iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D329-07

(Specification)

Standard Specification for Acetone

Standard Specification for Acetone

SCOPE
1.1 This specification covers acetone (99.5 % grade).
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in 1.5 and 4.1.
1.4 This specification specifies the use of a U.S. Occupational Safety and Health Administration (OSHA)-designated hazardous chemical, acetone. For hazard information and guidance see the supplier's Material Safety Data Sheet.

General Information

Status
Historical
Publication Date
31-May-2007
ICS
71.080.80 - Aldehydes and ketones
Technical Committee
D01 - Paint and Related Coatings, Materials, and Applications
Drafting Committee
D01.35 - Solvents, Plasticizers, and Chemical Intermediates
Current Stage
Ref Project

Relations

Replaces
ASTM D329-02 - Standard Specification for Acetone
Effective Date
01-Jun-2007
Replaced By
ASTM D329-07e1 - Standard Specification for Acetone <a href="#fn00002"></a>
Effective Date
01-Jun-2007
Referred By
ASTM D1726-11(2019) - Standard Test Methods for Hydrolyzable Chloride Content of Liquid Epoxy Resins
Effective Date
01-Jun-2007
Referred By
ASTM D7280-20 - Standard Test Method for Quinoline-Insoluble (QI) Content of Tar and Pitch by Stainless Steel Crucible Filtration
Effective Date
01-Jun-2007
Referred By
ASTM D4312-20 - Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch (Short Method)
Effective Date
01-Jun-2007
Referred By
ASTM E165/E165M-23 - Standard Practice for Liquid Penetrant Testing for General Industry
Effective Date
01-Jun-2007
Referred By
ASTM D2384-23 - Standard Test Methods for Traces of Volatile Chlorides in Butane-Butene Mixtures
Effective Date
01-Jun-2007
Referred By
ASTM F3440-21 - Standard Test Method for Corrosion of Low-Embrittling Zinc-Nickel Plate by Aircraft Maintenance Chemicals
Effective Date
01-Jun-2007
Referred By
ASTM D2764-20 - Standard Test Method for Dimethylformamide-Insoluble (DMF-I) Content of Tar and Pitch
Effective Date
01-Jun-2007
Referred By
ASTM D2318-20 - Standard Test Method for Quinoline-Insoluble (QI) Content of Tar and Pitch
Effective Date
01-Jun-2007
Referred By
ASTM F482-09(2020) - Standard Practice for Corrosion of Aircraft Metals by Total Immersion in Maintenance Chemicals
Effective Date
01-Jun-2007
Referred By
ASTM F502-08(2019) - Standard Test Method for Effects of Cleaning and Chemical Maintenance Materials on Painted Aircraft Surfaces
Effective Date
01-Jun-2007
Referred By
ASTM D1363-06(2019) - Standard Test Method for Permanganate Time of Acetone and Methanol
Effective Date
01-Jun-2007
Referred By
ASTM D268-22 - Standard Guide for Sampling and Testing Volatile Solvents and Chemical Intermediates for Use in Paint and Related Coatings and Material
Effective Date
01-Jun-2007
Referred By
ASTM F483-09(2020) - Standard Practice for Total Immersion Corrosion Test for Aircraft Maintenance Chemicals
Effective Date
01-Jun-2007

Buy Standard

ASTM D329-07 - Standard Specification for AcetoneASTM D329-07 - Standard Specification for Acetone
PreviousNext
Technical specification
ASTM D329-07 - Standard Specification for Acetone
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D 329 – 07
Standard Specification for
,
1 2
Acetone
This standard is issued under the fixed designation D 329; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* D 1353 Test Method for Nonvolatile Matter in Volatile
Solvents for Use in Paint, Varnish, Lacquer, and Related
1.1 This specification covers acetone (99.5 % grade).
Products
1.2 The following applies to all specified limits in this
D 1363 Test Method for Permanganate Time of Acetone
standard; for purposes of determining conformance with this
and Methanol
standard, an observed value or a calculated value shall be
D 1364 Test Method for Water in Volatile Solvents (Karl
rounded off “to the nearest unit” in the last right-hand digit
Fischer Reagent Titration Method)
used in expressing the specification limit, in accordance with
D 1476 Test Method for Heptane Miscibility of Lacquer
the rounding-off method of PracticeE29.
Solvents
1.3 The values stated in SI units are to be regarded as
D 1613 Test Method for Acidity in Volatile Solvents and
standard. No other units of measurement are included in this
Chemical Intermediates Used in Paint, Varnish, Lacquer,
standard.
and Related Products
1.4 This standard does not purport to address all of the
D 1614 Test Method for Alkalinity in Acetone
safety concerns, if any, associated with its use. It is the
D 1722 Test Method forWater Miscibility ofWater-Soluble
responsibility of the user of this standard to establish appro-
Solvents
priate safety and health practices and determine the applica-
D 4052 Test Method for Density and Relative Density of
bility of regulatory limitations prior to use. Specific hazard
Liquids by Digital Density Meter
statements are given in 1.5 and 4.1.
D 5386 Test Method for Color of Liquids UsingTristimulus
1.5 This specification specifies the use of a U.S. Occupa-
Colorimetry
tional Safety and Health Administration (OSHA)-designated
E29 Practice for Using Significant Digits in Test Data to
hazardous chemical, acetone. For hazard information and
Determine Conformance with Specifications
guidance see the supplier’s Material Safety Data Sheet.
E 300 Practice for Sampling Industrial Chemicals
2. Referenced Documents 2.2 U.S. Federal Specification:
3
PPP-C-2020 Chemicals, Liquid, Dry, and Paste: Packaging
2.1 ASTM Standards:
4
of
D 268 Guide for Sampling and Testing Volatile Solvents
and Chemical Intermediates for Use in Paint and Related
3. Properties
Coatings and Material
3.1 Acetone (99.5 % grade) shall conform to the following
D 1078 Test Method for Distillation Range of Volatile
requirements:
Organic Liquids
Acidity (free acid as acetic) 0.002 (equivalent to 0.019 mg of KOH/g of
D 1209 Test Method for Color of Clear Liquids (Platinum-
wt %, max sample)
Cobalt Scale)
Aldehydes passes test
D 1296 Test Method for Odor of Volatile Solvents and
Alkalinity (as ammonia) 0.001
wt %, max
Diluents
Apparent specific gravity:
20/20°C 0.7910 to 0.7930 or
25/25°C 0.7865 to 0.7885
1
This specification is under the jurisdiction of ASTM Committee D01 on Paint
Assay wt %, min 99.5
and Related Coatings, Materials, andApplications and is the direct responsibility of
Color Pt-Co, max (Note 1)5
Subcommittee D01.35 on Solvents, Plasticizers, and Chemical Intermediates.
Distillation range 760 shall distill entirely within a 1.0°C range which
CurrenteditionapprovedJune1,2007.PublishedJuly2007.Originallyapproved
mmHg (Note 3) shall include 56.1°C
in 1931. Last previous edition approved in 2002 as D 329 – 02.
2
The compound is also known under the names dimethyl ketone and
2-propanone.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
4
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
Standards volume information, refer to the standard’s Document Summary page on Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
the ASTM website. www.dodssp.daps.mil.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D329–07
quickly in an ice bath with vigorous stirring. Any turbidity
Nonvolatile matter 5
mg/100 mL, max
produced in the specimen solution shall be no greater than that
Odor (Note 3) nonresidual
produced in the control.
Permanganate time color of added KMnO must be retained for at
4
least 30 minutes a
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D3893-03(2023)(Test Method)
Standard Test Method for Purity of Methyl Amyl Ketone and Methyl Isoamyl Ketone by Gas Chromatography

SIGNIFICANCE AND USE
4.1 This procedure is designed to determine the purity of the two ketones, methyl isoamyl ketone and methyl amyl ketone, and to obtain the concentration of their various impurities, several of which are critical in the application of these solvents.
SCOPE
1.1 This test method covers the determination of the purity of methyl amyl ketone and methyl isoamyl ketone. In addition, the method determines total ketones and various impurities which may include acetone, isopropyl alcohol, methyl propyl ketone, methyl isobutyl ketone, methyl butyl ketone, methyl isobutyl carbinol, mesityl oxide, methyl isoamyl ketone, methyl butyl carbinol, methyl amyl ketone, and diisobutyl ketone.  
1.2 Water and acid cannot be determined by this test method. They must be determined by other appropriate ASTM procedures, and the results used to normalize the chromatographic data.  
1.3 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded “off to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 For hazard information and guidance, see the supplier’s Safety Data Sheet.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D1614-09(2023)(Test Method)
Standard Test Method for Alkalinity in Acetone

SIGNIFICANCE AND USE
4.1 This test method provides a measurement of alkalinity in acetone. The results of this measurement can be used for specification acceptance.
SCOPE
1.1 This test method covers the determination in acetone of alkalinity calculated as ammonia (NH3).  
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For specific hazard information and guidance, consult the supplier’s Safety Data Sheet.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2916-09(2023)(Specification)
Standard Specification for Isophorone

ABSTRACT
This specification covers isophorone volatile solvents used in paints, varnishes, lacquers, and related products. Isoprophone should conform to the specified requirements on apparent specific gravity, color, distillation, purity, acidity as acetic acid, and water content.
SCOPE
1.1 This specification covers isophorone2 (98 % grade) for use in paint, varnish, lacquer, and related products.  
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For specific hazard information and guidance, see the supplier’s Safety Data Sheet for materials listed in this specification.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D3329-03(2023)(Test Method)
Standard Test Method for Purity of Methyl Isobutyl Ketone by Gas Chromatography

SIGNIFICANCE AND USE
4.1 This test method provides a measurement of commonly found impurities in commercially available methyl isobutyl ketone. The measurement of these impurities and the results thereof can individually or when totaled and subtracted from 100 (assay) be used for specification acceptance.
SCOPE
1.1 This test method covers the determination of the purity of methyl isobutyl ketone (MIBK) by gas chromatography and in addition provides a means for measuring certain impurities such as methyl isobutyl carbinol which are of interest. Impurities such as water and acidity are measured by other appropriate ASTM procedures and the results are used to normalize the chromatographic value.  
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the round-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 For specific hazard information and guidance, see the supplier’s Safety Data Sheet for the materials listed in this test method.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D2379-09(2023)(Test Method)
Standard Test Method for Acidity of Formaldehyde Solutions

SIGNIFICANCE AND USE
4.1 This test method provides a measurement of acidity (as formic acid) in formaldehyde solutions. The results of these measurements can be used for specification acceptance.
SCOPE
1.1 This test method covers the determination of the acidity of commercially available formaldehyde solutions.  
1.2 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For hazard information and guidance, see the supplier’s Safety Data Sheet.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2378-22(Specification)
Standard Specification for Formaldehyde 50 % Grade Uninhibited and 37 % Grade Inhibited and Uninhibited

ABSTRACT
This specification covers the properties and requirements for 50 % uninhibited formaldehyde and 37 % uninhibited and inhibited formaldehyde. Specimens shall be suitably sampled and tested, and shall meet the specified values of the following properties: apparent specific gravity; formaldehyde content; acidity; color (Pt-Co scale); iron content; methanol content; and appearance.
SCOPE
1.1 This specification covers 50 % uninhibited formaldehyde and 37 % uninhibited and inhibited formaldehyde.  
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2194-22(Test Method)
Standard Test Method for Concentration of Formaldehyde Solutions

SIGNIFICANCE AND USE
4.1 This test method provides a measurement of formaldehyde content (assay) of formaldehyde solutions. The results of these measurements can be used for specification acceptance.
SCOPE
1.1 This test method covers the determination of the formaldehyde content of commercially available formaldehyde solutions ranging in concentration from 36 to 55 weight %.  
1.2 For purposes of determining conformance of an observed value or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For hazard information and guidance, see the supplier's Material Safety Data Sheet.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2087-22(Test Method)
Standard Test Method for Iron in Formaldehyde Solutions

SIGNIFICANCE AND USE
4.1 This test method provides a measurement of iron content of formaldehyde solutions. The results of these measurements can be used for specification acceptance.
SCOPE
1.1 This test method covers the determination of the total iron content of formaldehyde solutions.  
1.2 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For hazard information and guidance, see the supplier's Material Safety Data Sheet.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2086-22(Test Method)
Standard Test Method for Acidity in Vinyl Acetate and Acetaldehyde

SIGNIFICANCE AND USE
4.1 This test method provides a measurement of total acidity in vinyl acetate and acetaldehyde. The results of these measurements can be used for specification acceptance.
SCOPE
1.1 This test method covers the determination of total acidity as acetic acid in refined vinyl acetate and acetaldehyde.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 For purposes of determining conformance of an observed value or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.4 For hazard information and guidance, see the supplier's Material Safety Data Sheet.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 8.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2804-22(Test Method)
Standard Test Method for Purity of Methyl Ethyl Ketone By Gas Chromatography

SIGNIFICANCE AND USE
4.1 This test method provides a measurement of commonly found impurities in commercially available methyl ethyl ketone. The measurement of these impurities and the results thereof can individually or when totaled and subtracted from 100 (assay) be used for specification purposes.
SCOPE
1.1 This test method covers the determination of the purity of methyl ethyl ketone by gas chromatography. Impurities including water, acidity, and nonvolatile matter are measured by appropriate ASTM procedures and the results are used to normalize the chromatographic value.  
1.2 For purposes of determining conformance of an observed value or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For hazard information and guidance, see the supplier's Material Safety Data Sheet.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off