ASTM A861-04(2008)

Standard Specification for High-Silicon Iron Pipe and Fittings

ABSTRACT
This specification covers high-silicon iron pipe and pipe fittings intended for corrosion-resistant service for both above- and below-grade construction. The castings shall be true to pattern, reasonable smooth, and free from defects that would make the castings unfit for the use for which they are intended. The material shall conform to the chemical composition requirements specified. All centrifugally cast high-silicon iron pipe shall be supplied in the as-cast condition. All other pipe and fittings shall be supplied in the stress-relieved condition; the stress relieving procedures are presented. Acid-proof joints for hub/plain-end pipe shall require the use of an acid-proof rope packing. No-hub pipe and fittings shall require a special acid resistant mechanical joint coupling. High-silicon iron pipe can be cut with either manual or hydraulic snap cutters. Hydrostatic testing shall be conducted on all castings.
SCOPE
1.1 This specification covers high-silicon iron pipe and pipe fittings intended for corrosion-resistant service for both above- and below-grade construction.
1.2 Pipe and pipe fittings shall be the no-hub (MJ) or the hub and plain end design.
1.3 Pipe and pipe fittings shall be of the sizes specified in and and or other sizes that shall be permitted to conform to the requirements given herein.
1.3.1 PipeNo-hub (MJ) (Fig. 1).

General Information

• Status: Historical
• Publication Date: 30-Sep-2008
• ICS: 23.040.10 - Iron and steel pipes
• ICS: 23.040.40 - Metal fittings
• Technical Committee: A04 - Iron Castings
• Drafting Committee: A04.12 - Pipes and Tubes

Relations

• Replaces: ASTM A861-04 - Standard Specification for High-Silicon Iron Pipe and Fittings
• Effective Date: 01-Oct-2008
• Replaced By: ASTM A861-04(2013) - Standard Specification for High-Silicon Iron Pipe and Fittings
• Effective Date: 01-May-2013

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A861 −04(Reapproved 2008)
Standard Specification for
1
High-Silicon Iron Pipe and Fittings
This standard is issued under the fixed designation A861; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
Figs.
Quarter Bends 2
1.1 This specification covers high-silicon iron pipe and pipe
Sixth Bends 3
fittings intended for corrosion-resistant service for both above- Return Bends 4
Double-Branch Quarter Bend 5
and below-grade construction.
Eighth Bends 6
Sixteenth Bends 7
1.2 The values stated in inch-pound units are to be regarded
Long-Sweep Quarter Bends 8
as standard. The values given in parentheses are mathematical
Sanitary Y Branches 9
conversions to SI units that are provided for information only
Double-Branch Sanitary Y 10
1
Sanitary Combination Y and ⁄8 Bend 11
and are not considered standard.
1
Double-Branch Sanitary Combination Y and ⁄8 Bend 12
1.3 Pipe and pipe fittings shall be the no-hub (MJ) or the Sanitary T Branches 13
Double Branch Sanitary T 14
hub and plain end design.
Sanitary Running Traps 15
Sanitary P Traps 16
1.4 Pipe and pipe fittings shall be of the sizes specified in
Swivel Trap P-Style Short 17
Table 1 and Table 2 and Figs. 1-71 or other sizes that shall be
Swivel Trap P-Style Long 18
permitted to conform to the requirements given herein.
Swivel Trap S-Style Long 19
Centrifugal Drum Trap P Swivel Type 20
1.4.1 Pipe:
Centrifugal Drum Trap S Swivel Type 21
1.4.1.1 No-hub (MJ) (Fig. 1):
Combination Cleanout and Test Tees 22
Coupling 23
Size (in.) Length (ft)
1
Pipe Plugs 24
1 ⁄2 7
Cleanout Plugs 25
27
No-hub (MJ)Adapter 26
37
47 Reducers—Increasers 27
Sink Outlet 28
1.4.1.2 Hub/Plain End (Fig. 35):
Sink Overflows 29
ThreadedAdapters 30
Size (in.) Length (ft)
Trap Cleanout Details 31
27
No-hub (MJ)Adapter 32
37
(MJ) (No-hub) to LeadAdapter 33
47
Floor Drains 34
67
87
1.4.3 Fitting (Hub/Plain End):
10 5
12 5 Figs.
Hub Plain End Pipe 35
15 5
Straight Tees 36
1.4.2 Fitting (No-hub) (MJ):
Sanitary T Branches 37
Sanitary Y Branches 38
Double-Branch Sanitary Tee 39
1
Double-Branch Sanitary Y 40
This specification is under the jurisdiction of ASTM Committee A04 on Iron
1
Double-Branch Sanitary Combination Y and ⁄8 Bend (T-Y) 41
Castings and is the direct responsibility of Subcommittee A04.12 on Pipes and
Short-Sweep Quarter Bends 42
Tubes.
Long-Sweep Quarter Bends 43
Current edition approved Oct. 1, 2008. Published November 2008. Originally
1
Sanitary Combination Y and ⁄8 Bend (T-Y) 44
approved in 1986. Last previous edition approved in 2004 as A861 – 04. DOI:
Quarter Bends 45
10.1520/A0861-04R08.
Copyright ©ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA19428-2959. United States
1

---------------------- Page: 1 ----------------------
A861−04 (2008)
TABLE 1 Tolerances for High-Silicon Iron Hub/Plain-End Pipe
NOTE 1—1 in. = 25.4 mm.
Size, in. Wall Thickness, in. ID Tolerance, in. OD Tolerance, in.
1 1 1
2± ⁄32 ± ⁄32 ± ⁄32
1 1 1
3± ⁄32 ± ⁄32 ± ⁄32
1 1 1
4± ⁄32 ± ⁄32 ± ⁄32
1 1 3
6± ⁄32 ± ⁄32 ± ⁄64
1 1 1
8± ⁄32 ± ⁄8 ± ⁄8
1 1 1
10 ± ⁄8 ± ⁄8 ± ⁄8
1 1 1
12 ± ⁄8 ± ⁄8 ± ⁄8
1 1 1
15 ± ⁄8 ± ⁄8 ± ⁄8
Stop Lug
Size, in. D, in. ID, in. OD, in.
Depth (P), in.
1 1 1 3 1
1 ⁄2 4 ⁄4 1 ⁄2 2 ⁄16 (2.19) 1 ⁄32
TABLE 2 Tolerances for High-Silicon Iron Fittings
1 5 1
24 ⁄2 22 ⁄8 (2.62) 1 ⁄32
1 3 1 1 5 3 1
2×1 ⁄2 4 ⁄16×4 ⁄2 2×1 ⁄2 2 ⁄8×2 ⁄16 1 ⁄32
NOTE 1—1 in. = 25.4 mm.
3 1
3 533 ⁄4 (3.75) 1 ⁄32
ID Tolerance, OD Tolerance, Stop Lug Depth 1 3 1
45 ⁄2 44 ⁄4 (4.75) 1 ⁄32
Size, in.
in. in. Tolerance, in.
1 1 1 1
1 ⁄2 ± ⁄16 ± ⁄16 ± ⁄16
NOTE 1—1 in. = 25.4 mm.
1 1 1 1 1
1 ⁄2×1 ⁄2 ± ⁄16 ± ⁄16 ± ⁄16
FIG. 2Quarter Bends
1 1 1
2± ⁄16 ± ⁄16 ± ⁄16
1 1 1 1
2×1 ⁄2 ± ⁄16 ± ⁄16 ± ⁄16
1 1 1
2×2 ± ⁄16 ± ⁄16 ± ⁄16
1 1 1
3± ⁄16 ± ⁄16 ± ⁄16
1 1 1 1
3×1 ⁄2 ± ⁄16 ± ⁄16 ± ⁄16
1 1 1
3×2 ± ⁄16 ± ⁄16 ± ⁄16
1 1 1
3×3 ± ⁄16 ± ⁄16 ± ⁄16
1 1 1
4± ⁄16 ± ⁄16 ± ⁄16
1 1 1 1
4×1 ⁄2 ± ⁄16 ± ⁄16 ± ⁄16
1 1 1
4×2 ± ⁄16 ± ⁄16 ± ⁄16
1 1 1
4×3 ± ⁄16 ± ⁄16 ± ⁄16
1 1 1
4×4 ± ⁄16 ± ⁄16 ± ⁄16
Stop Lug
Size, in. D, in. ID, in. OD, in.
Depth (P), in.
1 1 3 1
1 ⁄2 31 ⁄2 2 ⁄16 1 ⁄32
1 5 1
23 ⁄4 22 ⁄8 1 ⁄32
1 3 1
33 ⁄2 33 ⁄4 1 ⁄32
3 3 1
43 ⁄4 44 ⁄4 1 ⁄32
NOTE 1—1 in. = 25.4 mm.
FIG. 3Sixth Bends
Size, in. J, in. F, in. t, in.
1 3 5
1 ⁄2 2 ⁄16 (2.19) 84 ⁄16
11 5
22 ⁄16 (2.69) 84 ⁄16
49 5
33 ⁄64 (3.77) 84 ⁄16
49 5
44 ⁄64 (4.77) 84 ⁄16
Stop Lug
Size, C, D, F, R, ID, OD,
NOTE 1—1 in. = 25.4 mm.
Depth
in. in. in. in. in. in. in.
FIG. 1No-Hub Pipe (MJ)
(P), in.
1 3 1 3 1
1 ⁄2 4 2 5 ⁄32 2 1 ⁄2 2 ⁄16 1 ⁄32
3 11 3 5 1
2 4 ⁄4 2 5 ⁄16 2 ⁄8 2 2 ⁄8 1 ⁄32
Sixth Bends 46
Eighth Bends 47
NOTE 1—1 in. = 25.4 mm.
Sixteenth Bends 48
Sanita
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A861–02 Designation: A 861 – 04 (Reapproved 2008)
Standard Specification for
1
High-Silicon Iron Pipe and Fittings
This standard is issued under the fixed designation A 861; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers high-silicon iron pipe and pipe fittings intended for corrosion-resistant service for both above- and
below-grade construction.
1.2Pipe and pipe fittings shall be the no-hub (MJ) or the hub and plain end design.
1.3Pipe and pipe fittings shall be of the sizes specified in
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 Pipe and pipe fittings shall be the no-hub (MJ) or the hub and plain end design.
1.4 PipeandpipefittingsshallbeofthesizesspecifiedinTable1andTable2andFigs.1-71orothersizesthatshallbepermitted
to conform to the requirements given herein.
1.3.1
1.4.1 Pipe:
1.3.1.1
1.4.1.1 No-hub (MJ) (Fig. 1):
Size (in.) Length (ft)
1
1 ⁄2 7
27
37
47
1.3.1.2
1.4.1.2 Hub/Plain End (Fig. 35):
Size (in.) Length (ft)
27
37
47
67
87
10 5
12 5
15 5
1.3.2
1.4.2 Fitting (No-hub) (MJ):
Figs.
Quarter Bends 2
Sixth Bends 3
Return Bends 4
Double-Branch Quarter Bend 5
Eighth Bends 6
Sixteenth Bends 7
Long-Sweep Quarter Bends 8
Sanitary Y Branches 9
1
This specification is under the jurisdiction of ASTM Committee A04 on Iron Castings and is the direct responsibility of Subcommittee A04.12 on Pipes and Tubes.
Current edition approved July 10, 2002. Published August 2002. Originally published as A861–86. Last previous edition A861–01a.
Current edition approved Oct. 1, 2008. Published November 2008. Originally approved in 1986. Last previous edition approved in 2004 as A 861 – 04.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
A 861 – 04 (2008)
Double-Branch Sanitary Y 10
1
Sanitary Combination Y and ⁄8 Bend 11
1
Double-Branch Sanitary Combination Y and ⁄8 Bend 12
Sanitary T Branches 13
Double Branch Sanitary T 14
Sanitary Running Traps 15
Sanitary P Traps 16
Swivel Trap P-Style Short 17
Swivel Trap P-Style Long 18
Swivel Trap S-Style Long 19
Centrifugal Drum Trap P Swivel Type 20
Centrifugal Drum Trap S Swivel Type 21
Combination Cleanout and Test Tees 22
Coupling 23
Pipe Plugs 24
Cleanout Plugs 25
No-hub (MJ) Adapter 26
Reducers—Increasers 27
Sink Outlet 28
Sink Overflows 29
Threaded Adapters 30
Trap Cleanout Details 31
No-hub (MJ) Adapter 32
(MJ) (No-hub) to Lead Adapter 33
Floor Drains 34
1.3.3
1.4.3 Fitting (Hub/Plain End):
Figs.
Hub Plain End Pipe 35
Straight Tees 36
Sanitary T Branches 37
Sanitary Y Branches 38
Double-Branch Sanitary Tee 39
Double-Branch Sanitary Y 40
1
Double-Branch Sanitary Combination Y and ⁄8 Bend (T-Y) 41
Short-Sweep Quarter Bends 42
Long-Sweep Quarter Bends 43
1
Sanitary Combination Y and ⁄8 Bend (T-Y) 44
Quarter Bends 45
Sixth Bends 46
Eighth Bends 47
Sixteenth Bends 48
Sanitary Increasers 49
Hub Strainers 50
Sanitary Reducers 51
Double Hubs 52
Pipe Plugs 53
Cleanout Plugs 54
Adapter—Plain end to Split Flange 55
Adapter—Hub to-Split Flange 56
Combination Cleanout and Test Tees 57
Insertable Joints 58
Backwater Valves 59
Sanitary P Traps 60
Sanitary S Traps 61
Sanitary Running Traps 62
Floor Drains 63, 64, 65
Floor Drains 66
Floor Drains/Installation—Funnel Attachment 67, 68
Overflow 69
Sink Outlet 70
Detailed Cross Section of Cleanout 71
Chemical Composition Table 3
Transverse Bend Test Minimum Requirements Table 4
2. Referenced Documents
2
2.1 ASTM Standards:A438Test Method for Transverse Testing of Gray Cast Iron
A 518/A 518M Specification for Corrosion-Resistant High-Silicon Iron Castings
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
, Vol 01.02.volume information, refer to the standard’s Document Summary page on the ASTM website.
2

---------------------- Page: 2 ----------------------
A 861 – 04 (2008)
E 350 Test Methods for ChemicalAnalysis of Carbon Steel, Low-Al
...