iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D4956-09e1

(Specification)

Standard Specification for Retroreflective Sheeting for Traffic Control

Standard Specification for Retroreflective Sheeting for Traffic Control

SCOPE
1.1 This specification covers flexible, non-exposed glass bead lens and microprismatic, retroreflective sheeting designed for use on traffic control signs, delineators, barricades, and other devices.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Jul-2009
ICS
93.080.30 - Road equipment and installations
Technical Committee
D04 - Road and Paving Materials
Drafting Committee
D04.38 - Highway Traffic Control Materials
Current Stage
Ref Project

Relations

Replaces
ASTM D4956-09 - Standard Specification for Retroreflective Sheeting for Traffic Control
Effective Date
01-Aug-2009
Replaced By
ASTM D4956-11a - Standard Specification for Retroreflective Sheeting for Traffic Control
Effective Date
30-Mar-2011
Referred By
ASTM E3165-18 - Standard Test Method for Nighttime Retroreflected Chromaticity of Retroreflective Sheeting
Effective Date
01-Aug-2009
Referred By
ASTM E1709-16(2022) - Standard Test Method for Measurement of Retroreflective Signs Using a Portable Retroreflectometer at a 0.2 Degree Observation Angle
Effective Date
01-Aug-2009
Referred By
ASTM E2706-18 - Standard Practice for Equipment Technology and Operations for Mobile and Plant-Based Secure Destruction Safety Requirements
Effective Date
01-Aug-2009
Referred By
ASTM D8514/D8514M-23 - Standard Specification for Flexible, Retroreflective Sheeting for Use in High Visibility Vehicle Markings
Effective Date
01-Aug-2009

Buy Standard

ASTM D4956-09e1 - Standard Specification for Retroreflective Sheeting for Traffic ControlASTM D4956-09e1 - Standard Specification for Retroreflective Sheeting for Traffic Control
PreviousNext
Technical specification
ASTM D4956-09e1 - Standard Specification for Retroreflective Sheeting for Traffic Control
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM D4956-09e1 - Standard Specification for Retroreflective Sheeting for Traffic ControlREDLINE ASTM D4956-09e1 - Standard Specification for Retroreflective Sheeting for Traffic Control
PreviousNext
Technical specification
REDLINE ASTM D4956-09e1 - Standard Specification for Retroreflective Sheeting for Traffic Control
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: D4956 – 09
Standard Specification for
1
Retroreflective Sheeting for Traffic Control
This standard is issued under the fixed designation D4956; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
´ NOTE—Table 13 was editorially corrected in December 2009.
1. Scope E991 PracticeforColorMeasurementofFluorescentSpeci-
mens Using the One-Monochromator Method
1.1 This specification covers flexible, non-exposed glass
E1164 Practice for Obtaining Spectrometric Data for
beadlensandmicroprismatic,retroreflectivesheetingdesigned
Object-Color Evaluation
for use on traffic control signs, delineators, barricades, and
E1247 Practice for Detecting Fluorescence in Object-Color
other devices.
Specimens by Spectrophotometry
1.2 The values stated in inch-pound units are to be regarded
E1347 Test Method for Color and Color-Difference Mea-
as standard. The values given in parentheses are mathematical
surement by Tristimulus Colorimetry
conversions to SI units that are provided for information only
E1349 Test Method for Reflectance Factor and Color by
and are not considered standard.
Spectrophotometry Using Bidirectional (45°:0° or 0°:45°)
1.3 The following safety hazards caveat pertains only to the
Geometry
test methods portion, Section 7, of this specification. This
E2152 Practice for Computing the Colors of Fluorescent
standard does not purport to address all of the safety concerns,
Objects from Bispectral Photometric Data
if any, associated with its use. It is the responsibility of the user
E2153 Practice for Obtaining Bispectral Photometric Data
of this standard to establish appropriate safety and health
for Evaluation of Fluorescent Color
practices and determine the applicability of regulatory limita-
E2301 Test Method for Daytime Colorimetric Properties of
tions prior to use.
Fluorescent Retroreflective Sheeting and Marking Materi-
2. Referenced Documents als for High Visibility Traffic Control and Personal Safety
2
Applications Using 45°:Normal Geometry
2.1 ASTM Standards:
G7 PracticeforAtmosphericEnvironmentalExposureTest-
B209 Specification for Aluminum and Aluminum-Alloy
ing of Nonmetallic Materials
Sheet and Plate
G147 PracticeforConditioningandHandlingofNonmetal-
B209M Specification for Aluminum and Aluminum-Alloy
lic Materials for Natural and Artificial Weathering Tests
Sheet and Plate (Metric)
G151 Practice for Exposing Nonmetallic Materials in Ac-
B449 Specification for Chromates on Aluminum
celerated Test Devices that Use Laboratory Light Sources
E284 Terminology of Appearance
G152 Practice for Operating Open Flame CarbonArc Light
E308 Practice for Computing the Colors of Objects by
Apparatus for Exposure of Nonmetallic Materials
Using the CIE System
E808 Practice for Describing Retroreflection
3. Terminology
E810 Test Method for Coefficient of Retroreflection of
3.1 Definitions—Definitions of terms are as described in
Retroreflective Sheeting Utilizing the Coplanar Geometry
Terminology E284 and Practice E808.
E811 Practice for Measuring Colorimetric Characteristics
3.2 Definitions of Terms Specific to This Standard:
of Retroreflectors Under Nighttime Conditions
3.2.1 reboundable sheeting, n—retroreflective material in-
tended to be attached to flexible impact resistant plastic
1
This specification is under the jurisdiction ofASTM Committee D04 on Road
devices, such as traffic drum-like channelizing devices.
and Paving Materials and is the direct responsibility of Subcommittee D04.38 on
Highway Traffic Control Materials.
4. Classification
Current edition approved Aug. 1, 2009. Published August 2009. Originally
´1
approved in 1989. Last previous edition approved in 2007 as D4956–07 . DOI:
4.1 Retroreflective sheeting shall consist of a white or
10.1520/D4956-09.
colored sheeting having a smooth outer surface and that
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
essentially has the property of a retroreflector over its entire
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
´1
D4956 – 09
surface. There are nine types and five classes of retroreflective 4.2.8 Type VIII—A retroreflective sheeting typically manu-
sheeting. Types are determined by conformance to the retrore- facturedasanunmetalizedcubecornermicroprismaticre
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation:D4956–09 Designation: D4956 – 09
Standard Specification for
1
Retroreflective Sheeting for Traffic Control
This standard is issued under the fixed designation D4956; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
´ NOTE—Table 13 was editorially corrected in December 2009.
1. Scope
1.1 Thisspecificationcoversflexible,non-exposedglassbeadlensandmicroprismatic,retroreflectivesheetingdesignedforuse
on traffic control signs, delineators, barricades, and other devices.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 Thefollowingsafetyhazardscaveatpertainsonlytothetestmethodsportion,Section7,ofthisspecification. This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
B209 Specification for Aluminum and Aluminum-Alloy Sheet and Plate
B209M Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric)
B449 Specification for Chromates on Aluminum
E284 Terminology of Appearance
E308 Practice for Computing the Colors of Objects by Using the CIE System
E808 Practice for Describing Retroreflection
E810 Test Method for Coefficient of Retroreflection of Retroreflective Sheeting Utilizing the Coplanar Geometry
E811 Practice for Measuring Colorimetric Characteristics of Retroreflectors Under Nighttime Conditions
E991 Practice for Color Measurement of Fluorescent Specimens Using the One-Monochromator Method
E1164 Practice for Obtaining Spectrometric Data for Object-Color Evaluation
E1247 Practice for Detecting Fluorescence in Object-Color Specimens by Spectrophotometry
E1347 Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry
E1349 Test Method for Reflectance Factor and Color by Spectrophotometry Using Bidirectional (45:0 or 0:45) Geometry
E2152 Practice for Computing the Colors of Fluorescent Objects from Bispectral Photometric Data
E2153 Practice for Obtaining Bispectral Photometric Data for Evaluation of Fluorescent Color
E2301 Test Method for Daytime Colorimetric Properties of Fluorescent Retroreflective Sheeting and Marking Materials for
High Visibility Traffic Control and Personal Safety Applications Using 45:Normal Geometry
G7 Practice for Atmospheric Environmental Exposure Testing of Nonmetallic Materials
G147 Practice for Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests
G151 Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources
G152 Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials
3. Terminology
3.1 Definitions—Definitions of terms are as described in Terminology E284 and Practice E808.
3.2 Definitions of Terms Specific to This Standard:
1
ThisspecificationisunderthejurisdictionofASTMCommitteeD04onRoadandPavingMaterialsandisthedirectresponsibilityofSubcommitteeD04.38onHighway
Traffic Control Materials.
´1
Current edition approved Aug. 1, 2009. Published August 2009. Originally approved in 1989. Last previous edition approved in 2007 as D4956–07 . DOI:
10.1520/D4956-09.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
´1
D4956 – 09
3.2.1 reboundable sheeting, n—retroreflective material intended to be attached to flexible impact resistant plastic devices, such
as traffic drum-like channelizing devices.
4. Classification
4.1 Retroreflective sheeting shall consist of a white or colored sheeting having a smooth outer surface and that essentially has
the property of a retroreflector over its entire s
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D8514/D8514M-23(Specification)
Standard Specification for Flexible, Retroreflective Sheeting for Use in High Visibility Vehicle Markings

SCOPE
1.1 This specification covers flexible, retroreflective sheeting for use in high visibility markings to provide enhanced daytime and/or nighttime visibility for use on emergency response vehicles, utility vehicles, and similar vehicles.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    12 pages
    English language
    sale 15% off
ASTM
ASTM D7942-15(2023)(Specification)
Standard Specification for Thermoplastic Pavement Markings in Non Snow Plow Areas

ABSTRACT
This specification covers reflectorized thermoplastic based pavement striping material of the class that is applied to the road surface in a molten state by screed/extrusion or ribbon extrusion means. It deals with longitudinal applications in non snow plow areas, standard (non-profile) pavement marking applications, and applications on smooth asphalt or concrete surfaces. It does not include asphalt seal coat applications, which use large aggregate resulting in a very rough, open grade finish. This specification establishes requirements with respect to chemical composition and physical property of the thermoplastic pavement marking material, requirements for the optics that are used to reflectorize the thermoplastic pavement marking material after application, field performance requirements for the installed thermoplastic pavement markings, and material application requirements.
SCOPE
1.1 This specification covers a reflectorized thermoplastic-based pavement striping material of the class that is applied to the road surface in a molten state by screed/extrusion or ribbon extrusion means. Retroreflectivity of the pavement marking compound is achieved initially by surface application of retroreflective optics at the time of pavement marking application. Upon cooling to normal pavement temperature, the pavement marking material produces an adherent reflectorized stripe of specified thickness and width capable of resisting deformation by traffic. The pavement marking compound includes retroreflective optics (glass beads or composite optics, or both) that are incorporated into the material at the time of manufacture that provide retroreflective properties during the service life of the material.  
1.1.1 This specification is limited to:
1.1.1.1 Longitudinal applications in non snow plow areas,
1.1.1.2 Standard (non-profile) pavement marking applications, and
1.1.1.3 Applications on smooth asphalt or concrete surfaces. Asphalt seal coat applications, which use large aggregate resulting in a very rough, open grade finish, are excluded from this specification.  
1.1.2 This specification includes:
1.1.2.1 Compositional and physical property requirements of the thermoplastic pavement marking material,
1.1.2.2 Requirements for the optics that are used to reflectorize the thermoplastic pavement marking material after application,
1.1.2.3 Field performance requirements for the installed thermoplastic pavement markings, and
1.1.2.4 Material application requirements.  
1.2 The values stated in inch-pounds units are to be regarded as the standard except where noted in the document. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D4956-19(Specification)
Standard Specification for Retroreflective Sheeting for Traffic Control

SCOPE
1.1 This specification covers flexible, non-exposed glass-bead lens and microprismatic, retroreflective sheeting designed for use on traffic control signs, delineators, barricades, and other devices. This specification does not address inks, overlays, or other imaging methods that may be applied to retroreflective sheeting material to create traffic signs or other devices.  
1.2 Although this specification provides photometric requirements for retroreflective sheeting under evaluation, minimum performance requirements of in-service signs or other devices are outside the scope of this document.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    15 pages
    English language
    sale 15% off
  • Technical specification
    15 pages
    English language
    sale 15% off
ASTM
ASTM F2656/F2656M-23(Test Method)
Standard Test Method for Crash Testing of Vehicle Security Barriers

SIGNIFICANCE AND USE
5.1 This test method provides a structured procedure to establish a penetration rating for vehicle perimeter barriers subjected to a vehicle impact. Knowing the penetration rating helps to select an appropriate barrier for site-specific conditions around a facility.  
5.2 The barrier penetration rating does not imply that a barrier will perform as rated in all site conditions, approach routes, and topography. Also, only single-specimen tests at a specified impact location are required by this test method, and therefore, not all points of impact can be tested and validated for the penetration rating. Other impact locations may respond differently.
SCOPE
1.1 This test method provides a range of vehicle impact conditions, designations, and penetration performance levels. This will allow an agency to select passive perimeter barriers and active entry point barriers appropriate for use at facilities with a defined moving vehicle threat. Agencies may adopt and specify those condition designations and performance levels in this test method that satisfy their specific needs. Agencies may also assign certification ratings for active and passive perimeter barriers based on the tests and test methodologies described herein. Many test parameters are standardized to arrive at a common vehicle type and mass, and replication, and produce uniform rating designations.  
1.2 Compliance with these test procedures establishes a measure of performance but does not render any vehicle perimeter barrier invulnerable to vehicle penetration. Caution should be exercised in interpreting test findings and in extrapolating results to other than test conditions and to user site conditions. This standard does not confirm the performance of the test barrier in the user site conditions. While computer simulations are powerful tools that are useful in the development of new and improved barriers or in estimating performance under differing conditions, the analytical models and methods must be validated against physical test data. When performing a test, developers and users are encouraged to address specific or unusual user site conditions as needed.  
1.2.1 Often local terrain features, soil conditions, climate, or other items will dictate special needs at specific locations. Therefore, if user site conditions are likely to degrade a barrier’s performance, the agency in need of a vehicle perimeter barrier should require testing with the specific user site conditions replicated for full-scale crash testing or numerical simulations that explicitly represent the user site conditions and have demonstrated connection to the “as-tested” soil configuration. For example, if the user site conditions are expansive clays, one could obtain user site materials and provide those to the test lab for the full-scale crash test.  
1.3 Product/design certification under this test method only addresses the ability of the barrier to withstand the impact of the test vehicle. It does not represent an endorsement of the product/design or address its operational suitability.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.5 This test method is intended to replace all previous versions of the test method for current and future testing.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and to determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established ...

  • Standard
    23 pages
    English language
    sale 15% off
  • Standard
    23 pages
    English language
    sale 15% off
ASTM
ASTM D713-23(Practice)
Standard Practice for Conducting Road Service Tests on Fluid Traffic Marking Materials

SIGNIFICANCE AND USE
3.1 This practice is an accelerated evaluation of bead retention, retroreflectivity, daytime color, night time color, and wear characteristics of fluid traffic marking materials. It is used to determine the useful life of such markings in the field. The same procedures are applicable to evaluating longitudinal lines to determine service life.
SCOPE
1.1 This practice covers the determination of the relative service life of fluid traffic marking materials such as paint, thermoplastic, epoxy, and polyester products under actual road conditions using transverse test lines. Materials under test are applied under prescribed conditions and periodic observations are made using prescribed performance criteria.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D711-23(Test Method)
Standard Test Method for No-Pick-Up Time of Pavement Markings

SIGNIFICANCE AND USE
3.1 This test method serves as a laboratory control test. Types of pavement markings that can be tested with this method are waterborne traffic paint, solvent borne traffic paint, and some two component 100 % solids liquid pavement markings, such as epoxy and modified epoxy pavement markings. If wet film thickness, temperature, and humidity are controlled within the tolerances specified herein, this method can be useful for relative testing of pavement markings and potentially for qualification of pavement markings for field application in approved specifications. For improved repeatability and meaningful comparison of pavement markings samples being tested, consistent air flow over the pavement marking films during testing is important. The buyer and seller should agree upon the air flow conditions, whether it be static or carefully regulated air flow (see 4.6.1 and 4.6.2). Because of the many variables operative in the field application of pavement markings (for example, wet film thickness, air temperature, humidity, wind speed, pavement type (asphalt or concrete), film profile over pavement, pavement temperature, pavement porosity, pavement moisture content, and the presence or absence of direct sunlight during striping), a direct correlation between the results of this test and field applications is difficult to obtain. However, relative field performance can be predicted using this method if the testing protocol is adhered to. For testing of two component 100 % solids liquid pavement markings an application of drop on retroreflective optics are typically applied at a specified rate to the markings prior to testing. For these types of pavement markings the regulation of air flow is not necessary due to the drying mechanics of the product.
SCOPE
1.1 This test method covers a laboratory procedure for determining the no-pick-up time of pavement markings. The method uses a wheel consisting of a metal cylinder with rubber O-rings. The wheel is rolled down a ramp over a freshly applied pavement marking film repeatedly until there is no transfer of the marking material to the rubber rings. The elapsed time from pavement marking film application to point of no marking material transfer is the no-pick-up time. Key variables to be controlled during testing are wet film thickness, temperature, humidity, air flow, and use of retroreflective optics. This standard provides three options for the testing of the no-pick-up time for pavement markings. The first option, Method A, specifies controls for temperature, humidity, and air flow during testing; a second option, Method B, specifies controls for temperature and humidity during testing, and a third option, Method C, provides guidance for performing this with a drop on application of retroreflective optics such as glass beads, Waterborne and Solvent Borne pavement markings are typically tested using Procedure A or Procedure B, without the application of drop on retroreflective optics. Pavement markings that are two component 100 % solids are typically tested using Method C.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM D8514/D8514M-23(Specification)
Standard Specification for Flexible, Retroreflective Sheeting for Use in High Visibility Vehicle Markings

SCOPE
1.1 This specification covers flexible, retroreflective sheeting for use in high visibility markings to provide enhanced daytime and/or nighttime visibility for use on emergency response vehicles, utility vehicles, and similar vehicles.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    12 pages
    English language
    sale 15% off
ASTM
ASTM D7942-15(2023)(Specification)
Standard Specification for Thermoplastic Pavement Markings in Non Snow Plow Areas

ABSTRACT
This specification covers reflectorized thermoplastic based pavement striping material of the class that is applied to the road surface in a molten state by screed/extrusion or ribbon extrusion means. It deals with longitudinal applications in non snow plow areas, standard (non-profile) pavement marking applications, and applications on smooth asphalt or concrete surfaces. It does not include asphalt seal coat applications, which use large aggregate resulting in a very rough, open grade finish. This specification establishes requirements with respect to chemical composition and physical property of the thermoplastic pavement marking material, requirements for the optics that are used to reflectorize the thermoplastic pavement marking material after application, field performance requirements for the installed thermoplastic pavement markings, and material application requirements.
SCOPE
1.1 This specification covers a reflectorized thermoplastic-based pavement striping material of the class that is applied to the road surface in a molten state by screed/extrusion or ribbon extrusion means. Retroreflectivity of the pavement marking compound is achieved initially by surface application of retroreflective optics at the time of pavement marking application. Upon cooling to normal pavement temperature, the pavement marking material produces an adherent reflectorized stripe of specified thickness and width capable of resisting deformation by traffic. The pavement marking compound includes retroreflective optics (glass beads or composite optics, or both) that are incorporated into the material at the time of manufacture that provide retroreflective properties during the service life of the material.  
1.1.1 This specification is limited to:
1.1.1.1 Longitudinal applications in non snow plow areas,
1.1.1.2 Standard (non-profile) pavement marking applications, and
1.1.1.3 Applications on smooth asphalt or concrete surfaces. Asphalt seal coat applications, which use large aggregate resulting in a very rough, open grade finish, are excluded from this specification.  
1.1.2 This specification includes:
1.1.2.1 Compositional and physical property requirements of the thermoplastic pavement marking material,
1.1.2.2 Requirements for the optics that are used to reflectorize the thermoplastic pavement marking material after application,
1.1.2.3 Field performance requirements for the installed thermoplastic pavement markings, and
1.1.2.4 Material application requirements.  
1.2 The values stated in inch-pounds units are to be regarded as the standard except where noted in the document. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D7308-17(2022)(Practice)
Standard Practice for Sample Preparation of Thermoplastic Pavement Marking Materials

SIGNIFICANCE AND USE
5.1 This practice provides a standard procedure for the preparation of thermoplastic pavement marking material test specimens prior to testing for various properties as called for in the governing specification. Specimens that are prepared using this standard methodology yield test results that are consistent with the material from which it was sampled. Test results from specimens can be used to determine compliance of the thermoplastic pavement marking material to the specification. This practice can also be used by manufacturers of these materials to prepare specimens for testing to determine the uniformity of thermoplastic pavement marking materials from batch to batch.  
5.2 This practice does not address any issues related to specific testing of the thermoplastic pavement marking materials for any physical or chemical property.
SCOPE
1.1 This practice covers the proper preparation of test specimens of thermoplastic pavement marking materials obtained to ensure test results are representative of the material being tested.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D2792-17(2022)(Practice)
Standard Practice for Solvent and Fuel Resistance of Traffic Paint

SIGNIFICANCE AND USE
4.1 Traffic paints must have good resistance to motor oil and fuel drippings on the highway. This test method describes the procedure necessary to evaluate the resistance of traffic paint to reference test fluids in order to simulate this type of action.
SCOPE
1.1 This practice describes a laboratory procedure for determining the resistance of a dried film of traffic paint to the action of a specified hydrocarbon solvent or gasoline fuel test fluid.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off