ASTM B908-09
(Practice)Standard Practice for the Use of Color Codes for Zinc Casting Alloy Ingot
Standard Practice for the Use of Color Codes for Zinc Casting Alloy Ingot
SIGNIFICANCE AND USE
The purpose of these color codes is to allow for quick identification of ingot bundles or jumbo ingots of zinc casting alloys. Other than jumbo ingots, this standard is not intended to imply that each ingot will be color-coded but only that each ingot bundle be color coded.
Each ingot bundle or jumbo ingot shall be identified with the appropriate color code listed in Table 1.
The color will be applied as a stripe, or stripes, on two adjacent sides of the ingot bundle or jumbo ingot. The color stripes will be applied to include the ingot bundle foot.
When using multiple stripes, the colored stripes will be applied from left to right as indicated in Table 1.
In the absence of a written agreement to the contrary between the supplier and end user, the North American color code will be the standard for all North American transactions; for all other transactions the International Color Code will be used.
TABLE 1 Color Codes CommonUNSAASTM
StandardASTM
AlloyTraditionalColor Code North AmericaBInternational Alloy 3Z33521B240AG 40ACZamak 3NoneWhite/YellowD Alloy 7Z33522B240AG 40BCZamak 7BrownWhite/BrownE Alloy 5Z35530B240AC 41ACZamak 5BlackWhite/BlackD Alloy 2Z35540B240AC 43ACZamak 2GreenWhite/GreenD ZA-8Z35635B240ZA-8ZA-8BlueWhite/BlueD ZA-12Z35630B240ZA-12ZA-12OrangeWhite/OrangeD ZA-27Z35840B240ZA-27ZA-27PurpleWhite/PurpleD ACuZinc 5Z46540B892Zn-Cu5-AI3ACuZinc5FRedWhite/RedE V12Z33730B327V12V12PinkWhite/PinkE V12-5B327V12-5V12-5Pink/BlackWhite/Pink/Black Slush Casting Alloy AZ34510B792Slush Casting Alloy ASlush Casting Alloy ABlack/RedWhite/Black/RedE Slush Casting Alloy BZ30500B792Slush Casting Alloy BSlush Casting Alloy BBlack/OrangeWhite/Black/OrangeE Zinc Casting Alloy for Dies and Molds - AZ35543B793Die & Mold Alloy AKirksite AGreen/RedWhite/Green/RedE Zinc Casting Alloy for Dies and Molds - BZ35542B793Die & Mold Alloy BKirksite BGreen/BlackWhite/Green/BlackE
A UNS assignations were established in accordance with Practice E527. The last digit of a U...
SCOPE
1.1 This standard is published with the following objectives:
1.2 To establish standard color codes for the Zinc Die Casting and Foundry industry, and
1.3 To standardize the use and application of these color codes.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B908 − 09
StandardPractice for the
1
Use of Color Codes for Zinc Casting Alloy Ingot
This standard is issued under the fixed designation B908; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* B899 Terminology Relating to Non-ferrous Metals and Al-
loys
1.1 Thisstandardispublishedwiththefollowingobjectives:
E527 Practice for Numbering Metals and Alloys in the
1.2 To establish standard color codes for the Zinc Die
Unified Numbering System (UNS)
Casting and Foundry industry, and
2.3 ISO Standard:
3
1.3 To standardize the use and application of these color ISO 301 Zinc alloy ingots intended for casting, 1981-05-15
codes. 2.4 CEN Standard:
EN 1774 Zinc and zinc alloys—Alloys for foundry
1.4 This standard does not purport to address all of the
4
purposes—Ingot and liquid, September 1997
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to become familiar
3. Terminology
with all hazards including those identified in the appropriate
3.1 Terms shall be defined in accordance with Terminology
Material Safety Data Sheet (MSDS) for this product/material
B899.
as provided by the manufacturer, to establish appropriate
safety and health practices, and determine the applicability of
4. Significance and Use
regulatory limitations prior to use.
4.1 The purpose of these color codes is to allow for quick
identification of ingot bundles or jumbo ingots of zinc casting
2. Referenced Documents
alloys.Otherthanjumboingots,thisstandardisnotintendedto
2.1 The following documents of the issue in effect on date
imply that each ingot will be color-coded but only that each
of order acceptance form a part of this specification to the
ingot bundle be color coded.
extent referenced herein:
4.2 Each ingot bundle or jumbo ingot shall be identified
2
2.2 ASTM Standards:
with the appropriate color code listed in Table 1.
B240 Specification for Zinc and Zinc-Aluminum (ZA) Al-
4.3 The color will be applied as a stripe, or stripes, on two
loys in Ingot Form for Foundry and Die Castings
adjacent sides of the ingot bundle or jumbo ingot. The color
B275 Practice for Codification of Certain Nonferrous Metals
stripes will be applied to include the ingot bundle foot.
and Alloys, Cast and Wrought
B327 Specification for Master Alloys Used in Making Zinc
4.4 When using multiple stripes, the colored stripes will be
Die Casting Alloys
applied from left to right as indicated in Table 1.
B792 Specification for Zinc Alloys in Ingot Form for Slush
4.5 In the absence of a written agreement to the contrary
Casting
between the supplier and end user, the North American color
B793 Specification for Zinc Casting Alloy Ingot for Sheet
code will be the standard for all North American transactions;
Metal Forming Dies and Plastic Injection Molds
for all other transactions the International Color Code will be
B892 Specification forACuZinc5 (Zinc-Copper-Aluminum)
used.
Alloy in Ingot Form for Die Castings
5. Keywords
5.1 ACuZinc; ACuZinc5; color; color code; Kirksite; Kirk-
1
This practice is under the jurisdiction ofASTM Committee B02 on Nonferrous
site A; Kirksite B; non-ferrous metals; Zamak; Zamak 2;
Metals and Alloys and Alloys and is the direct responsibility of Subcommittee
Zamak 3; Zamak 5; Zamak 7; zinc; zinc alloys; zinc-aluminum
B02.04 on Zinc and Cadmium.
Current edition approved Oct. 1, 2009. Published October 2009. Originally alloys; zinc-copper-aluminum alloys
approved in 2000. Last previous edition approved in 2008 as B908 - 03 (2008).
DOI: 10.1520/B0908-09.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or “English Version” available from American National Standards Institute
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
4
Standards volume information, refer to the standard’s Document Summary page on “EnglishVersion” available from Global Engineering Documents, 15 Inverness
the ASTM website. Way, East Englewood, CO 80112-5704, http://global.ihs.com.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B908 − 09
TABLE 1 Color Codes
ASTM ASTM Color Code
A
Common UNS Traditional
B
Standard Alloy North America International
C D
Alloy 3 Z33521 B240 AG 40A Zamak 3 None White/Yellow
C E
Alloy 7 Z33522 B240 AG 40B Zamak 7 Brown White/Brown
C D
Alloy 5 Z35530 B240 AC 41A Zamak 5 Bl
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B908–03(Reapproved2008) Designation: B908 – 09
Standard Practice for the
1
Use of Color Codes for Zinc Casting Alloy Ingot
This standard is issued under the fixed designation B908; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This standard is published with the following objectives:
1.2 To establish standard color codes for the Zinc Die Casting and Foundry industry, and
1.3 To standardize the use and application of these color codes.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2.1 The following documents of the issue in effect on date of order acceptance form a part of this specification to the extent
referenced herein:
2
2.2 ASTM Standards:
B240 Specification for Zinc and Zinc-Aluminum (ZA) Alloys in Ingot Form for Foundry and Die Castings
B275 Practice for Codification of Certain Nonferrous Metals and Alloys, Cast and Wrought
B327 Specification for Master Alloys Used in Making Zinc Die Casting Alloys
B792 Specification for Zinc Alloys in Ingot Form for Slush Casting
B793 Specification for Zinc Casting Alloy Ingot for Sheet Metal Forming Dies and Plastic Injection Molds
B892 Specification for ACuZinc5 (Zinc-Copper-Aluminum) Alloy in Ingot Form for Die Castings
B899 Terminology Relating to Non-ferrous Metals and Alloys
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
2.3 ISO Standard:
3
ISO 301 Zinc alloy ingots intended for casting, 1981-05-15
2.4 CEN Standard:
4
EN 1774 Zinc and zinc alloys—Alloys for foundry purposes—Ingot and liquid, September 1997
3. Terminology
3.1 Terms shall be defined in accordance with Terminology B899.
4. Significance and Use
4.1 The purpose of these color codes is to allow for quick identification of ingot bundles or jumbo ingots of zinc casting alloys.
Other than jumbo ingots, this standard is not intended to imply that each ingot will be color-coded but only that each ingot bundle
be color coded.
4.2 Each ingot bundle or jumbo ingot shall be identified with the appropriate color code listed in Table 1.
4.3 The color will be applied as a stripe, or stripes, on two adjacent sides of the ingot bundle or jumbo ingot. The color stripes
will be applied to include the ingot bundle foot.
4.4 When using multiple stripes, the colored stripes will be applied from left to right as indicated in Table 1.
4.5 In the absence of a written agreement to the contrary between the supplier and end user, the NorthAmerican color code will
1
Precision and Bias This practice is under the jurisdiction of ASTM Committee B02 on Nonferrous Metals and Alloys and Alloys and is the direct responsibility of
Subcommittee B02.04 on Zinc and Cadmium.
Current edition approved MayOct. 1, 2008.2009. Published May 2008.October 2009. Originally approved in 2000. Last previous edition approved in 20032008 as
B908 - 03 (2008). DOI: 10.1520/B0908-03R08.10.1520/B0908-09.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
“English Version” available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
4
“English Version” available from Global Engineering Documents, 15 Inverness Way, East Englewood, CO 80112-5704, http://global.ihs.com.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B908 – 09
TABLE 1 Color Codes
Color Code
ASTM ASTM
A
Common UNS Traditional
B
Standard Alloy
North America International
C D
Alloy 3 Z33521 B240 AG 40A Zamak 3 None White/Yellow
C E
Alloy 7 Z33522 B240 AG 40B Zamak 7 Brown White/Br
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.