ASTM F861-14
(Specification)Standard Specification for Commercial Dishwashing Racks
Standard Specification for Commercial Dishwashing Racks
ABSTRACT
This specification covers racks used in commercial spray type dishwashing machines and for storage of clean tableware. Commercial dishwashing racks shall be classified as follows: Type I (Types IA, IB, IC, ID, IE, and IF); Type II (Type IIA, IIB, IIC, IID, and IIE); Type III; Type IV; Type V; and Type VI. Impact test, bow test, visual examination, and dimensional examination shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification covers racks used in commercial spray type dishwashing machines and for storage of clean tableware.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazard caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F861 −14 AnAmerican National Standard
Standard Specification for
1
Commercial Dishwashing Racks
ThisstandardisissuedunderthefixeddesignationF861;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 3. Classification
1.1 This specification covers racks used in commercial
3.1 Commercial dishwashing racks shall be classified as
spray type dishwashing machines and for storage of clean follows:
tableware.
3.2 Type I—Compartment tray/plate rack with six compart-
1.2 The values stated in inch-pound units are to be regarded
ments.
as standard. The values given in parentheses are mathematical
3.2.1 Type IA—Service tray rack with six compartments.
conversions to SI units that are provided for information only
3.2.2 Type IB—Flatware rack.
and are not considered standard.
3.2.3 Type IC—Plate rack with seven compartments (nomi-
nal 16by16 in. (406 by 406 mm)).
1.3 The following safety hazard caveat pertains only to the
test method portion, Section 8, of this specification:This 3.2.4 Type ID—Flatwarerack(nominal16by16in.(406by
406 mm)).
standard does not purport to address the safety concerns, if
any, associated with its use. It is the responsibility of the user 3.2.5 Type IE—Circular plate rack.
of this standard to establish appropriate safety and health 3.2.6 Type IF—Plate rack.
practices and determine the applicability of regulatory limita-
3.3 Type II—Cup/Bowl rack.
tions prior to use.
3.3.1 Type IIA—Tumbler rack.
3.3.2 Type IIB—Cup rack.
2. Referenced Documents
3.3.3 Type IIC—Compartmented cup rack.
2
2.1 ASTM Standards:
3.3.4 Type IID—Cup/Bowl rack (nominal 16by16 in. (406
A240Specification for Chromium and Chromium-Nickel
by 406 mm)).
Stainless Steel Plate, Sheet, and Strip for PressureVessels
3.3.5 Type IIE—Circular compartmented cup, bowl, and
and for General Applications
flatware rack.
3
2.2 American National Standard
3.4 Type III—Carrier cylinder.
ANSI Z1.4Sampling Procedures and Tables for Inspection
3.4.1 Type IV—Flatware cylinder (plastic).
by Attributes
3.5 Type V—Flatware cylinder (corrosion-resistant steel).
4
2.3 NSF International
NSF/ANSI 3Commercial Warewashing Equipment 3.6 Type VI—Special racks (see 6.7).
NSF/ANSI 51Food Equipment Materials
NSF Food Service Equipment Listing
4. Ordering Information
4.1 Purchasers should select the preferred options permitted
herein and include the following information in the procure-
1
This specification is under the jurisdiction of ASTM Committee F26 on Food
ment document:
Service Equipmentand is the direct responsibility of Subcommittee F26.01 on
4.1.1 Title, designation, and year of issue of this specifica-
Cleaning and Sanitation Equipment.
CurrenteditionapprovedJune1,2014.PublishedJuly2014.Originallyapproved tion.
ε1
in 1984. Last previous edition approved in 2008 as F861–94(2008) . DOI:
4.1.2 Type and style.
10.1520/F0861-14.
4.1.3 Material (See 5.2.1 and 5.2.2).
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
4.2 The overall height and the maximum diameter, exclud-
Standards volume information, refer to the standard’s Document Summary page on
ing the handle of the cup, must be submitted when ordering
the ASTM website.
3
Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St., racks to meet Type IIC (see 6.3).
4th Floor, New York, NY 10036.
4
4.3 When ordering special racks (Type VI), dimensional
Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd.,Ann
Arbor, MI 48113-0140. data of overall height and maximum diameter of ware must be
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F861−14
furnished. For cups, exclude handle from overall diameter to hold no less than eight plates for washing and sanitizing in
measurement (see 6.3). a single tank commercial dishwashing machine of circular
shape.
5. Materials and Manufacture
6.2.6 Type IF (Plate)—Rack shall be suitable for holding
9-in.(229-mm)dinnerplates.Therackshallbedividedtohold
5.1 Materials:
no less than sixteen plates for washing and sanitizing in a
5.1.1 Corrosion-Resistant Steel—Corrosion-resistant steel
commercial dishwashing machine.
shallconformtorequirementsofany300seriesstainlesssteels
specified in Specification A240.
6.3 Type II (Rack, Cup/Bowl)—Rack shall be suitable for
5.1.2 Molded Plastic—Racks shall conform to NSF/ANSI
1 3
holding 10 ⁄2 oz (311 mL
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: F861 − 94 (Reapproved 2008) F861 − 14 An American National Standard
Standard Specification for
1
Commercial Dishwashing Racks
This standard is issued under the fixed designation F861; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1
ε NOTE—Editorially corrected 2.3 in December 2008.
1. Scope
1.1 This specification covers racks used in commercial spray type dishwashing machines and for storage of clean tableware.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazard caveat pertains only to the test method portion, Section 8, of this specification:This standard
does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard
to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
A167A240 Specification for StainlessChromium and Heat-Resisting Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for
Pressure Vessels and for General Applications (Withdrawn 2014)
3
2.2 American National Standard
ANSI Z1.4 Sampling Procedures and Tables for Inspection by Attributes
4
2.3 NSF International
ANSI/NSFNSF/ANSI 3 Commercial Warewashing Equipment
ANSI/NSFNSF/ANSI 51 Food Equipment Materials
NSF Food Service Equipment Listing
3. Classification
3.1 Commercial dishwashing racks shall be classified as follows:
3.2 Type I—Compartment tray/plate rack with six compartments.
3.2.1 Type IA—Service tray rack with six compartments.
3.2.2 Type IB—Flatware rack.
3.2.3 Type IC—Plate rack with seven compartments (nominal 16 × 16 in.).16 by 16 in. (406 by 406 mm)).
3.2.4 Type ID—Flatware rack (nominal 16 × 16 in.).16 by 16 in. (406 by 406 mm)).
3.2.5 Type IE—Circular plate rack.
3.2.6 Type IF—Plate rack.
3.3 Type II—Cup/Bowl rack.
3.3.1 Type IIA—Tumbler rack.
3.3.2 Type IIB—Cup rack.
3.3.3 Type IIC—Compartmented cup rack.
3.3.4 Type IID—Cup/Bowl rack (nominal 16 × 16 in.).16 by 16 in. (406 by 406 mm)).
1
This specification is under the jurisdiction of ASTM Committee F26 on Food Service Equipmentand is the direct responsibility of Subcommittee F26.01 on Cleaning
and Sanitation Equipment.
Current edition approved Oct. 1, 2008June 1, 2014. Published December 2008July 2014. Originally approved in 1984. Last previous edition approved in 20032008 as
ε1
F861 – 94 (2003).(2008) . DOI: 10.1520/F0861-94R08E01.10.1520/F0861-14.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036.
4
Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F861 − 14
3.3.5 Type IIE—Circular compartmented cup, bowl, and flatware rack.
3.4 Type III—Carrier cylinder.
3.4.1 Type IV—Flatware cylinder (plastic).
3.5 Type V—Flatware cylinder (corrosion-resistant steel).
3.6 Type VI—Special racks (see 6.7).
4. Ordering Information
4.1 Purchasers should select the preferred options permitted herein and include the following information in the procurement
document:
4.1.1 Title, designation, and year of issue of this specification.
4.1.2 Type and style.
4.1.3 Material (See 5.2.1 and 5.2.2).
4.2 The overall height and the maximum diameter, excluding the handle of the cup, must be submitted when ordering racks to
meet Type IIC (see 6.3).
4.3 When ordering special racks (Type VI), dimensional data of overall height and maximum diameter of ware must be
furnished. For cups, exclude handle from overall diameter measurement (see 6.3).
5. Materials and Manufacture
5.1 Materials:
5.1.1 Corrosion-Resistant Steel—Corrosion-r
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.