
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
6.1 The mechanical properties of the material at room
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. temperature shall conform to those shown in Table 3.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B572−06(2011)
TABLE 1 Permissible Variations in Length of Rods
7.3 Machining Allowances—When the surfaces of finished
Random mill lengths 2 to 12 ft (610 to 3660 mm) long with not more material are to be machined, the following allowances are
than 25 weight % under 4 ft (1.22 m).
sugges
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.