B10 - Reactive and Refractory Metals and Alloys

ABSTRACT
This specification covers the standard requirements for two grades of wrought hafnium and hafnium alloy strip, sheet, and plate: Grade R1 for nuclear applications and Grade R3 for commercial applications. The materials shall be made from ingots that are produced in a furnace by vacuum or plasma arc melting, vacuum electron-beam melting, a combination of these three methods, or other melting process conventionally used for reactive metals. The various mill products shall be formed with the conventional extrusion, forging, or rolling equipment normally found in primary ferrous and nonferrous plants. The sheet, strip, and plate shall either be hot-rolled or cold-rolled and shall be supplied in the recrystallized annealed condition. Grades R1 and R3 metal shall conform to the chemical composition requirements for aluminum, carbon, chromium, copper, hydrogen, iron, molybdenum, nickel, niobium, nitrogen, oxygen, silicon, tantalum, tin, titanium, tungsten, uranium, vanadium, zirconium, and hafnium as shall be determined by chemical analysis. Mechanical properties, which shall be determined by tension tests both in longitudinal and transverse direction, shall meet the prescribed tensile strength, yield strength, and elongation requirements. Corrosion testing in water shall also be performed to determine the corrosion resistance of the materials.
SCOPE
1.1 This specification covers two grades of wrought hafnium and hafnium alloy strip, sheet, and plate as follows:  
1.1.1 Grade R1 for nuclear applications, and  
1.1.2 Grade R3 for commercial applications.  
1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. SI values cannot be mixed with inch-pound values.  
1.3 The following precautionary caveat pertains only to the test method portions of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the requirements for 34 grades of titanium and titanium alloy seamless pipe intended for general corrosion resisting and elevated temperature service. Alloys may be supplied in the following conditions: Grades 5, 23, 24, 25, 29, 35, or 36 – annealed or aged; Grades 9, 18, 28, or 38 – cold-worked and stress-relieved or annealed; Grades 9, 18, 23, 28, or 29 – transformed-beta condition; and Grades 19, 20, or 21 – solution-treated or solution-treated and aged. The grades shall conform to the required chemical composition for nitrogen, carbon, hydrogen, iron, oxygen, aluminum, vanadium, tin, ruthenium, palladium, chromium, nickel, niobium, zirconium, silicon, and titanium. Chemical analysis and product analysis shall be performed. Mechanical requirements shall conform to the required room temperature values for tensile strength, yield strength, and elongation. The following shall also be performed: tension, flattening, bend, and hydrostatic tests.
SCOPE
1.1 This specification covers the requirements for 34 grades of titanium and titanium alloy seamless pipe intended for general corrosion resisting and elevated temperature service as follows:  
1.1.1 Grade 1—UNS R50250. Unalloyed titanium,  
1.1.2 Grade 2—UNS R50400. Unalloyed titanium,
1.1.2.1 Grade 2H—UNS R50400. Unalloyed titanium (Grade 2 with 58 ksi (400 MPa) minimum UTS),  
1.1.3 Grade 3—UNS R50550. Unalloyed titanium,  
1.1.4 Grade 5—UNS R56400. Titanium alloy (6 % aluminum, 4 % vanadium),  
1.1.5 Grade 7—UNS R52400. Unalloyed titanium plus 0.12 % to 0.25 % palladium,
1.1.5.1 Grade 7H—UNS R52400. Unalloyed titanium plus 0.12 % to 0.25 % palladium (Grade 7 with 58 ksi (400 MPa) minimum UTS),  
1.1.6 Grade 9—UNS R56320. Titanium alloy (3 % aluminum, 2.5 % vanadium),  
1.1.7 Grade 11—UNS R52250. Unalloyed titanium plus 0.12 % to 0.25 % palladium,  
1.1.8 Grade 12—UNS R53400. Titanium alloy (0.3 % molybdenum, 0.8 % nickel),  
1.1.9 Grade 13—UNS R53413. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.10 Grade 14—UNS R53414. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.11 Grade 15—UNS R53415. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.12 Grade 16—UNS R52402. Unalloyed titanium plus 0.04 % to 0.08 % palladium,
1.1.12.1 Grade 16H—UNS R52402. Unalloyed titanium plus 0.04 % to 0.08 % palladium (Grade 16 with 58 ksi (400 MPa) minimum UTS),  
1.1.13 Grade 17—UNS R52252. Unalloyed titanium plus 0.04 % to 0.08 % palladium,  
1.1.14 Grade 18—UNS R56322. Titanium alloy (3 % aluminum, 2.5 % vanadium plus 0.04 % to 0.08 % palladium),  
1.1.15 Grade 19—UNS R58640. Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum),  
1.1.16 Grade 20—UNS R58645. Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum) plus 0.04 % to 0.08 % palladium,  
1.1.17 Grade 21—UNS R58210. Titanium alloy (15 % molybdenum, 3 % aluminum, 2.7 % niobium, 0.25 % silicon),  
1.1.18 Grade 23—UNS R56407. Titanium alloy (6 % aluminum, 4 % vanadium, extra low interstitial, ELI),  
1.1.19 Grade 24—UNS R56405. Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.04 % to 0.08 % palladium,  
1.1.20 Grade 25—UNS R56403. Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.3 % to 0.8 % nickel and 0.04 % to 0.08 % palladium,  
1.1.21 Grade 26—UNS R52404. Unalloyed titanium plus 0.08 % to 0.14 % ruthenium,
1.1.21.1 Grade 26H—UNS R52404. Unalloyed titanium plus 0.08 % to 0.14 % ruthenium (Grade 26 with 58 ksi (400 MPa) minimum UTS),  
1.1.22 Grade 27—UNS R52254. Unalloyed titanium plus 0.08 % to 0.14 % ruthenium,  
1.1.23 Grade 28—UNS R56323. Titanium alloy (3 % aluminum, 2.5 % vanadium plus 0.08 % to 0.14 % ruthenium),  
1.1.24 Grade 29—UNS R56404. Titanium alloy (6 % aluminum, 4 % vanadium, extra low interstitial, ELI plus 0.08 % to 0.14 % ruthenium),  
1.1.25 Grade 33—UNS R53442. Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium...

ABSTRACT
This specification covers the requirements for 33 grades of titanium and titanium alloy welded pipe intended for general corrosion resisting and elevated temperature service. Welded pipe shall be made from annealed flat-rolled products by a welding process. Welded pipe may be further reduced by cold working or hot working. Grades 1, 2, 2 H, 7, 7H, 11,13, 14, 16, 16H, 17, 26H, 33, and 37 shall be furnished as welded or annealed. Grades 3, 12, 15, and 34 shall be furnished as annealed. Grade 5, 23, 24, 25, 35 shall be furnished as annealed, or aged. Grade 9, 18, 38 shall be furnished as annealed. Grade 19, 20, 21 shall be furnished as solution treated, or solution treated and aged. The materials shall conform to the required chemical composition for nitrogen, carbon, hydrogen, iron, oxygen, aluminum, vanadium, tin, ruthenium, palladium, cobalt, molybdenum, chromium, nickel, niobium, zirconium, silicon, and titanium. They shall also conform to the required mechanical propetries such as tensile strength, yield strength, and elongation.
SCOPE
1.1 This specification covers the requirements for 33 grades of titanium and titanium alloy welded pipe intended for general corrosion resisting and elevated temperature service as follows:  
1.1.1 Grade 1—UNS R50250. Unalloyed titanium,  
1.1.2 Grade 2—UNS R50400. Unalloyed titanium,
1.1.2.1 Grade 2H—UNS R50400. Unalloyed titanium (Grade 2 with 58 ksi (400 MPa) minimum UTS),  
1.1.3 Grade 3—UNS R50550. Unalloyed titanium,  
1.1.4 Grade 5—UNS R56400. Titanium alloy (6 % aluminum, 4 % vanadium),  
1.1.5 Grade 7—UNS R52400. Unalloyed titanium plus 0.12 % to 0.25 % palladium,
1.1.5.1 Grade 7H—UNS R52400. Unalloyed titanium plus 0.12 % to 0.25 % palladium (Grade 7 with 58 ksi (400 MPa) minimum UTS),  
1.1.6 Grade 9—UNS R56320. Titanium alloy (3 % aluminum, 2.5 % vanadium),  
1.1.7 Grade 11—UNS R52250. Unalloyed titanium plus 0.12 % to 0.25 % palladium,  
1.1.8 Grade 12—UNS R53400. Titanium alloy (0.3 % molybdenum, 0.8 % nickel),  
1.1.9 Grade 13—UNS R53413. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.10 Grade 14—UNS R53414. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.11 Grade 15—UNS R53415. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.12 Grade 16—UNS R52402. Unalloyed titanium plus 0.04 % to 0.08 % palladium,
1.1.12.1 Grade 16H—UNS R52402. Unalloyed titanium plus 0.04 % to 0.08 % palladium (Grade 16 with 58 ksi (400 MPa) minimum UTS),  
1.1.13 Grade 17—UNS R52252. Unalloyed titanium plus 0.04 % to 0.08 % palladium,  
1.1.14 Grade 18—UNS R56322. Titanium alloy (3 % aluminum, 2.5 % vanadium plus 0.04 % to 0.08 % palladium),  
1.1.15 Grade 19—UNS R58640. Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum),  
1.1.16 Grade 20—UNS R58645. Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum) plus 0.04 % to 0.08 % palladium,  
1.1.17 Grade 21—UNS R58210. Titanium alloy (15 % molybdenum, 3 % aluminum, 2.7 % niobium, 0.25 % silicon),  
1.1.18 Grade 23—UNS R56407. Titanium alloy (6 % aluminum, 4 % vanadium, extra low interstitial, ELI),  
1.1.19 Grade 24—UNS R56405. Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.04 % to 0.08 % palladium,  
1.1.20 Grade 25—UNS R56403. Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.3 % to 0.8 % nickel and 0.04 % to 0.08 % palladium,  
1.1.21 Grade 26—UNS R52404. Unalloyed titanium plus 0.08 % to 0.14 % ruthenium,
1.1.21.1 Grade 26H—UNS R52404. Unalloyed titanium plus 0.08 % to 0.14 % ruthenium (Grade 26 with 58 ksi (400 MPa) minimum UTS),  
1.1.22 Grade 27—UNS R52254. Unalloyed titanium plus 0.08 % to 0.14 % ruthenium,  
1.1.23 Grade 28—UNS R56323. Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.08 % to 0.14 % ruthenium,  
1.1.24 Grade 29—UNS R56404. Titanium alloy (6 % aluminum, 4 % vanadium with extra low interstitial elements (ELI)) plus 0.08 % to 0.14 % ruthenium,  
1.1.25 Grade 33—UNS R53442. Titaniu...

ABSTRACT
This specification covers fittings intended for general corrosion-resisting and elevated-temperature services, factory made from unalloyed titanium and titanium alloys. The titanium for welding fittings may consist of billets, bars, plates, seamless or welded pipe or tube that conforms to all the requirements for manufacturing process, testing, chemical composition, and mechanical properties. Forging, forming, or shaping operations may be performed by hammering, pressing, piercing, extruding, upsetting, rolling, bending, fusion welding, or by a combination of two or more of these operations. The titanium shall conform to the requirements as to prescribed chemical composition. Product analysis tolerances of aluminum, carbon, chromium, hydrogen, iron, molybdenum, nickel, niobium, nitrogen, oxygen, palladium, ruthenium, silicon, vanadium, zirconium, and some residuals shall be specified. The titanium shall conform to the requirements as to tensile properties prescribed in the specifications.
SCOPE
1.1 This specification2 covers fittings intended for general corrosion-resisting and elevated-temperature services, factory made from unalloyed titanium and titanium alloys. The term welding fittings applies to parts such as 45° and 90° elbows, 180° returns, caps, tees, reducers, lap-joint stub ends, and other types.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers wrought unalloyed tungsten plate, sheet, and foil. The various tungsten flat products covered by this specification shall be formed with the conventional rolling, forging, or extrusion equipment, normally found in primary ferrous and nonferrous plants. The ingot metal shall be consolidated employing either the powder metallurgy or vacuum-arc-casting process. The materials shall conform to the required chemical composition for carbon, oxygen, nitrogen, iron, nickel, and silicon. Plate, sheet, and foil shall be furnished in the following metallurgical condition: hot-rolled, stress relieved, and cold-rolled. The materials shall also conform to the required permissible variations in physical dimensions such as thickness, width, length, and flatness.
SCOPE
1.1 This specification covers wrought unalloyed tungsten plate, sheet, and foil.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the test method portions of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers three grades of zirconium and zirconium alloy bar and wire as grade R60702, unalloyed zirconium; grade R60704, zirconium-tin; and grade R60705, zirconium-niobium. The chemical composition; and mechanical properties requirements, such as tensile strength, yield strength, and elongation; are detailed.
SCOPE
1.1 This specification2 covers three grades of zirconium and zirconium alloy bar and wire.  
1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values.  
1.3 The following precautionary caveat pertains only to the test methods portions of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers for titanium and titanium alloy wire. The chemical composition; physical properties such as density; and mechanical properties such as tensile strength, elongation and hardness are detailed.
SCOPE
1.1 This specification covers titanium and titanium alloy wire as follows:  
1.1.1 Grade 1—UNS R50250. Unalloyed titanium,  
1.1.2 Grade 2—UNS R50400. Unalloyed titanium,
1.1.2.1 Grade 2H—UNS R50400. Unalloyed titanium (Grade 2 with 58 ksi (400 MPa) minimum UTS),  
1.1.3 Grade 3—UNS R50550. Unalloyed titanium,  
1.1.4 Grade 4—UNS R50700. Unalloyed titanium,  
1.1.5 Grade 5—UNS R56400. Titanium alloy (6 % aluminum, 4 % vanadium),  
1.1.6 Grade 6—UNS R54520. Titanium alloy (5 % aluminum, 2.5 % tin),  
1.1.7 Grade 7—UNS R52400. Unalloyed titanium plus 0.12 % to 0.25 % palladium,
1.1.7.1 Grade 7H—UNS R52400. Unalloyed titanium plus 0.12 % to 0.25 % palladium (Grade 7 with 58 ksi (400 MPa) minimum UTS),  
1.1.8 Grade 9—UNS R56320. Titanium alloy (3 % aluminum, 2.5 % vanadium),  
1.1.9 Grade 11—UNS R52250. Unalloyed titanium plus 0.12 % to 0.25 % palladium,  
1.1.10 Grade 12—UNS R53400. Titanium alloy (0.3 % molybdenum, 0.8 % nickel),  
1.1.11 Grade 13—UNS R53413. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.12 Grade 14—UNS R53414. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.13 Grade 15—UNS R53415. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.14 Grade 16—UNS R52402. Unalloyed titanium plus 0.04 % to 0.08 % palladium,
1.1.14.1 Grade 16H—UNS R52402. Unalloyed titanium plus 0.04 % to 0.08 % palladium (Grade 16 with 58 ksi (400 MPa) minimum UTS),  
1.1.15 Grade 17—UNS R52252. Unalloyed titanium plus 0.04 % to 0.08 % palladium,  
1.1.16 Grade 18—UNS R56322. Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.04 % to 0.08 % palladium,  
1.1.17 Grade 19—UNS R58640. Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum),  
1.1.18 Grade 20—UNS R58645. Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum) plus 0.04 % to 0.08 % palladium,  
1.1.19 Grade 21—UNS R58210. Titanium alloy (15 % molybdenum, 3 % aluminum, 2.7 % niobium, 0.25 % silicon),  
1.1.20 Grade 23—UNS R56407. Titanium alloy (6 % aluminum, 4 % vanadium with extra low interstitial elements, ELI),  
1.1.21 Grade 24—UNS R56405. Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.04 % to 0.08 % palladium,  
1.1.22 Grade 25—UNS R56403. Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.3 % to 0.8 % nickel and 0.04 % to 0.08 % palladium,  
1.1.23 Grade 26—UNS R52404. Unalloyed titanium plus 0.08 % to 0.14 % ruthenium,
1.1.23.1 Grade 26H—UNS R52404. Unalloyed titanium plus 0.08 % to 0.14 % ruthenium (Grade 26 with 58 ksi (400 MPa) minimum UTS),  
1.1.24 Grade 27—UNS R52254. Unalloyed titanium plus 0.08 % to 0.14 % ruthenium,  
1.1.25 Grade 28—UNS R56323. Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.08 % to 0.14 % ruthenium,  
1.1.26 Grade 29—UNS R56404. Titanium alloy (6 % aluminum, 4 % vanadium with extra low interstitial elements, ELI) plus 0.08 % to 0.14 % ruthenium,  
1.1.27 Grade 32—UNS R55111. Titanium alloy (5 % aluminum, 1 % tin, 1 % vanadium, 1 % zirconium, 0.8 % molybdenum),  
1.1.28 Grade 33—UNS R53442. Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),  
1.1.29 Grade 34—UNS R53445. Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),  
1.1.30 Grade 35—UNS R56340. Titanium alloy (4.5 % aluminum, 2 % molybdenum, 1.6 % vanadium, 0.5 % iron, 0.3 % silicon),  
1.1.31 Grade 36—UNS R58450. Titanium alloy (45 % niobium),  
1.1.32 Grade 37—UNS R52815. Titanium alloy (1.5 % aluminum),  
1.1.33 Grade 38—UNS R54250. Titanium alloy (4 % aluminum, 2.5 % vanadium, 1.5 % iron), and  
1.1.34 Grade 39—UNS R53390. Titanium alloy (0.25 % iron, 0.4 % silicon).
Note 1: H grade material is identical to the corresponding numeric grade (tha...

ABSTRACT
This specification covers the three grades of zirconium and zirconium alloy seamless and welded tubes. The tubes are furnished in three grades as Grade R60702 which is an unalloyed zirconium, Grade R60704 which is zirconium-tin alloy, and Grade R60705 which is zirconium-niobium alloy. Seamless tube shall be made by any seamless method. Welded tube shall be made from sheet or strip by an automatic arc-welding process or other method of welding. Filler metal shall not be used. The material shall conform to the required chemical compostion for zirconium, hafnium, iron, chromium, tin, hydrogen, nitrogen, carbon, niobium, and oxygen. The materials shall conform to the required tensile properties such as tensile strength, yield strength, and elongation.
SCOPE
1.1 This specification2 covers two grades of zirconium and zirconium alloy seamless and welded tubes.  
1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.  
1.3 The following precautionary caveat pertains only to the test methods portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers UNS R60001, R60802, R60804, and R60901 wrought zirconium and zirconium alloy bars, rods, and wires. All material grades covered should conform to the required chemical composition requirements. Elements that are intentionally added to the melt should be identified, analyzed and reported in the chemical analysis. The zirconium and zirconium alloys should be made from ingots produced by vacuum or plasma arc melting, vacuum electron-beam melting, a combination of the three methods, or other melting processes conventionally used for reactive metals. All processes should be performed in furnaces specifically for reactive metals. Mill products included in this specification should be formed with conventional extrusion, forging, or rolling equipment that is used in primary ferrous and nonferrous plants. The cold worked and annealed materials should be in fully annealed condition unless otherwise specified. Hot worked shapes should be furnished in not descaled, mechanically descaled, or mechanically descaled and pickled finish, while cold-worked shapes should be furnished in cold-worked, ground, or pickled finish.
SCOPE
1.1 This specification covers four grades of wrought zirconium and zirconium alloy bars, rod, and wire as follows:  
1.1.1 R60001—Unalloyed grade,  
1.1.2 R60802—Zirconium-Tin alloy (Zircaloy 2),  
1.1.3 R60804—Zirconium-Tin alloy (Zircaloy 4), and  
1.1.4 R60901—Zirconium-Niobium alloy.  
1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values.  
1.3 The following precautionary caveat pertains only to the test method portions of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers monolithic forms of unalloyed molybdenum.  
1.2 Grade 1 (UNS R03610)—Unalloyed monolithic forms molybdenum.  
1.3 Grade 2 (UNS R03610)—Unalloyed monolithic forms molybdenum.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers unalloyed molybdenum and molybdenum alloy bar, rod, and wire. The following materials are covered: molybdenum 360, molybdenum 361, molybdenum 363, molybdenum 364, molybdenum 365, and molybdenum 366. These materials shall be manufactured with conventional extrusion, forging, swaging, rolling, and drawing equipment. These shall materials be made by vacuum arc-melted or powder metallurgy methods. The chemical composition shall conform to the required contents of carbon, oxygen, nitrogen, iron, nickel, silicon, titanium, tungsten, zirconium, and molybdenum. Chemical analysis shall be done. Mechanical properties shall conform to the required tension properties: tensile strength, yield strength, elongation, and diamond pyramid hardness. Tension test shall also be done.
SCOPE
1.1 This specification covers unalloyed molybdenum and molybdenum alloy bar, rod, and wire as follows:  
1.1.1 Molybdenum 360—Unalloyed vacuum arc-cast molybdenum.  
1.1.2 Molybdenum 361—Unalloyed powder metallurgy molybdenum.  
1.1.3 Molybdenum Alloy 363—Vacuum arc-cast molybdenum–0.5 % titanium–0.1 % zirconium (TZM) alloy.  
1.1.4 Molybdenum Alloy 364—Powder metallurgy molybdenum–0.5 % titanium–0.1 % zirconium (TZM) alloy.  
1.1.5 Molybdenum 365—Unalloyed vacuum arc-cast molybdenum, low carbon.  
1.1.6 Molybdenum Alloy 366—Vacuum arc-cast molybdenum, 30 % tungsten alloy.  
1.2 This specification covers wire no smaller than 0.020 in. [0.51 mm] in diameter or of equivalent cross-sectional area. Specification F289 covers diameters up to 0.020 in. [0.51 mm].  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.4 The following precautionary caveat pertains only to the test method portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This guide covers a cleaning and descaling procedure useful to producers, users, and fabricators of titanium and titanium alloys for the removal of ordinary shop soils, oxides, and scales resulting from heat treatment operations and foreign substances present as surface contaminants. It is recommended that the materials shall be subjected to soil removal prior to heat treatment or application of acid treatment. Mechanical descaling methods such as sandblasting, shot blasting, and vapor blasting may be used to remove hot work scales and lubricants from titanium surfaces. Recommended post treatment of shot or abrasive blasted titanium surfaces may include acid pickling to ensure complete removal of surface contaminants. For chemically milled materials, salt bath conditioning may be required to remove the oxygen-contaminated layer. Acid etching treatment may be required following mechanical abrading or chemical conditioning of materials to completely clean the surface.
SCOPE
1.1 This guide covers a cleaning and descaling procedure useful to producers, users, and fabricators of titanium and titanium alloys for the removal of ordinary shop soils, oxides, and scales resulting from heat treatment operations and foreign substances present as surface contaminants.  
1.2 It is not intended that these procedures be mandatory for removal of any of the indicated soils but rather serve as a guide when titanium and titanium alloys are being processed in the wrought, cast, or fabricated form.  
1.3 It is the intent that these soils be removed prior to chemical milling, joining, plating, fabrication, and in any situation where foreign substances interfere with the corrosion resistance, stability, and quality of the finished product.  
1.4 Acid etching may be required following cleaning when the surface has an oxygen-contaminated layer or alpha case present.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the standard requirements for titanium and titanium alloy castings intended for general corrosion resistant and industrial applications. Materials for this specification shall be melted by conventional processes used for reactive metals such as consumable electrode and induction-slag, plasma arc, induction-skull, and electron beam melting processes. The materials shall undergo chemical, pour, and product analysis to determine the chemical composition which shall conform to the requirements for nitrogen, carbon, hydrogen, iron, oxygen, aluminum, vanadium, tin, ruthenium, palladium, cobalt, molybdenum, chromium, nickel, niobium, zirconium, silicon, and titanium. All castings shall be supplied in the as-cast condition except when post-weld heat treatment is required wherein it shall consist of a stress relief performed at certain temperatures. The surface of the castings shall be free of adhering mold material, scale, cracks, and hot tears as determined by visual inspection.
SCOPE
1.1 This specification covers titanium and titanium alloy castings intended for general corrosion resistant and industrial applications. as follows:  
1.1.1 Grade C-2—UNS R52550. Unalloyed titanium,  
1.1.2 Grade C-3—UNS R52551. Unalloyed titanium,  
1.1.3 Grade C-5—UNS R56409. Titanium alloy (6 % aluminum, 4 % vanadium),  
1.1.4 Grade C-7—UNS R52700. Unalloyed titanium plus 0.12 to 0.25 % palladium,  
1.1.5 Grade C-8—UNS R52703. Unalloyed titanium plus 0.12 to 0.25 % palladium,  
1.1.6 Grade C-9—UNS R56320. Titanium alloy (3 % aluminum, 2.5 % vanadium),  
1.1.7 Grade C-12—UNS R53400. Titanium alloy (0.3 % molybdenum, 0.8 % nickel),  
1.1.8 Grade C-16—UNS R52402. Unalloyed titanium plus 0.04 to 0.08 % palladium,  
1.1.9 Grade C-17—UNS R52702. Unalloyed titanium plus 0.04 to 0.08 % palladium, and  
1.1.10 Grade C-38—UNS R54250. Titanium alloy (4 % aluminum, 2.5 % vanadium, 1.5 % iron).  
1.2 This specification is intended for use of purchasers and/or producers of reactive metal castings for defining the requirements and assuring the properties of castings for unique corrosion-resistant applications, that is, not for commodity items which must meet all potential purchasers’ requirements.  
1.2.1 Users are advised to use the specification as a basis for obtaining castings which will meet minimum acceptance requirements established and revised by consensus of the members of the committee.  
1.2.2 User requirements considered more stringent may be met by the addition to the purchase order of one or more supplementary requirements, which may include, but are not limited to, those listed in Sections S1 through S8.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers seamless wrought zirconium-alloy tubes for nuclear reactor fuel cladding application. Two grades of reactor grade zirconium alloys are described. Tubes covered by this specification shall be made from ingots produced by multiple vacuum arc or electron beam melting in furnaces of a type conventionally used for reactive materials. The tubes shall conform to the requirements for chemical composition prescribed. Recrsytallisation annealed tubes shall conform to the requirements for mechanical properties at room temperature prescribed. The tension test shall be conducted. Yield strength and tension properties shall be determined. Burst testing, when specified, shall be performed at room temperature on finished tubing.
SCOPE
1.1 This specification covers seamless wrought zirconium-alloy tubes for nuclear fuel cladding application, in the outside diameter (OD) size range of 0.200 in. (5.1 mm) to 0.650 in. (16.5 mm) and wall thickness range of 0.010 in. (0.25 mm) to 0.035 in. (0.89 mm).  
1.2 Two grades of reactor grade zirconium alloys are described.  
1.2.1 The present UNS numbers designated for the two grades are given in Table 1.  
1.3 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values.  
1.4 The following precautionary caveat pertains only to the test method portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the six grades of zirconium and zirconium alloy ingots: Grade R60700, Grade R60702, Grade R60703, Grade R60704, Grade R60705, and Grade R60706. These materials shall be manufactured by electron beam, vacuum, or inert atmosphere melting in furnaces. The material shall form to the required chemical composition of zirconium, hafnium, iron, chromium, tin, hydrogen, nitrogen, carbon, niobium, and oxygen. Check analysis shall be performed. The following test methods shall be done: ultrasonic test and chemical test.
SCOPE
1.1 This specification covers six grades of zirconium ingots.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers zirconium and zirconium-alloy castings for general corrosion-resistant and industrial applications. Material for this specification shall be melted by conventional processes used for reactive metals. Typical methods include the consumable electrode and inductoslag melting processes. The material shall conform to the required chemical composition for zirconium, hafnium, iron, chromium, hydrogen, nitrogen, carbon, oxygen, phosphorus, tin, and niobium. Product analysis and heat treatment shall be performed on the material, and shall conform within the specified check analysis tolerances.
SCOPE
1.1 This specification covers zirconium and zirconium-alloy castings for general corrosion-resistant and industrial applications.  
1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of each other. Combining values from the two systems may result in nonconformance with this specification.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the standard requirements for wrought zirconium and zirconium alloy seamless and welded tubes for nuclear applications except for nuclear fuel cladding. Five grades of reactor grade zirconium and zirconium alloys with R60001, R60802, R60804, R60901, and R60904 UNS number designations are described. Material shall be made from ingots produced by vacuum arc melting, electron beam melting, or other melting process to be carried out in furnaces conventionally used for reactive metals. Seamless tubes may be made by billet extrusion with subsequent cold working, by drawing, swaging, or rocking, with intermediate annealing. Welded tubing shall be made from flat-rolled products by an automatic or semiautomatic welding process with no addition of filler metal and shall be cold reduced by drawing, swaging, or rocking. The products shall be in the recrystallized or cold-worked and stress-relieved conditions and shall be furnished by as-cold reducing, pickling, grounding, polishing, or end-saw cutting, machining, or shearing. Chemical and product analysis shall be performed on the materials which shall meet the chemical composition requirements for tin, iron, chromium, nickel, niobium, oxygen, and other impurity elements. The tensile properties shall be determined by a tensile test method and shall conform to the tensile strength, yield strength, and elongation limits. Steam and water corrosion tests and hydrostatic test shall be conducted to determine the acceptance criteria for corrosion and internal hydrostatic pressure, respectively. Burst properties, contractile strain ratio, grain size, and hydride orientation of the finished tubing shall also be determined.
SIGNIFICANCE AND USE
16.1 For the purpose of determining compliance with the specified limits of property requirements, an observed value or a calculated value shall be rounded in accordance with the rounding method of Practice E29.    
Test  
Rounded Units for Observed
or Calculated Value  
Chemical composition, tolerance
(when expressed in decimals)  
nearest unit in the last right hand place of figures of the specified limit  
Tensile strength and yield strength  
nearest 1000 psi (10 MPa)  
Elongation  
nearest 1 %
SCOPE
1.1 This specification covers seamless and welded wrought zirconium and zirconium-alloy tubes for nuclear application. Nuclear fuel cladding is covered in Specification B811.  
1.2 Five grades of reactor grade zirconium and zirconium alloys suitable for nuclear application are described.  
1.2.1 The present UNS numbers designated for the five grades are given in Table 1.  
1.3 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values.  
1.4 The following precautionary caveat pertains only to the test method portions of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers tantalum and tantalum alloy seamless and welded tubes of the following grades: UNS Grade R05400 which is unalloyed tantalum, powder-metallurgy consolidation, UNS Grade R05200 which is unalloyed tantalum, vacuum melted, UNS Grade R05252 which is tantalum with 2.5% tungsten alloy, vacuum melted, UNS Grade R05255 which is tantalum with 10% tungsten alloy, vacuum melted, and UNS Grade R05240 which is tantalum alloy with 60% tantalum, 40% columbium, electron-beam furnace or vacuum arc melted, or both. Seamless tube shall be made by any seamless method and the welded tube shall be made from flat-rolled product by an automatic or semiautomatic fusion welding process with no addition of filler metal. Mechanical properties such as ultimate tensile strength, yield strength, and elongation shall be determined by tensile, flare, and reverse flattening tests. Nondestructive tests such as hydrostatic test, pneumatic test, helium leak test, and ultrasonic test shall be done as well.
SIGNIFICANCE AND USE
12.1 For the purpose of determining compliance with the specified limits of property requirements, an observed value or a calculated value shall be rounded in accordance with the rounding method of Practice E29.
SCOPE
1.1 This specification covers tantalum and tantalum alloy seamless and welded tubes of the following grades:  
1.1.1 UNS Grade R05400—Unalloyed tantalum, powder-metallurgy consolidation,  
1.1.2 UNS Grade R05200—Unalloyed tantalum, vacuum melted,  
1.1.3 UNS Grade R05252—Tantalum + 2.5 % tungsten alloy, vacuum melted.  
1.1.4 UNS Grade R05255—Tantalum + 10 % tungsten alloy, vacuum melted.  
1.1.5 UNS Grade R05240—Tantalum alloy, 60 % tantalum, 40 % niobium, electron-beam furnace, vacuum arc melt, or both.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers 28 grades of seamless and welded titanium alloy tubes for surface condensers, evaporators, and heat exchangers. Seamless tube shall be made from hollow billet by any cold reducing or cold drawing process that will yield a product meeting the requirements prescribed. Welded tube shall be made from flat-rolled product by an automatic arc-welding process. The welded tube shall be sufficiently cold worked to final size in order to transform the cast weld microstructure into a typical equiaxed microstructure in the weld upon subsequent heat treatment. The titanium shall conform to the chemical requirements prescribed. The room temperature tensile properties of the tube in the condition normally supplied shall conform to the requirements prescribed. Tubing shall withstand, without cracking, flattening under a load applied gradually at room temperature until the distance between the load platens is not more than the required height. Welded tube shall be subjected to a reverse flattening test in accordance with supplement II of test methods and definitions A 370. Welded tubing shall be tested using both a non-destructive electromagnetic test and an ultrasonic test method. Seamless and welded/cold worked tubing shall be tested using an ultrasonic test method. Welded tubing shall be tested with a hydrostatic or pneumatic test method. Seamless tubing shall be tested with an electromagnetic or hydrostatic or pneumatic test method.
SCOPE
1.1 This specification2 covers the requirements for 28 grades of titanium and titanium alloy tubing intended for surface condensers, evaporators, and heat exchangers, as follows:  
1.1.1 Grade 1—UNS R50250. Unalloyed titanium,  
1.1.2 Grade 2—UNS R50400. Unalloyed titanium,
1.1.2.1 Grade 2H—UNS R50400. Unalloyed titanium (Grade 2 with 58 ksi (400 MPa) minimum UTS),  
1.1.3 Grade 3—UNS R50550. Unalloyed titanium,  
1.1.4 Grade 7—UNS R52400. Unalloyed titanium plus 0.12 to 0.25 % palladium,
1.1.4.1 Grade 7H—UNS R52400. Unalloyed titanium plus 0.12 to 0.25 % palladium (Grade 7 with 58 ksi (400 MPa) minimum UTS),  
1.1.5 Grade 9—UNS R56320. Titanium alloy (3 % aluminum, 2.5 % vanadium),  
1.1.6 Grade 11—UNS R52250. Unalloyed titanium plus 0.12 to 0.25 % palladium,  
1.1.7 Grade 12—UNS R53400. Titanium alloy (0.3 % molybdenum, 0.8 % nickel),  
1.1.8 Grade 13—UNS R53413. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.9 Grade 14—UNS R53414. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.10 Grade 15—UNS R53415. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.11 Grade 16—UNS R52402. Unalloyed titanium plus 0.04 to 0.08 % palladium,
1.1.11.1 Grade 16H—UNS R52402. Unalloyed titanium plus 0.04 to 0.08 % palladium (Grade 16 with 58 ksi (400 MPa) minimum UTS),  
1.1.12 Grade 17—UNS R52252. Unalloyed titanium plus 0.04 to 0.08 % palladium,  
1.1.13 Grade 18—UNS R56322. Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.04 to 0.08 % palladium,  
1.1.14 Grade 26—UNS R52404. Unalloyed titanium plus 0.08 to 0.14 % ruthenium,
1.1.14.1 Grade 26H—UNS R52404. Unalloyed titanium plus 0.08 to 0.14 % ruthenium (Grade 26 with 58 ksi (400 MPa) minimum UTS),  
1.1.15 Grade 27—UNS R52254. Unalloyed titanium plus 0.08 to 0.14 % ruthenium,  
1.1.16 Grade 28—UNS R56323. Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.08 to 0.14 % ruthenium,  
1.1.17 Grade 30—UNS R53530. Titanium alloy (0.3 % cobalt, 0.05 % palladium),  
1.1.18 Grade 31—UNS R53532. Titanium alloy (0.3 % cobalt, 0.05 % palladium),  
1.1.19 Grade 33—UNS R53442. Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),  
1.1.20 Grade 34—UNS R53445. Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),  
1.1.21 Grade 35—UNS R56340. Titanium alloy (4.5 % aluminum, 2 % molybdenum, 1.6 % vanadium, 0.5 % iron, 0.3 % silicon),  
1.1.22 Grade 36—UNS R58450. Titanium alloy (45 % niobium),  
1.1.23 Grade 37—UNS R5281...

ABSTRACT
This specification covers 39 grades of annealed titanium and titanium alloy forgings as Grade F-1, Grade F-2, Grade F-2H, Grade F-3, Grade F-4, Grade F-5, Grade F-6, Grade F-7, Grade F-7H, Grade F-9, Grade F-11, Grade F-12, Grade F-13, Grade F-14, Grade F-15, Grade F-16, Grade F-16H, Grade F-17, Grade F-18, Grade F-19 Grade F-20, Grade F-21, Grade F-23, Grade F-24, Grade F-25, Grade F-26, Grade F-26H, Grade F-27, Grade F-28, Grade F-29, Grade F-30, Grade F-31, Grade F-32, Grade F-33, Grade F-34, Grade F-35, Grade F-36, Grade F-37, and Grade F-38. The grades of titanium and titanium alloy metal covered by this specification shall conform to the requirements as to chemical composition prescribed. Forgings supplied under this specification shall conform to the requirements as to mechanical properties specified, as applicable, such as tensile strength, yield strength, and elongation. Nondestructive test requirements such as ultrasonic test, X-ray, or surface inspection shall be specified by the purchaser, if required.
SCOPE
1.1 This specification2 covers 39 grades of annealed titanium and titanium alloy forgings as follows:  
1.1.1 Grade F-1—UNS R50250. Unalloyed titanium,  
1.1.2 Grade F-2—UNS R50400. Unalloyed titanium,
1.1.2.1 Grade F-2H—UNS R50400. Unalloyed titanium (Grade 2 with 58 ksi (400 MPa) minimum UTS),  
1.1.3 Grade F-3—UNS R50550. Unalloyed titanium,  
1.1.4 Grade F-4—UNS R50700. Unalloyed titanium,  
1.1.5 Grade F-5—UNS R56400. Titanium alloy (6 % aluminum, 4 % vanadium),  
1.1.6 Grade F-6—UNS R54520. Titanium alloy (5 % aluminum, 2.5 % tin),  
1.1.7 Grade F-7—UNS R52400. Unalloyed titanium plus 0.12 to 0.25 % palladium,
1.1.7.1 Grade F-7H—UNS R52400. Unalloyed titanium plus 0.12 to 0.25 % palladium (Grade 7 with 58 ksi (400 MPa) minimum UTS),  
1.1.8 Grade F-9—UNS R56320. Titanium alloy (3 % aluminum, 2.5 % vanadium),  
1.1.9 Grade F-11—UNS R52250. Unalloyed titanium plus 0.12 to 0.25 % palladium,  
1.1.10 Grade F-12—UNS R53400. Titanium alloy (0.3 % molybdenum, 0.8 % nickel),  
1.1.11 Grade F-13—UNS R53413. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.12 Grade F-14—UNS R53414. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.13 Grade F-15—UNS R53415. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.14 Grade F-16—UNS R52402. Unalloyed titanium plus 0.04 to 0.08 % palladium,
1.1.14.1 Grade F-16H—UNS R52402. Unalloyed titanium plus 0.04 to 0.08 % palladium (Grade 16 with 58 ksi (400 MPa) minimum UTS),  
1.1.15 Grade F-17—UNS R52252. Unalloyed titanium plus 0.04 to 0.08 % palladium,  
1.1.16 Grade F-18—UNS R56322. Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.04 % to 0.08 % palladium,  
1.1.17 Grade F-19—UNS R58640. Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum),  
1.1.18 Grade F-20—UNS R58645. Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum) plus 0.04 to 0.08 % palladium,  
1.1.19 Grade F-21—UNS R58210. Titanium alloy (3 % aluminum, 2.7 % niobium, 15 % molybdenum, 0.25 % silicon),  
1.1.20 Grade F-23—UNS R56407. Titanium alloy (6 % aluminum, 4 % vanadium, extra low interstitials, ELI),  
1.1.21 Grade F-24—UNS R56405. Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.04 to 0.08 % palladium,  
1.1.22 Grade F-25—UNS R56403. Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.3 to 0.8 % nickel and 0.04 to 0.08 % palladium,  
1.1.23 Grade F-26—UNS R52404. Unalloyed titanium plus 0.08 to 0.14 % ruthenium,
1.1.23.1 Grade F-26H—UNS R52404. Unalloyed titanium plus 0.08 to 0.14 % ruthenium (Grade 26 with 58 ksi (400 MPa) minimum UTS),  
1.1.24 Grade F-27—UNS R52254. Unalloyed titanium plus 0.08 to 0.14 % ruthenium,  
1.1.25 Grade F-28—UNS R56323. Titanium alloy (3 % aluminum, 2.5 % vanadium plus 0.08 to 0.14 % ruthenium),  
1.1.26 Grade F-29—UNS R56404. Titanium alloy (6 % aluminum, 4 % vanadium, extra low interstitial, ELI plus 0.08 to 0.14 % ruthenium),  
1....

ABSTRACT
This specification covers hot- and cold-rolled zirconium and zirconium alloy sheet, strip, and plate.
SCOPE
1.1 This specification covers hot- and cold-rolled zirconium and zirconium alloy sheet, strip, and plate.  
1.2 One unalloyed and three alloys for use in nuclear applications are described.  
1.3 The products covered in this specification include the following forms and sizes:  
1.3.1 Sheet, 24 in. [600 mm] or more in width; under 0.187 in. [4.8 mm] in thickness,  
1.3.2 Strip, less than 24 in. [600 mm] in width; under 0.187 in. [4.8 mm] in thickness, and  
1.3.3 Plate, over 10 in. [250 mm] in width; 0.187 in. [4.8 mm] and over in thickness.
Note 1: Material over 0.187 in. [4.8 mm] in thickness and less than 10 in. [250 mm] wide is covered as bar in Specification B351/B351M.  
1.4 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values.  
1.5 The following precautionary caveat pertains only to the test method portions of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers annealed bars and grills made from titanium or its alloys. All material grades covered should conform to the required chemical composition requirements. Elements that are intentionally added to the melt should be identified, analyzed and reported in the chemical analysis. Specimens for tension tests should be machined and the tensile properties determined using a specified strain rate through the yield strength and at an increasing rate. Each annealed material may be furnished as either descaled, sandblasted, ground, or rough turned.
SCOPE
1.1 This specification2 covers annealed titanium and titanium alloy bars and billets as follows:  
1.1.1 Grade 1—UNS R50250. Unalloyed titanium,  
1.1.2 Grade 2—UNS R50400. Unalloyed titanium,
1.1.2.1 Grade 2H—UNS R50400. Unalloyed titanium (Grade 2 with 58 ksi [400 MPa] minimum UTS),  
1.1.3 Grade 3—UNS R50550. Unalloyed titanium,  
1.1.4 Grade 4—UNS R50700. Unalloyed titanium,  
1.1.5 Grade 5—UNS R56400. Titanium alloy (6 % aluminum, 4 % vanadium),  
1.1.6 Grade 6—UNS R54520. Titanium alloy (5 % aluminum, 2.5 % tin),  
1.1.7 Grade 7—UNS R52400. Unalloyed titanium plus 0.12 to 0.25 % palladium,
1.1.7.1 Grade 7H—UNS R52400. Unalloyed titanium plus 0.12 to 0.25 % palladium (Grade 7 with 58 ksi [400 MPa] minimum UTS),  
1.1.8 Grade 9—UNS R56320. Titanium alloy (3 % aluminum, 2.5 % vanadium),  
1.1.9 Grade 11—UNS R52250. Unalloyed titanium plus 0.12 to 0.25 % palladium,  
1.1.10 Grade 12—UNS R53400. Titanium alloy (0.3 % molybdenum, 0.8 % nickel),  
1.1.11 Grade 13—UNS R53413. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.12 Grade 14—UNS R53414. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.13 Grade 15—UNS R53415. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.14 Grade 16—UNS R52402. Unalloyed titanium plus 0.04 to 0.08 % palladium,
1.1.14.1 Grade 16H—UNS R52402. Unalloyed titanium plus 0.04 to 0.08 % palladiumm (Grade 16 with 58 ksi [400 MPa] minimum UTS),  
1.1.15 Grade 17—UNS R52252. Unalloyed titanium plus 0.04 to 0.08 % palladium,  
1.1.16 Grade 18—UNS R56322. Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.04 to 0.08 % palladium,  
1.1.17 Grade 19—UNS R58640. Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum),  
1.1.18 Grade 20—UNS R58645. Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum) plus 0.04 %–0.08 % palladium,  
1.1.19 Grade 21—UNS R58210. Titanium alloy (15 % molybdenum, 3 % aluminum, 2.7 % niobium, 0.25 % silicon),  
1.1.20 Grade 23—UNS R56407. Titanium alloy (6 % aluminum, 4 % vanadium with extra low interstitial elements, ELI),  
1.1.21 Grade 24—UNS R56405. Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.04 % to 0.08 % palladium,  
1.1.22 Grade 25—UNS R56403. Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.3 % to 0.8 % nickel and 0.04 % to 0.08 % palladium,  
1.1.23 Grade 26—UNS R52404. Unalloyed titanium plus 0.08 to 0.14 % ruthenium,
1.1.23.1 Grade 26H—UNS R52404. Unalloyed titanium plus 0.08 to 0.14 % ruthenium (Grade 26 with 58 ksi [400 MPa] minimum UTS),  
1.1.24 Grade 27—UNS R52254. Unalloyed titanium plus 0.08 to 0.14 % ruthenium,  
1.1.25 Grade 28—UNS R56323. Titanium alloy (3 % aluminum, 2.5 % vanadium plus 0.08–0.14 % ruthenium),  
1.1.26 Grade 29—UNS R56404. Titanium alloy (6 % aluminum, 4 % vanadium, extra low interstitial, ELI plus 0.08 to 0.14 % ruthenium),  
1.1.27 Grade 30—UNS R53530. Titanium alloy (0.3 % cobalt, 0.05 % palladium),  
1.1.28 Grade 31—UNS R53532. Titanium alloy (0.3 % cobalt, 0.05 % palladium),  
1.1.29 Grade 32—UNS R55111. Titanium alloy (5 % aluminum, 1 % tin, 1 % zirconium, 1 % vanadium, 0.8 % molybdenum),  
1.1.30 Grade 33—UNS R53442. Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),  
1.1.31 Grade 34—UNS R53445. Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),  
1.1.32...

ABSTRACT
This specification covers five grades of zirconium strip, sheet, and plate. These are low oxygen zirconium (Grade R60700), unalloyed zirconium (Grade R60702), zirconium-tin (Grade R60704), zirconium-niobium (Grade R60705), and zirconium-niobium (Grade R60706). The materials shall be made from ingots that are produced by vacuum or plasma arc melting, vacuum electron-beam melting, a combination of these three methods or other melting processes conventionally used for reactive metals. All processes to be done in furnaces usually used for reactive metals. The various mill products covered by this specification are formed with the conventional extrusion, forging, or rolling equipment normally found in primary ferrous and nonferrous plants. The strip, sheet, and plate shall be supplied in the recrystallized annealed condition unless otherwise specified in the purchase order. The materials shall be subjected to chemical analysis and tensile strength, yield strength, elongation, bend, and flatness tests.
SCOPE
1.1 This specification2 covers five grades of zirconium strip, sheet, and plate.  
1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values.  
1.3 The following precautionary caveat pertains only to the test method portions of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers one grade of virgin zirconium metal commonly designated as sponge because of its porous, sponge-like texture, but it may also take other forms such as chunklets. The one grade described is designated as Reactor Grade R60001, suitable for use in nuclear applications. The main characteristic of the reactor grade is its low nuclear cross section as achieved by removal of hafnium. Zirconium metal is usually prepared by reduction of zirconium tetrachloride, and gets its physical characteristics from the processes involved in production. These characteristics may be expected to vary greatly with manufacturing methods. Only virgin zirconium metal, in identified, uniform, well-mixed blends, shall be used. The zirconium metal shall conform to the requirements for chemical composition specified.
SCOPE
1.1 This specification covers one grade of virgin zirconium metal commonly designated as sponge because of its porous, sponge-like texture, but it may also take other forms such as chunklets, suitable for use in nuclear applications.  
1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers hot-, cold-, or both hot- and cold-rolled hafnium rods and wires in either one of two grades. All grades should be in the recrystallization annealed condition unless specified otherwise. The materials should be made from ingots produced by vacuum melting in an electron beam or consumable arc furnaces, or both, of a type conventionally used for reactive metals. Samples for chemical composition tests should be taken from the top, middle, and bottom of the ingots. The requirements for mechanical properties do not apply to wires. Corrosion tests shall be done in water. All rods should be furnished in mechanically descaled and pickled, centerless ground and pickled, or centerless ground, pickled, and oxidized surface finish, while wires should be furnished in either conditioned and pickled or conditioned, pickled, and oxidized surface finish.
SIGNIFICANCE AND USE
15.1 For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding methods of Practice E29.    
Property  
Rounded Unit for Observed
or Calculated Value  
Chemical composition, and tolerances (when expressed as decimals)  
nearest unit in the last right-hand place of figures of the specified limit  
Tensile strength and yield strength  
nearest 1000 psi (10 MPa)  
Elongation  
nearest 1 %
SCOPE
1.1 This specification covers hot- or cold-worked hafnium rod and wire.  
1.2 This specification contains two material grades, one specifically for nuclear applications (Grade R1) and one for commercial alloying applications (Grade R3).  
1.3 The products covered include the following:  
1.3.1 Rod 3/8 to 1 in. (9.5 to 25 mm) in diameter.  
1.3.2 Wire less than 3/8 in. (9.5 mm) in diameter.  
1.4 Unless a single unit is used, for example, corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. SI values cannot be mixed with inch-pound values.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers vacuum-melted zirconium and zirconium alloy ingots for nuclear application. Materials covered shall be produced by multiple vacuum arc melting, or electron beam melting, or other melting processes conventionally used for reactive metals. Unless otherwise specified, ingots shall be conditioned by machining or grinding or both to remove surface and subsurface defects detrimental to subsequent fabrication. The ingot shall conform to the chemical composition requirements prescribed. The ingots shall be analyzed for the alloying and impurity elements prescribed. Ingots shall be inspected ultrasonically using the prescribed methods. The test shall be conducted in accordance with practice E 114.
SIGNIFICANCE AND USE
10.1 For purposes of determining compliance with the specified limits for requirements of the properties listed in Table 1 and Table 2, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.
SCOPE
1.1 This specification covers vacuum-melted zirconium and zirconium alloy ingots for nuclear application.  
1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.  
1.3 The following precautionary caveat pertains only to the test method portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This practice covers a cleaning and de-scaling procedure useful to producers, users, and fabricators of zirconium and zirconium alloys for the removal of ordinary shop soils, oxides, and scales resulting from heat treatment operations and foreign substances present as surface contaminants. Grease, oil, and lubricants employed in machining, forming, and fabricating operations on zirconium and zirconium alloys should be removed by employing one of the methods or a combination of methods: alkaline or emulsion soak-type cleaners, ultrasonic cleaning, acetone, citrus based cleaners, or safety solvent immersion washing or vapor degreasing, or electrolytic alkaline cleaning system. Mechanical de-scaling methods such as sandblasting, shot blasting, and vapor blasting may be used to remove hot work scales and lubricants from zirconium surfaces if followed by thorough conditioning and cleaning. Aluminum oxide, silicon carbide, silica sand, zircon sand, and steel grit are acceptable media for mechanical de-scaling. Recommended post treatment of shot or abrasive blasted zirconium surfaces may include acid pickling to ensure complete removal of metallic iron, oxide, scale, and other surface contaminants. Visual inspection of material cleaned in accordance with this practice should show no evidence of paint, oil, grease, glass, graphite, lubricant, scale, abrasive, iron, or other forms of contamination.
SCOPE
1.1 This practice covers a cleaning and descaling procedure useful to producers, users, and fabricators of zirconium and zirconium alloys for the removal of ordinary shop soils, oxides, and scales resulting from heat treatment operations and foreign substances present as surface contaminants.  
1.2 It is not intended that these procedures become mandatory for removal of any of the indicated soils but rather serve as a guide when zirconium and zirconium alloys are being processed in the wrought, cast, or fabricated form.  
1.3 It is the intent that these soils be removed prior to chemical milling, joining, plating, welding, fabrication, and in any situation where foreign substances interfere with the corrosion resistance, stability, and quality of the finished product.  
1.4 Unless a single unit is used, for example, solution concentrations in g/l, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. SI values cannot be mixed with inch-pound values.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Sections 3 and 7.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers fittings, factory made from three grades of zirconium and zirconium alloys. The term welding fittings applies to butt-welding parts such as 45 and 90° elbows, 180° returns, caps, tees, reducers, lap-joint stub ends, and other types. The fittings are furnished in three grades as follows: Grade R60702 or PZ 2 which is unalloyed zirconium, Grade R60704 or PZ4 which is zirconium-tin, and Grade R60705 or PZ5 which is zirconium-niobium. Forging, forming, or shaping operations may be performed by hammering, pressing, piercing, extruding, upsetting, rolling, bending, fusion welding, machining, or by a combination of these operations. The forming procedure shall be so applied that it will not produce injurious defects in the fittings. Filler metal, when used, shall be the same grade as the base metal. The material shall conform to the requirements as to chemical composition and tensile properties specified.
SCOPE
1.1 This specification covers fittings, factory made from three grades of zirconium and zirconium alloys. The term welding fittings applies to butt-welding parts such as 45 and 90° elbows, 180° returns, caps, tees, reducers, lap-joint stub ends, and other types.  
1.2 The values stated in either inch-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers seamless and welded zirconium and zirconium alloy pipe. The pipe is furnished in three grades as follows; grade R60702- unalloyed zirconium, grade R60704- zirconium-tin alloy, and grade R60705- zirconium-niobium alloy. Seamless pipe shall be made from any seamless method that will yield a product meeting the requirements prescribed. Pipe containing welded seams or other joints made by welding shall comply with the given provisions. The pipe shall be furnished in the annealed or stress-relieved condition. The material shall conform to the requirements as to chemical composition prescribed. The material, as represented by the test specimens, shall conform to the tensile properties prescribed.
SCOPE
1.1 This specification2 covers three grades of seamless and welded zirconium pipe.  
1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values.  
1.3 The following precautionary caveat pertains only to the test methods portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers two grades (Grade R60702 and Grade R60703) of zirconium metal commonly designated as sponge or chunklets, but may also take other forms. This specification does not include crystal bar zirconium. This sponge is used in non-nuclear applications. Zirconium metal is usually prepared by reduction of zirconium tetrachloride, and it gets its physical characteristics from the processes involved in production. These characteristics may be expected to vary greatly with manufacturing methods. This specification, however, is not limited to metal prepared by reduction of tetrachloride or to material of any specific physical form. Only virgin zirconium metal, in identified, uniform, well-mixed blends, shall be supplied under this specification. The material shall conform to the chemical composition requirements for zirconium, hafnium, iron, chromium, hydrogen, nitrogen, carbon, and oxygen. The material shall be subjected to a number of chemical tests as required in this specification.
SCOPE
1.1 This specification covers two grades of zirconium metal commonly designated as sponge or chunklets, but may also take other forms. This specification does not include crystal bar zirconium. This sponge is used in non-nuclear applications.  
1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values.  
1.3 The following precautionary caveat pertains only to the test method portions of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers plate consisting of a base metal to which is bonded, integrally and continuously, on one or both sides a layer of one of the following: titanium, zirconium, tantalum, niobium, and their alloys. The material generally is intended for pressure vessel use. The cladding metal shall be bonded to the base metal by any cladding operation that will produce a clad product which will conform to the requirements of this specification. When the cladding operation does not affect the chemical composition of the cladding or base metal, or both, the chemical analysis, in accordance with cladding, or base metal specifications or both, may be performed prior to the cladding operation. All heat treatments shall be performed as needed in the cladding operation unless otherwise specified or agreed between the purchaser and the manufacturer. Mechanical testing of the base metal, in accordance with the base metal specification, may be performed prior to the cladding operation. The tensile properties shall be determined by a tension test on the base metal only in accordance with the testing requirements of the base metal specification. The specimen orientation, location with respect to thickness, and number of tests and retests shall be in accordance with the requirements of the base metal specification when tension, bend, and impact tests shall be performed. The product surfaces shall be free of excess imperfections and extraneous materials as determined by visual examination.
SCOPE
1.1 This specification covers plate consisting of a base metal to which is bonded, integrally and continuously, on one or both sides a layer of one of the following: titanium, zirconium, tantalum, niobium, and their alloys. The material generally is intended for pressure vessel use.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. The values in parentheses and in metric tables are provided for information only.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers annealed titanium and titanium alloy strip, sheet, and plate. The grades of titanium and titanium alloy metal covered by this specification shall have the chemical composition requirements of: nitrogen, carbon, hydrogen, iron, oxygen, aluminum, vanadium, tin, ruthenium, palladium, cobalt, molybdenum, chromium, nickel, niobium, zirconium, silicon, and titanium. For sheet and strip, the bend test specimen shall stand being bent cold through without fracture in the outside of the bent portion. Product analysis tolerances cover variations between laboratories in the measurement of chemical content of the specimen. In cutting samples for analysis, the operation should be carried out insofar as possible in a dust-free atmosphere because utmost care must be used in sampling titanium for chemical analysis due to its great affinity for elements such as oxygen, nitrogen, and hydrogen. The chemical analysis shall be conducted by the standard techniques normally utilized by the manufacturer and purchaser.
SCOPE
1.1 This specification2 covers annealed titanium and titanium alloy strip, sheet, and plate as follows:  
1.1.1 Grade 1—UNS R50250. Unalloyed titanium,  
1.1.2 Grade 2—UNS R50400. Unalloyed titanium,
1.1.2.1 Grade 2H—UNS R50400. Unalloyed titanium (Grade 2 with 58 ksi (400 MPa) minimum UTS),  
1.1.3 Grade 3—UNS R50550. Unalloyed titanium,  
1.1.4 Grade 4—UNS R50700. Unalloyed titanium,  
1.1.5 Grade 5—UNS R56400. Titanium alloy (6 % aluminum, 4 % vanadium),  
1.1.6 Grade 6—UNS R54520. Titanium alloy (5 % aluminum, 2.5 % tin),  
1.1.7 Grade 7—UNS R52400. Unalloyed titanium plus 0.12 to 0.25 % palladium,
1.1.7.1 Grade 7H—UNS R52400. Unalloyed titanium plus 0.12 to 0.25 % palladium (Grade 7 with 58 ksi (400 MPa) minimum UTS),  
1.1.8 Grade 9—UNS R56320. Titanium alloy (3.0 % aluminum, 2.5 % vanadium),  
1.1.9 Grade 11—UNS R52250. Unalloyed titanium plus 0.12 to 0.25 % palladium,  
1.1.10 Grade 12—UNS R53400. Titanium alloy (0.3 % molybdenum, 0.8 % nickel),  
1.1.11 Grade 13—UNS R53413. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.12 Grade 14—UNS R53414. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.13 Grade 15—UNS R53415. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.14 Grade 16—UNS R52402. Unalloyed titanium plus 0.04 to 0.08 % palladium,
1.1.14.1 Grade 16H—UNS R52402. Unalloyed titanium plus 0.04 to 0.08 % palladium (Grade 16 with 58 ksi (400 MPa) minimum UTS),  
1.1.15 Grade 17—UNS R52252. Unalloyed titanium plus 0.04 to 0.08 % palladium,  
1.1.16 Grade 18—UNS R56322. Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.04 to 0.08 % palladium,  
1.1.17 Grade 19—UNS R58640. Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum),  
1.1.18 Grade 20—UNS R58645. Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum) plus 0.04 % to 0.08 % palladium,  
1.1.19 Grade 21—UNS R58210. Titanium alloy (15 % molybdenum, 3 % aluminum, 2.7 % niobium, 0.25 % silicon),  
1.1.20 Grade 23—UNS R56407. Titanium alloy (6 % aluminum, 4 % vanadium with extra low interstitial elements, ELI),  
1.1.21 Grade 24—UNS R56405. Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.04 % to 0.08 % palladium,  
1.1.22 Grade 25—UNS R56403. Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.3 % to 0.8 % nickel and 0.04 % to 0.08 % palladium,  
1.1.23 Grade 26—UNS R52404. Unalloyed titanium plus 0.08 to 0.14 % ruthenium,
1.1.23.1 Grade 26H—UNS R52404. Unalloyed titanium plus 0.08 to 0.14 % ruthenium (Grade 26 with 58 ksi (400 MPa) minimum UTS),  
1.1.24 Grade 27—UNS R52254. Unalloyed titanium plus 0.08 to 0.14 % ruthenium,  
1.1.25 Grade 28—UNS R56323. Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.08 to 0.14 % ruthenium,  
1.1.26 Grade 29—UNS R56404. Titanium alloy (6 % aluminum, 4 % vanadium with extra low interstitial elements, ELI) plus 0.08 to 0.14 % ruthenium,  
1.1.27 Grade 30—UNS R5...

ABSTRACT
This specification establishes the requirements for four classes of machinable, high-density tungsten base metal produced by consolidating metal powder mixtures, the composition of which is mainly tungsten. This material specification may be used for bare parts or for parts that may be coated with other materials for protection against corrosion and abrasion; intended for uses such as weights or counter-balances in static or dynamic balancing, high-speed rotating inertia members, radiation shielding, hypervelocity impact, and vibration-damping applications. The chemical; physical properties, such as microstructure and machinability; mechanical properties, such as tensile strength, yield strength, elongation, and hardness; and composition requirements, such as density; are detailed.
SCOPE
1.1 This specification covers the requirements for four classes of machinable, high-density tungsten base metal produced by consolidating metal powder mixtures, the composition of which is mainly tungsten. This material specification may be used for bare parts or for parts that may be coated with other materials for protection against corrosion and abrasion.  
1.2 This specification describes physical, mechanical, and microstructural testing of a material lot based on the use of test coupons, not actual parts. Sintered properties typically vary both with part size and sampling location within a given part. Results obtained from coupon testing may therefore differ from the properties of a specific location in a larger part.  
1.3 Intended Use—Parts made from this material are intended for uses such as weights or counter-balances in static or dynamic balancing, high-speed rotating inertia members, radiation shielding, hypervelocity impact, and vibration-damping applications. In selecting the appropriate alloy for a given application, it is important to note that as the tungsten content of the alloy is increased, stiffness, radiation attenuation, and density increase with an accompanying decrease in attainable ductility.  
1.4 Special Applications—For particular applications, properties or requirements other than those specified in Sections 5, 6, and 7 of this specification may be important. These alloys may contain elements which make them weakly ferromagnetic. Where freedom from magnetic response is required, this should be specified in the purchase order. Class 4 is not available in a non-magnetic grade. For purposes of this specification, non-magnetic material is defined as material having a maximum magnetic permeability of 1.05 (see Test Method A342). Also for special applications involving large sections, methods for determining internal quality, such as mechanical testing of specimens excised from these larger sections or suitable nondestructive tests may be applied. If such part property data are required, an additional part-specific test program shall be specified in the purchase order.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers titanium alloy bars with surface deformations and 90-degree anchorage hooks for use as near surface mounts for flexural and shear strengthening of concrete beams. The product can be furnished with or without anchorage hooks as specified by the purchaser. If supplied without hooks, the hooks shall be bent on-site prior to installation, as this method requires two 90-degree anchorage hooks.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers titanium and titanium alloy ingots. The chemical requirements and permissible variations in product analysis are specified. This standard does not claim to address all of the safety concerns, if any, associated with its use.
SCOPE
1.1 This specification covers titanium and titanium alloy ingots as follows:  
1.1.1 Grade 1—UNS R50250. Unalloyed titanium,  
1.1.2 Grade 2—UNS R50400. Unalloyed titanium,  
1.1.3 Grade 3—UNS R50550. Unalloyed titanium,  
1.1.4 Grade 4—UNS R50700. Unalloyed titanium,  
1.1.5 Grade 5—UNS R56400. Titanium alloy (6 % aluminum, 4 % vanadium),  
1.1.6 Grade 6—UNS R54520. Titanium alloy (5 % aluminum, 2.5 % tin),  
1.1.7 Grade 7—UNS R52400. Unalloyed titanium plus 0.12 to 0.25 % palladium,  
1.1.8 Grade 9—UNS R56320. Titanium alloy (3 % aluminum, 2.5 % vanadium),  
1.1.9 Grade 11—UNS R52250. Unalloyed titanium plus 0.12 to 0.25 % palladium,  
1.1.10 Grade 12—UNS R53400. Titanium alloy (0.3 % molybdenum, 0.8 % nickel),  
1.1.11 Grade 13—UNS R53413. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.12 Grade 14—UNS R53414. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.13 Grade 15—UNS R53415. Titanium alloy (0.5 % nickel, 0.05 % ruthenium),  
1.1.14 Grade 16—UNS R52402. Unalloyed titanium plus 0.04 to 0.08 % palladium,  
1.1.15 Grade 17—UNS R52252. Unalloyed titanium plus 0.04 to 0.08 % palladium,  
1.1.16 Grade 18—UNS R56322. Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.04 to 0.08 % palladium,  
1.1.17 Grade 19—UNS R58640. Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum),  
1.1.18 Grade 20—UNS R58645. Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum) plus 0.04 to 0.08 % palladium,  
1.1.19 Grade 21—UNS R58210. Titanium alloy (15 % molybdenum, 3 % aluminum, 2.7 % niobium, 0.25 % silicon),  
1.1.20 Grade 23—UNS R56407. Titanium alloy (6 % aluminum, 4 % vanadium with extra low interstitials, ELI),  
1.1.21 Grade 24—UNS R56405. Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.4 to 0.8 % palladium,  
1.1.22 Grade 25—UNS R56403. Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.3 to 0.8 % nickel and 0.04 to 0.08 % palladium,  
1.1.23 Grade 26—UNS R56404. Unalloyed titanium plus 0.08 to 0.14 % ruthenium,  
1.1.24 Grade 27—UNS R52254. Unalloyed titanium plus 0.08 to 0.14 % ruthenium,  
1.1.25 Grade 28—UNS R56323. Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.08 to 0.14 % ruthenium,  
1.1.26 Grade 29—UNS R56404. Titanium alloy (6 % aluminum, 4 % vanadium, extra low interstitial elements, ELI) plus 0.08 to 0.14 % ruthenium,  
1.1.27 Grade 30—UNS R53530. Titanium alloy (0.3 % cobalt, 0.05 % palladium),  
1.1.28 Grade 31—UNS R53532. Titanium alloy (0.3 % cobalt, 0.05 % palladium),  
1.1.29 Grade 32—UNS R55111. Titanium alloy (5 % aluminum, 1 % tin, 1 % zirconium, 1 % vanadium, 0.8 % molybdenum),  
1.1.30 Grade 33—UNS R53442. Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),  
1.1.31 Grade 34—UNS R53445. Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),  
1.1.32 Grade 35—UNS R56340. Titanium alloy (4.5 % aluminum, 2 % molybdenum, 1.6 % vanadium, 0.5 % iron, 0.3 % silicon),  
1.1.33 Grade 36—UNS R58450. Titanium alloy (45 % niobium),  
1.1.34 Grade 37—UNS R52815. Titanium alloy (1.5 % aluminum),  
1.1.35 Grade 38—UNS R54250. Titanium alloy (4 % aluminum, 2.5 % vanadium, 1.5 % iron), and  
1.1.36 Grade 39—UNS R53390. Titanium alloy (0.25 % iron, 0.4 % silicon).  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 The following caveat pertains only to the test method portions of this speci...

ABSTRACT
This specification covers unalloyed molybdenum and molybdenum alloy plate, sheet, strip, and foil as follows: Molybdenum 360; Molybdenum 361; Molybdenum Alloy 363; Molybdenum Alloy 364; Molybdenum 365; and Molybdenum Alloy 366. The various molybdenum mill products covered by this specification shall be formed with the conventional extrusion, forging, or rolling equipment normally found in primary ferrous and nonferrous plants. The ingot metal for Molybdenum 360 and 365 and Molybdenum Alloys 363 and 366 is vacuum arc-melted in furnaces of a type suitable for reactive, refractory metals. For Molybdenum 361 and Molybdenum Alloy 364, the metal is consolidated by powder metallurgy methods. The molybdenum and molybdenum alloy ingots and billets for conversion to finished products covered by this specification shall conform to the chemical composition requirements for carbon, oxygen, nitrogen, iron, nickel, silicon, titanium, tungsten, zirconium, and molybdenum. The material shall conform to the mechanical property requirements for tensile strength, yield strength, elongation, and minimum bend radius.
SCOPE
1.1 This specification covers unalloyed molybdenum and molybdenum alloy plate, sheet, strip, foil, and ribbon as follows:  
1.1.1 Molybdenum 360—Unalloyed vacuum arc-cast molybdenum.  
1.1.2 Molybdenum 361—Unalloyed powder metallurgy molybdenum.  
1.1.3 Molybdenum Alloy 363—Vacuum arc-cast molybdenum-0.5 % titanium-0.1 % zirconium (TZM) alloy.  
1.1.4 Molybdenum Alloy 364—Powder metallurgy molybdenum-0.5 % titanium-0.1 % zirconium (TZM) alloy.  
1.1.5 Molybdenum 365—Unalloyed vacuum arc-cast molybdenum, low carbon.  
1.1.6 Molybdenum Alloy 366—Vacuum arc-cast molybdenum-30 % tungsten alloy.  
1.1.7 Drawing Grade—A drawing grade is defined, which may be specified as a separate requirement by the purchaser.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.2.1 The ball punch deformation test called for in 8.4 is a test that is specified in the inch-pound system, and original test results used to produce Fig. 2 were all obtained using inch-pound measurements. For this reason, the graph of minimum required cup height as a function of sheet thickness has been retained in its original inch-pound system. The graphical data has been scanned and a straight line fitted to the scan data. The equation of this line is included in both inch-pound and SI units.  
1.3 The following precautionary caveat pertains only to the test method portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the standard requirements for tantalum and tantalum alloy plate, sheet, and strip in the following grades: R05200, R05400, R05255, R05252, and R05240. The various tantalum mill products covered by this specification shall be formed with the conventional extrusion, forging, and rolling equipment normally available in metal working plants. Materials shall be made from vacuum-arc or electron-beam melted ingots or powder metallurgy consolidated unalloyed tantalum and shall be supplied in the annealed condition. Chemical analysis shall be conducted to determine the chemical composition of the materials which shall conform to the requirements for carbon, oxygen, nitrogen, hydrogen, iron, molybdenum, niobium, nickel, silicon, titanium, tungsten, and tantalum. The mechanical properties of the materials shall also meet the specified tensile strength, yield strength, and elongation limits as shall be determined by a longitudinal or transverse tension test method.
SCOPE
1.1 This specification covers unalloyed and alloyed tantalum plate, sheet, and strip as follows.  
1.1.1 R05200, unalloyed tantalum, electron-beam furnace or vacuum-arc melt, or both,  
1.1.2 R05400, unalloyed tantalum, powder-metallurgy consolidation,  
1.1.3 R05255, tantalum alloy, 90 % tantalum, 10 % tungsten, electron-beam furnace of vacuum-arc melt, or both,  
1.1.4 R05252, tantalum alloy, 97.5 % tantalum, 2.5 % tungsten, electron-beam furnace or vacuum-arc melt, or both, and  
1.1.5 R05240, tantalum alloy, 60 % tantalum, 40 % niobium, electron-beam furnace or vacuum-arc melt.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety and/or health problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers unalloyed and alloyed tantalum rod and wire. The materials covered are: R05200, R05400, R05255, R05252, and R05240. These materials shall be made from vacuum-arc melted or electron-beam melted ingots or powder-metallurgy consolidated unalloyed tantalum. The chemical composition shall conform to the required contents of carbon, oxygen, nitrogen, hydrogen, niobium, iron, titanium, tungsten, molybdenum, silicon, nickel, and tantalum. Chemical analysis shall be made. Mechanical properties shall conform to the required tensile strength, yield strength, and elongation.
SIGNIFICANCE AND USE
12.1 For the purpose of determining compliance with the specified limits for requirements on the properties listed in this specification, observed and calculated values shall be rounded as indicated by the rounding method of Practice E29.
SCOPE
1.1 This specification covers unalloyed and alloyed tantalum rod and wire.  
1.2 The materials covered by this specification are:  
1.2.1 R05200, unalloyed tantalum, electron-beam furnace or vacuum-arc melt, or both,  
1.2.2 R05400, unalloyed tantalum, powder-metallurgy consolidation,  
1.2.3 R05255, tantalum alloy, 90 % tantalum, 10 % tungsten, electron-beam furnace or vacuum-arc melt, or both,  
1.2.4 R05252, tantalum alloy, 97.5 % tantalum, 2.5 % tungsten, electron-beam furnace or vacuum-arc melt, or both, and  
1.2.5 R05240 tantalum alloy, 60 % tantalum, 40 % niobium, electron-beam furnace or vacuum-arc melt, or both.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following precautionary caveat pertains only to the test methods portion, Section 13, of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers three grades of zirconium and zirconium alloy forgings. The forgings shall be formed with conventional forging equipment normally found in primary ferrous and nonferrous metal plants. The forgings are furnished in three grades as Grade R60702, Grade R60702, and Grade R60705. Forgings shall be furnished in the annealed conditions. The material shall conform to the requirements as to chemical composition and tensile properties prescribed. Two tension tests shall be made from each lot. Two chemistry tests for hydrogen and nitrogen content shall be made from each lot of finished product. If the results of any tests of any lot do not conform to the requirements specified, retests shall be made on additional forgings of double the original number of the same lot, each of which shall conform to the requirements specified.
SCOPE
1.1 This specification covers niobium-titanium alloy billets, bars, and rods, at 46 to 48 % titanium. This material is used in the manufacture of wire for superconducting applications.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the test methods portion, Section 14, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers seamless and welded titanium and titanium alloy tubing on which the external or internal surface, or both, has been modified by a cold forming process to produce an integral enhanced surface for improved heat transfer. The tubes are used in surface condensers, evaporators, heat exchangers and similar heat transfer apparatus in unfinned end diameters of a specific size. Tubes shall be furnished with unenhanced ends in the annealed condition and shall be suitable for rolling-in operations. Each tube shall be subject to a nondestructive eddy current test, and either a pneumatic or hydrostatic test.
SCOPE
1.1 This specification covers seamless and welded titanium and titanium alloy tubing on which at least part of the external or internal surface has been enhanced by cold forming for improved heat transfer. The tubes are used in surface condensers, evaporators, heat exchangers, coils, and similar heat transfer apparatus in diameters up to and including 1 in. [25.4 mm]. The base tube wall thickness is typically at least 0.049 in. [1.245 mm] average, but lighter gauge may be negotiated with the manufacturer.  
1.2 Tubing purchased to this specification will typically be inserted through close-fitting holes in tubesheets, baffles, or support plates spaced along the tube length such as defined in the Tubular Exchanger Manufacturer’s Association (TEMA) Standard.2 The tube ends will also be expanded, and may then be welded. Tube may also be bent to form U-tubes or be coiled or otherwise formed, although tight radii may require unenhanced length for the bends.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the order. Combining values from the two systems may result in non-conformance. Within the text, the SI units are shown in brackets. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.  
1.4 The following precautionary statement pertains to the test method portion only: Section 8, 9, 10 and S1 of this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers three grades of zirconium and zirconium alloy forgings. The forgings shall be formed with conventional forging equipment normally found in primary ferrous and nonferrous metal plants. The forgings are furnished in three grades as Grade R60702, Grade R60702, and Grade R60705. Forgings shall be furnished in the annealed conditions. The material shall conform to the requirements as to chemical composition and tensile properties prescribed. Two tension tests shall be made from each lot. Two chemistry tests for hydrogen and nitrogen content shall be made from each lot of finished product. If the results of any tests of any lot do not conform to the requirements specified, retests shall be made on additional forgings of double the original number of the same lot, each of which shall conform to the requirements specified.
SCOPE
1.1 This specification2 covers three grades of zirconium and zirconium alloy forgings (see 4.1).  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 The following safety hazards caveat pertains only to the test method portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This test method is primarily used as an acceptance test for products of zirconium, hafnium, and their alloys. This standard has been widely used in the development of new alloys, heat treating practices, and for evaluation of welding techniques.  
5.2 Specimens are normally tested after careful etching and rinsing. Specimens with as-manufactured surfaces may also be tested without further surface removal.  
5.3 When tubing with a second material clad on the inner surface is to be tested, the inner cladding shall be removed prior to the test.
SCOPE
1.1 This test method covers (1) the determination of mass gain, and (2) the surface inspection of products of zirconium, hafnium, and their alloys when corrosion tested in water at 680°F [360°C] or in steam at 750°F [400°C].  
1.2 This test method is to be utilized in its entirety to the extent specified herein as a product acceptance test.  
1.3 This test method may be used on wrought products, castings, powder metallurgy products, and weld metals.  
1.4 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 9.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers hafnium alloyed niobium bar, rod, and wire. The material covered by this specification is R04295, a niobium-base alloy containing hafnium and titanium. The alloy shall conform to the required chemical composition for carbon, oxygen, nitrogen, hydrogen, hafnium, titanium, zirconium, tungsten, tantalum, and niobium. Materials in the annealed condition supplied under this specification shall conform to the required mechanical properties such as tensile strength, yield strength, and elongation. The alloy shall undergo the following test methods: room temperature tension test; elevated temperature tension test; and chemical test.
SIGNIFICANCE AND USE
12.1 The following applies to all specified limits in this standard for purposes of determining conformance with this specification. The observed value or a calculated value shall be rounded off to the nearest unit in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.
SCOPE
1.1 This specification covers hafnium alloyed niobium bar and wire.  
1.2 The material covered by this specification is R04295, niobium-base alloy containing approximately 10 % hafnium and 1 % titanium.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 14, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers foils, sheets, strips, and plates made from UNS R04295 hafnium alloyed niobium ingots and billets. The materials should be in the annealed condition unless otherwise specified. The materials may also be in a forged, rolled, extruded, swaged, or drawn finish in a cleaned, machined, or ground condition. All the products should be formed with conventional extrusion, forging, and rolling equipment normally used in metal working plants.
SCOPE
1.1 This specification covers hafnium alloyed niobium foil, sheet, strip, and plate.  
1.2 The material covered by this specification is R04295, niobium-base alloy containing approximately 10 % hafnium and 1 % titanium.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 14, of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers virgin titanium metal melting stock. This virgin metal is commonly designated as sponge titanium because it is most commonly porous and spongelike in texture, although metal produced electrolytically is granular and is essentially nonporous. Sponge titanium is usually prepared by reduction of titanium tetrachloride and gets its spongelike character from the processes involved in production. This spongy characteristic, however, is not considered essential and may be expected to vary greatly with manufacturing methods. For example, virgin titanium produced electrolytically is crystalline or granular in character and is essentially nonporous. The metal is usually supplied in lump or granular form. The virgin titanium shall be free of scrap, intentionally added contaminants and shall be in uniform, well-mixed blends. The titanium metal shall conform to the chemical composition and Brinell hardness requirements prescribed.
SCOPE
1.1 This specification covers the purchase of virgin titanium sponge metal. This virgin metal is commonly designated as titanium sponge because it is most commonly porous and sponge-like in texture, although metal produced electrolytically is granular and is essentially nonporous.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers hafnium alloyed niobium ingots prepared by vacuum- or plasma- arc melting or electron-beam furnace melting, or a combination of these methods, to produce consolidated metal for processing to various mill shapes. The material shall conform to the required chemical composition prescribed. Each ingot should be tested for soundness by non-destructive test methods, such as dye penetrant and ultrasonic testing. Each ingot shall be tested for chemical composition in at least three positions along the length of the ingot.
SIGNIFICANCE AND USE
10.1 The following applies to all specified limits in this standard for purposes of determining conformance with this specification: The observed value or a calculated value shall be rounded off to the nearest unit in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.
SCOPE
1.1 This specification covers hafnium alloyed niobium ingots prepared by vacuum- or plasma- arc melting or electron-beam furnace melting, or a combination of these methods, to produce consolidated metal for processing to various mill shapes.  
1.2 The material covered by this specification is Grade R04295, niobium-base alloy containing approximately 10 % hafnium and 1 % titanium.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers wrought niobium and niobium alloy seamless and welded tubes. Material covered by this specification shall be made from ingots that are produced by vacuum or plasma arc melting, vacuum electron-beam melting, or a combination of these three methods. Seamless tubes may be made by any seamless method that will yield a product meeting the requirements of this specification. Welded tubing shall be made from flat-rolled products by an automatic or semiautomatic welding process with no addition of filler metal in the welding operation. The niobium and niobium alloy ingots and billets for conversion to finished products covered by this specification shall conform to the requirements for chemical composition of the following elements: carbon, nitrogen, oxygen, hydrogen, zirconium, tantalum, iron, silicon, tungsten, nickel, molybdenum, hafnium, titanium. When specified, the following elements shall be included in the chemical composition of the specimen: boron, aluminum, beryllium, chromium, and cobalt. The materials supplied under these specifications shall be in the fully annealed condition. Finished niobium and niobium alloy tubes shall be free of injurious internal and external imperfections of a nature that will interfere with the purpose for which it was intended. Hydrostatic and pneumatic tests are optional when the purchaser requires. A hydrostatic test shall be performed on each tube and shall withstand without showing bulges, leaks, or other defects.
SIGNIFICANCE AND USE
13.1 For the purposes of determining compliance with the specified limits for requirements of the properties listed in this specification, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.
SCOPE
1.1 This specification covers wrought niobium and niobium alloy seamless and welded tubes as follows:  
1.1.1 R04200-Type 1—Reactor grade unalloyed niobium,  
1.1.2 R04210-Type 2—Commercial grade unalloyed niobium,  
1.1.3 R04251-Type 3—Reactor grade niobium alloy containing 1 % zirconium, and  
1.1.4 R04261-Type 4—Commercial grade niobium alloy containing 1 % zirconium.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the test methods portion of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers unalloyed and alloyed tantalum ingots prepared by vacuum-arc melting, electron-beam melting, or powder-metallurgy consolidation to produce consolidated metal for processing to various mill shapes. The materials covered by this specification are classified according to types: R05200; R05400; R05255; R05252; and R05240. The ingot metal for types R05200, R05255, R05252, and R05240 may be prepared by vacuum-arc melting, electron beam furnace melting, or a combination of these two methods. The metal for type R05400 is defined as powder-metallurgy consolidation unalloyed tantalum. The material shall conform to the chemical composition requirements for carbon, oxygen, nitrogen, hydrogen, niobium, iron, titanium, tungsten, molybdenum, silicon, nickel, and tantalum.
SIGNIFICANCE AND USE
8.1 For the purpose of determining compliance with the specified limit for requirements of the properties listed in the tables, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.
SCOPE
1.1 This specification covers unalloyed and alloyed tantalum ingots prepared by vacuum-arc melting, electron-beam melting, or powder-metallurgy consolidation to produce consolidated metal for processing to various mill shapes.  
1.2 The materials covered by this specification are:  
1.2.1 R05200, unalloyed tantalum, electron-beam furnace or vacuum-arc melt, or both,  
1.2.2 R05400, unalloyed tantalum, powder-metallurgy consolidation,  
1.2.3 R05255, tantalum alloy, 90 % tantalum 10 % tungsten, electron-beam furnace or vacuum-arc melt, or both,  
1.2.4 R05252, tantalum alloy, 97.5 % tantalum 2.5 % tungsten, electron-beam furnace or vacuum-arc melt, or both, and,  
1.2.5 R05240 tantalum alloy, 60 % tantalum 40 % columbium, electron-beam furnace or vacuum-arc melt, or both.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers four grades of wrought niobium and niobium alloy bar, rod, and wire as R04200-Type 1, reactor grade unalloyed niobium; R04210-Type 2, commercial grade unalloyed niobium; R04251-Type 3, reactor grade niobium alloy containing 1 % zirconium; and R04261-Type 4, commercial grade niobium alloy containing 1 % zirconium. The chemical; and mechanical properties requirements, such as Brinell hardness, tensile strength, yield strength, and elongations; as well as the temper designations are detailed.
SIGNIFICANCE AND USE
13.1 For the purposes of determining compliance with the specified limits for requirements of the properties listed in this specification, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.
SCOPE
1.1 This specification covers four grades of wrought niobium and niobium alloy bar, rod, and wire as follows:  
1.1.1 R04200-Type 1—Reactor grade unalloyed niobium,  
1.1.2 R04210-Type 2—Commercial grade unalloyed niobium,  
1.1.3 R04251-Type 3—Reactor grade niobium alloy containing 1 % zirconium, and  
1.1.4 R04261-Type 4—Commercial grade niobium alloy containing 1 % zirconium.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers five grades of wrought niobium and niobium alloy strip, sheet, and plate. These are reactor grade unalloyed niobium (R04200-Type 1), commercial grade unalloyed niobium (R04210-Type 2), reactor grade niobium alloy containing 1% zirconium (R04251-Type 3), commercial grade niobium alloy containing 1% zirconium (R04261-Type 4), and RRR grade pure niobium (R0xxxx-Type 5). The RRR grade pure niobium is used in superconducting applications that require ultra high purity, making it conducive to very large grains that can adversely affect formability. It is therefore not recommended for other applications. The materials shall be made from ingots produced by vacuum or plasma arc welding, vacuum electron-beam melting, or a combination of these three methods. The various niobium mill products covered by this specification are formed with the conventional extrusion, forging, swaging, rolling, and drawing equipment normally available in metal working plants. Samples for chemical and tension testing shall be taken from the finished material after the metallurgical processing to determine conformity to this specification. The samples may be taken prior to final inspection and minor surface conditioning by abrasion and pickling shall be representative of the finished product.
SIGNIFICANCE AND USE
13.1 For the purposes of determining compliance with the specified limits for requirements of the properties listed in this specification, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.
SCOPE
1.1 This specification covers five grades of wrought niobium and niobium alloy strip, sheet, and plate as follows:  
1.1.1 R04200-Type 1—Reactor grade unalloyed niobium,  
1.1.2 R04210-Type 2—Commercial grade unalloyed niobium,  
1.1.3 R04251-Type 3—Reactor grade niobium alloy containing 1 % zirconium,  
1.1.4 R04261-Type 4—Commercial grade niobium alloy containing 1 % zirconium, and.  
1.1.5 R04220-Type 5—RRR grade pure niobium.
Note 1: This grade of niobium is used in superconducting applications that require the ultra high purity. Because of the high purity the product is conducive to very large grains that can adversely affect formability. It is not recommended for other applications.  
1.2 Except for dimensional tolerances in Table 1, the values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. (A) Tolerance on thickness of sheet over 24 in. (610 mm) wide shall be ±10 % of the thickness.(B) Tolerance on width of sheared sheet shall be ±1/16 in. (±1.6 mm) and on sheared plate shall be ±1/8 in. (±3.2 mm) up to material thickness of 0.375 in. (9.5 mm).  
1.3 The following precautionary caveat pertains only to the test methods portion of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.