F26.01 - Cleaning and Sanitation Equipment

ABSTRACT
This specification covers multiple tank, automatic rack less conveyor type, commercial dishwashing machines. These machines can be classified into two types: Type 1 machines shall be designed and supplied to accept the feeding of soiled tableware from the right side, when facing the front of the machine while Type II shall be designed and supplied to accept the feeding of soiled tableware from the left side, when facing the front of the machine. The dishwashing machines have three kinds of styles: Style 1 is a steam heated machine, with two classes namely Class A which uses injectors and Class B which uses heat exchange coils. Style 2 is an electrically heated dishwashing machine. Style 3 on the other hand is gas heated with two classes namely Class C which uses natural gas and Class D which uses LP gas. In addition, these dishwashing machines can be classified into three groups according to size and capacity: Group A, Group B, and Group C. Materials used in the manufacture of these machines shall consist of corrosion-resistant steel, corrosion resisting material, nickel-copper alloy and plastics. The dishwashing machine shall be complete so that when connected to the specified source of power, water supply, heating means (steam, electric, or gas), drainage, detergent, and rinse agent feeder as applicable, the unit can be used for its intended function. Dishwashers shall be rigid, quiet in operation, free from objectionable vibration, and so constructed as to prevent objectionable splashing of water to the outside of the machine. Operational test, leakage test, and performance profiles shall be done in order to determine the overall efficiency of the dishwashing machine.
SCOPE
1.1 This specification covers multiple tank, automatic rackless conveyor type, commercial dishwashing machines.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are provided for information only.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers single tank, automatic rack type, hot water sanitizing commercial dishwashing machines. Covered by this specification are dishwashing machines of various types (Types I and II based on feed direction, from right or left, respectively), styles (Styles 1-3 based on method of heating: steam, electric, or gas), classes (Classes A-D based on heat source: injector, heat exchange coil, natural gas, or LP gas), sizes, and capacities. Components comprising the dishwashing machine shall be manufactured from corrosion-resistant steel (tank, scrap trays or strainers, overflow drain, access door/s, and legs), corrosion-resisting materials (conveyor, piping and fittings, valves, and spray assemblies), nickel-copper alloys, and plastics. Pump casings shall be of cast iron or corrosion-resisting material. When specified, the dishwashing machine assembly may include a final rinse booster, detergent feeder, and rinse agent feeder. The dishwashing machine shall be tested for performance standards compliance and noise level as well as for operational, leakage, and performance profile requirements. All tests shall comply with the requirements specified.
SCOPE
1.1 This specification covers single tank, automatic rack conveyor type, commercial dishwashing machines.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification applies to dehydrators intended for removing liquid by evaporation from processed or unprocessed food scraps and limited amounts of cardboard, paper, and biodegradable food service ware. Dehydrators shall be of the following type, size, and options as specified:
SCOPE
1.1 This specification covers dehydrators intended for removing liquid by evaporation from processed or unprocessed food scraps and limited amounts of cardboard, paper, and biodegradable food service ware.  
1.2 The values as stated in inch-pound units are to be regarded as the standard. The values stated in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test method portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification establishes the material, design, and performance requirements pertinent to the construction of commercial pulping and waterpress assemblies that are intended for grinding food scraps, paper, cardboard, and disposable plastic food-service ware. Unless otherwise specified, materials used to fabricate pulpers and waterpresses may include corrosion-resistant steel and other corrosion-resisting materials, abrasion-resistant cast iron, austenitic gray iron, copper tube, brass pipe, alloy steel, black and galvanized pipe, gaskets and seals, perforated metal, stainless steel pipe, plastic piping and fitting, and austenitic gray iron pipe fitting. Assembled pulpers and waterpresses shall meet operational, electrical, lubrication, finish, and performance requirements, and should function satisfactorily as specified.
SCOPE
1.1 This specification covers commercial pulping and waterpress assemblies intended for grinding of food scraps, paper, cardboard, and disposable plastic food-service ware.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test method portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers manually fed, motor-driven rotary conveyor type, automatically controlled, commercial pot, pan, and utensil washing machines. The washer shall be of the following type, and class as specified. Motor-driven continuous rotary conveyor: type I - one door (front loading); type II - one or two door (pass-through corner operation); and type III - one or two door (pass-through straight line operation). Style and class: style 1 - steam heated; style 2 - electric heat; class A - injection; and class B - heat exchange coil. The design, construction, and performance requirements of the washing machine are presented in details. The operational test; leakage test; and energy and productivity test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers manually fed, motor-driven rotary conveyor type, automatically controlled, commercial pot, pan, and utensil washing machines, hereinafter referred to as “the washer.”  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary statement pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the requirements for manually fed, motor-driven vertically oscillating arm type, automatically controlled, commercial pot, pan, and utensil washing machine (also referred to as "the washer"). The washer is of one rack capacity (Type I) and is available in either Style A (one door/front loading) or Style B (three door/pass-through with front load door). Heat shall be provided to the washer through steam (Style 1) by injection (Class A) or heat exchange coil (Class B) or through electric means (Style 2). The washer and its components shall be manufactured free of defects. Piping and fittings shall be manufactured from corrosion-resisting material or heat-resisting plastic material. Valves, spray assemblies, and overflow drain shall be manufactured from corrosion-resisting materials. Tank and housing shall be constructed of corrosion-resistant steel. Scrap trays (strainers), access door/s, and legs shall be constructed of corrosion-resistant steel or other corrosion-resisting material. The pump motor shall be mounted on the tank or rigid steel base, with the pump casing being of cast iron or corrosion-resisting material. When specified, a final rinse booster heater and/or detergent feeder may be provided. The washer shall be operated at ambient room temperature. Tests for performance standards and operational compliance as well as for noise level, leakage, energy, and productivity requirements shall be performed and shall conform to the requirements specified.
SCOPE
1.1 This specification covers manually fed, motor-driven vertically oscillating arm type, automatically controlled, commercial pot, pan, and utensil washing machines, hereinafter referred to as “the washer.”  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary statement pertains only to the test methods portion, Section 9 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the material, design, and performance requirements pertinent to the construction of water-driven rotary spray type, stationary rack commercial pot, pan, and utensil washing machines that are manually fed yet automatically controlled to uniformly wash, rinse, and heat-sanitize food preparation utensils. Representative production models of the washers shall pass performance, operation, leakage, and energy and productivity tests, and should function satisfactorily as specified. Certification, product marking, and packaging are also considered.
SCOPE
1.1 This specification covers manually fed, spray-type stationary rack, automatically controlled, water-driven rotary spray commercial pot, pan, and utensil washing machines, herein referred to as “the washer.”  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers multiple tank automatic rack-type commercial dishwashing machines. Dishwashing machines shall be of the following types, styles, and classes, as specified: Type I-this machine shall be designed and supplied to accept the feeding of soiled tableware from the right side, when facing the front of the machine; and Type II-this machine shall be designed and supplied to accept the feeding of soiled tableware from the left side, when facing the front of the machine. Style 1 - steam heated; Style 2 - electrically heated; Style 3 - gas-heated; and Style 4 - pre-wash unit. Class A - injectors; Class B - heat exchange coils; Class C - natural gas; and Class D - LP gas. The construction requirements; electrical, steam and gas equipment requirements; lubrication requirements; treatment and painting requirements; and performance requirements are presented in details.
SCOPE
1.1 This specification covers multiple tank automatic rack-type commercial dishwashing machines, including continuous type, oval shaped, with horizontal table conveyor systems.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers commercial powered pot, pan, and utensil washing sinks of the following types, styles, and classes: Type I, Type II, Style 1 (Class A and Class B), and Style 2, having the specified sizes for (1) drainboards, soiled and clean ends, (2) scrapper section, (3) wash sink, (4) rinse sink, and (5) sanitizer sink. The materials shall conform to the specified requirements and include: corrosion-resistant steel, corrosion-resisting material, nickel-copper alloy, and plastics. Construction requirements for the following are detailed: (1) piping, tubing, fittings, and valves, (2) spray assemblies, (3) tank, (4) overflow, (5) frame, (6) legs (feet), (7) pump and motor assemblies, and (8) heating. The electrical equipment requirements for the motors, controls, and wiring and circuit devices; lubrication requirements; and requirements for treatment and painting, are specified. Powered pot, pan, and utensil washing sinks shall conform to the specified performance requirements including noise level. Operational, leakage, and performance tests shall be performed.
SCOPE
1.1 This specification covers commercial powered pot, pan and utensil washing sinks.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers manually fed, spray-type, stationary rack, automatically controlled, dump type, chemical sanitizing commercial dishwashing machines. Dishwashing machines shall be of the following types, styles, classes: type I - Straight-through model, 34 in. nominal table height. This machine is used in line with table on each side, type II - Corner model, 34 in. nominal table height. This machine is used in corner placement forming a 90° table on each side, and type III - Under counter, front load. This machine may be installed under counters; style A - single rack, and style B - double rack. No leakage shall occur when tested at pressures up to 125 % of the manufacturer's recommended supply line pressure. The dishwasher materials, construction, operation cycle, electrical equipment, lubrication, and coating shall meet the requirements prescribed.
SCOPE
1.1 This specification covers manually fed, spray-type, stationary rack, automatically controlled, dump type, chemical sanitizing commercial dishwashing machines.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers commercial food waste disposers intended for the grinding of food waste. Commercial disposers shall be of two types, namely: Type and Type II. The materials shall conform to the specified requirements and include the following: corrosion resistant steel, aluminum alloy, abrasion-resistant cast iron, austenitic gray iron, copper tube, brass pipe, alloy steel, black and galvanized pipe, and gaskets and seals. The disposer construction requirements including requirements for the following are detailed: (1) valves and fittings, (2) hopper (upper housing), (3) grind chamber (lower housing), (4) shredded ring, (5) flywheel, (6) cutting teeth, (7) water seal, (8) bearings, (9) motor, (10) wiring and circuit protective devices, (11) support leg(s), and (12) plating, coating, and painting. Leakage and operations test shall be performed.
SCOPE
1.1 This specification covers commercial food waste disposers intended for the grinding of food waste.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers pulper assemblies intended for grinding of food scraps and limited amounts of cardboard, paper, and disposable plastic food service wear. Pulper assemblies shall be of the following types: Type A and Type B. Lubricating points shall be readily accessible, and the pulper shall be lubricated with the proper amount of lubricant prior to delivery. All surfaces of the machine, other than corrosion-resistant materials, shall be protected against corrosion in the use environment and shall present a neat appearance. Test method shall be performed to demonstrate the ability of the unit to meet the capacity requirements and to insure that there is no leakage during operation.
SCOPE
1.1 This specification covers pulper assemblies intended for grinding of food scraps and limited amounts of cardboard, paper, and disposable plastic food service ware.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test method portion, Section 13, of this specification:  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers racks used in commercial spray type dishwashing machines and for storage of clean tableware. Commercial dishwashing racks shall be classified as follows: Type I (Types IA, IB, IC, ID, IE, and IF); Type II (Type IIA, IIB, IIC, IID, and IIE); Type III; Type IV; Type V; and Type VI. Impact test, bow test, visual examination, and dimensional examination shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification covers racks used in commercial spray type dishwashing machines and for storage of clean tableware.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazard caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers detergent feeders, rinse additive feeders, and sanitizing agent feeders intended to automatically maintain the concentration of additives in the wash, recirculated rinse, or non-recirculated rinse water of commercial spray- type dish-washing and glass-washing machines. Detergent, rinse additive, and sanitizing agent feeders shall be of the following types and styles: Types I, II, III, IV, V, and VI; and Style I; II; III; IV; V; and VI. Materials used shall be free from defects that would adversely affect the performance or maintainability of individual components or of the overall assembly. The feeder shall be complete so that when connected to the specified source of power (electrical or water, or both), the unit can be used for its intended function. Feeders shall be tested in accordance with specified requirements.
SCOPE
1.1 This specification covers detergent feeders, rinse additive feeders, and sanitizing agent feeders intended to automatically maintain the concentration of additives in the wash, recirculated rinse, or non-recirculated rinse water of commercial spray-type dishwashing and glasswashing machines.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the material, design, and performance requirements pertinent to the construction of spray-type, stationary rack commercial dishwashing machines that are manually fed yet automatically controlled to uniformly wash, rinse, and sanitize eating and drinking utensils. Representative production models of the washers shall pass performance, operation, leakage, and energy and productivity tests, and should function satisfactorily as specified. Certification, product marking, and packaging are also considered.
SCOPE
1.1 This specification covers manually fed, spray-type, stationary rack, automatically controlled, hot water and chemical sanitizing commercial dishwashing machines.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the test methods portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers multiple tank, automatic rack less conveyor type, commercial dishwashing machines. These machines can be classified into two types: Type 1 machines shall be designed and supplied to accept the feeding of soiled tableware from the right side, when facing the front of the machine while Type II shall be designed and supplied to accept the feeding of soiled tableware from the left side, when facing the front of the machine. The dishwashing machines have three kinds of styles: Style 1 is a steam heated machine, with two classes namely Class A which uses injectors and Class B which uses heat exchange coils. Style 2 is an electrically heated dishwashing machine. Style 3 on the other hand is gas heated with two classes namely Class C which uses natural gas and Class D which uses LP gas. In addition, these dishwashing machines can be classified into three groups according to size and capacity: Group A, Group B, and Group C. Materials used in the manufacture of these machines shall consist of corrosion-resistant steel, corrosion resisting material, nickel-copper alloy and plastics. The dishwashing machine shall be complete so that when connected to the specified source of power, water supply, heating means (steam, electric, or gas), drainage, detergent, and rinse agent feeder as applicable, the unit can be used for its intended function. Dishwashers shall be rigid, quiet in operation, free from objectionable vibration, and so constructed as to prevent objectionable splashing of water to the outside of the machine. Operational test, leakage test, and performance profiles shall be done in order to determine the overall efficiency of the dishwashing machine.
SCOPE
1.1 This specification covers multiple tank, automatic rackless conveyor type, commercial dishwashing machines.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are provided for information only.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers single tank, automatic rack type, hot water sanitizing commercial dishwashing machines. Covered by this specification are dishwashing machines of various types (Types I and II based on feed direction, from right or left, respectively), styles (Styles 1-3 based on method of heating: steam, electric, or gas), classes (Classes A-D based on heat source: injector, heat exchange coil, natural gas, or LP gas), sizes, and capacities. Components comprising the dishwashing machine shall be manufactured from corrosion-resistant steel (tank, scrap trays or strainers, overflow drain, access door/s, and legs), corrosion-resisting materials (conveyor, piping and fittings, valves, and spray assemblies), nickel-copper alloys, and plastics. Pump casings shall be of cast iron or corrosion-resisting material. When specified, the dishwashing machine assembly may include a final rinse booster, detergent feeder, and rinse agent feeder. The dishwashing machine shall be tested for performance standards compliance and noise level as well as for operational, leakage, and performance profile requirements. All tests shall comply with the requirements specified.
SCOPE
1.1 This specification covers single tank, automatic rack type, commercial dishwashing machines.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the material, design, and performance requirements pertinent to the construction of water-driven rotary spray type, stationary rack commercial pot, pan, and utensil washing machines that are manually fed yet automatically controlled to uniformly wash, rinse, and heat-sanitize food preparation utensils. Representative production models of the washers shall pass performance, operation, leakage, and energy and productivity tests, and should function satisfactorily as specified. Certification, product marking, and packaging are also considered.
SCOPE
1.1 This specification covers manually fed, spray-type stationary rack, automatically controlled, water-driven rotary spray commercial pot, pan, and utensil washing machines, herein referred to as “the washer.”  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers manually fed, motor-driven rotary conveyor type, automatically controlled, commercial pot, pan, and utensil washing machines. The washer shall be of the following type, and class as specified. Motor-driven continuous rotary conveyor: type I - one door (front loading); type II - one or two door (pass-through corner operation); and type III - one or two door (pass-through straight line operation). Style and class: style 1 - steam heated; style 2 - electric heat; class A - injection; and class B - heat exchange coil. The design, construction, and performance requirements of the washing machine are presented in details. The operational test; leakage test; and energy and productivity test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers manually fed, motor-driven rotary conveyor type, automatically controlled, commercial pot, pan, and utensil washing machines, hereinafter referred to as “the washer.”  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary statement pertains only to the test methods portion, Section 9 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the requirements for manually fed, motor-driven vertically oscillating arm type, automatically controlled, commercial pot, pan, and utensil washing machine (also referred to as "the washer"). The washer is of one rack capacity (Type I) and is available in either Style A (one door/front loading) or Style B (three door/pass-through with front load door). Heat shall be provided to the washer through steam (Style 1) by injection (Class A) or heat exchange coil (Class B) or through electric means (Style 2). The washer and its components shall be manufactured free of defects. Piping and fittings shall be manufactured from corrosion-resisting material or heat-resisting plastic material. Valves, spray assemblies, and overflow drain shall be manufactured from corrosion-resisting materials. Tank and housing shall be constructed of corrosion-resistant steel. Scrap trays (strainers), access door/s, and legs shall be constructed of corrosion-resistant steel or other corrosion-resisting material. The pump motor shall be mounted on the tank or rigid steel base, with the pump casing being of cast iron or corrosion-resisting material. When specified, a final rinse booster heater and/or detergent feeder may be provided. The washer shall be operated at ambient room temperature. Tests for performance standards and operational compliance as well as for noise level, leakage, energy, and productivity requirements shall be performed and shall conform to the requirements specified.
SCOPE
1.1 This specification covers manually fed, motor-driven vertically oscillating arm type, automatically controlled, commercial pot, pan, and utensil washing machines, hereinafter referred to as “the washer.”  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary statement pertains only to the test methods portion, Section 9 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification establishes the material, design, and performance requirements pertinent to the construction of commercial pulping and waterpress assemblies that are intended for grinding food scraps, paper, cardboard, and disposable plastic food-service ware. Unless otherwise specified, materials used to fabricate pulpers and waterpresses may include corrosion-resistant steel and other corrosion-resisting materials, abrasion-resistant cast iron, austenitic gray iron, copper tube, brass pipe, alloy steel, black and galvanized pipe, gaskets and seals, perforated metal, stainless steel pipe, plastic piping and fitting, and austenitic gray iron pipe fitting. Assembled pulpers and waterpresses shall meet operational, electrical, lubrication, finish, and performance requirements, and should function satisfactorily as specified.
SCOPE
1.1 This specification covers commercial pulping and waterpress assemblies intended for grinding of food scraps, paper, cardboard, and disposable plastic food-service ware.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test method portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification applies to dehydrators intended for removing liquid by evaporation from processed or unprocessed food scraps and limited amounts of cardboard, paper, and biodegradable food service ware. Dehydrators shall be of the following type, size, and options as specified:
Type A-Capable of processing up to 140 lb (63.6 kg) per day.
Type B-Capable of processing 141 to 240 lb (64.1 to 109.1 kg) per day.
Type C-Capable of processing 250 lb (113.6 kg) per day.
Type D-Capable of processing 650 lb (295.4 kg) per day.
Type E-Capable of processing 900 to 1100 lb (40.9 to 500 kg) per day.
Type F-Capable of processing 2200 lb (1000 kg) per day.
Type G-Capable of processing 3300 lb (1500 kg) per day.
All equipment of the same model designation and options on the same purchase order shall have component interchangeability for serviceability.
This specification includes requirements for materials to be used in the fabrication of dehydrators as well as their design and construction, operation, electrical properties, lubrication, finish, and performance. It also covers test methods, certification, product marking, information to be supplied in the manuals (installation instructions, operating guide, maintenance procedures, service parts list, electrical schematics), packaging and packing materials, and quality assurance.
SCOPE
1.1 This specification covers dehydrators intended for removing liquid by evaporation from processed or unprocessed food scraps and limited amounts of cardboard, paper, and biodegradable food service ware.  
1.2 The values as stated in inch-pound units are to be regarded as the standard. The values stated in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test method portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers multiple tank automatic rack-type commercial dishwashing machines. Dishwashing machines shall be of the following types, styles, and classes, as specified: Type I-this machine shall be designed and supplied to accept the feeding of soiled tableware from the right side, when facing the front of the machine; and Type II-this machine shall be designed and supplied to accept the feeding of soiled tableware from the left side, when facing the front of the machine. Style 1 - steam heated; Style 2 - electrically heated; Style 3 - gas-heated; and Style 4 - pre-wash unit. Class A - injectors; Class B - heat exchange coils; Class C - natural gas; and Class D - LP gas. The construction requirements; electrical, steam and gas equipment requirements; lubrication requirements; treatment and painting requirements; and performance requirements are presented in details.
SCOPE
1.1 This specification covers multiple tank automatic rack-type commercial dishwashing machines.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ABSTRACT
This specification covers commercial powered pot, pan, and utensil washing sinks of the following types, styles, and classes: Type I, Type II, Style 1 (Class A and Class B), and Style 2, having the specified sizes for (1) drainboards, soiled and clean ends, (2) scrapper section, (3) wash sink, (4) rinse sink, and (5) sanitizer sink. The materials shall conform to the specified requirements and include: corrosion-resistant steel, corrosion-resisting material, nickel-copper alloy, and plastics. Construction requirements for the following are detailed: (1) piping, tubing, fittings, and valves, (2) spray assemblies, (3) tank, (4) overflow, (5) frame, (6) legs (feet), (7) pump and motor assemblies, and (8) heating. The electrical equipment requirements for the motors, controls, and wiring and circuit devices; lubrication requirements; and requirements for treatment and painting, are specified. Powered pot, pan, and utensil washing sinks shall conform to the specified performance requirements including noise level. Operational, leakage, and performance tests shall be performed.
SCOPE
1.1 This specification covers commercial powered pot, pan and utensil washing sinks.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers racks used in commercial spray type dishwashing machines and for storage of clean tableware. Commercial dishwashing racks shall be classified as follows: Type I (Types IA, IB, IC, ID, IE, and IF); Type II (Type IIA, IIB, IIC, IID, and IIE); Type III; Type IV; Type V; and Type VI. Impact test, bow test, visual examination, and dimensional examination shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification covers racks used in commercial spray type dishwashing machines and for storage of clean tableware.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazard caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers pulper assemblies intended for grinding of food scraps and limited amounts of cardboard, paper, and disposable plastic food service wear. Pulper assemblies shall be of the following types: Type A and Type B. Lubricating points shall be readily accessible, and the pulper shall be lubricated with the proper amount of lubricant prior to delivery. All surfaces of the machine, other than corrosion-resistant materials, shall be protected against corrosion in the use environment and shall present a neat appearance. Test method shall be performed to demonstrate the ability of the unit to meet the capacity requirements and to insure that there is no leakage during operation.
SCOPE
1.1 This specification covers pulper assemblies intended for grinding of food scraps and limited amounts of cardboard, paper, and disposable plastic food service ware.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test method portion, Section 13, of this specification:  
1.4 This standard does not purport to address all of the safety concerns, if, any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers manually fed, spray-type, stationary rack, automatically controlled, dump type, chemical sanitizing commercial dishwashing machines. Dishwashing machines shall be of the following types, styles, classes: type I - Straight-through model, 34 in. nominal table height. This machine is used in line with table on each side, type II - Corner model, 34 in. nominal table height. This machine is used in corner placement forming a 90� table on each side, and type III - Under counter, front load. This machine may be installed under counters; style A - single rack, and style B - double rack. No leakage shall occur when tested at pressures up to 125 % of the manufacturer's recommended supply line pressure. The dishwasher materials, construction, operation cycle, electrical equipment, lubrication, and coating shall meet the requirements prescribed.
SCOPE
1.1 This specification covers manually fed, spray-type, stationary rack, automatically controlled, dump type, chemical sanitizing commercial dishwashing machines.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ABSTRACT
This specification covers commercial food waste disposers intended for the grinding of food waste. Commercial disposers shall be of two types, namely: Type and Type II. The materials shall conform to the specified requirements and include the following: corrosion resistant steel, aluminum alloy, abrasion-resistant cast iron, austenitic gray iron, copper tube, brass pipe, alloy steel, black and galvanized pipe, and gaskets and seals. The disposer construction requirements including requirements for the following are detailed: (1) valves and fittings, (2) hopper (upper housing), (3) grind chamber (lower housing), (4) shredded ring, (5) flywheel, (6) cutting teeth, (7) water seal, (8) bearings, (9) motor, (10) wiring and circuit protective devices, (11) support leg(s), and (12) plating, coating, and painting. Leakage and operations test shall be performed.
SCOPE
1.1 This specification covers commercial food waste disposers intended for the grinding of food waste.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ABSTRACT
This specification covers racks used in commercial spray type dishwashing machines and for storage of clean tableware. Commercial dishwashing racks shall be classified as follows: Type I (Types IA, IB, IC, ID, IE, and IF); Type II (Type IIA, IIB, IIC, IID, and IIE); Type III; Type IV; Type V; and Type VI. Impact test, bow test, visual examination, and dimensional examination shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification covers racks used in commercial spray type dishwashing machines and for storage of clean tableware.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazard caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers pulper assemblies intended for grinding of food scraps and limited amounts of cardboard, paper, and disposable plastic food service wear. Pulper assemblies shall be of the following types: Type A and Type B. Lubricating points shall be readily accessible, and the pulper shall be lubricated with the proper amount of lubricant prior to delivery. All surfaces of the machine, other than corrosion-resistant materials, shall be protected against corrosion in the use environment and shall present a neat appearance. Test method shall be performed to demonstrate the ability of the unit to meet the capacity requirements and to insure that there is no leakage during operation.
SCOPE
1.1 This specification covers pulper assemblies intended for grinding of food scraps and limited amounts of cardboard, paper, and disposable plastic food service ware.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test method portion, Section 13, of this specification:  
1.4 This standard does not purport to address all of the safety concerns, if, any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers multiple tank, automatic rack less conveyor type, commercial dishwashing machines. These machines can be classified into two types: Type 1 machines shall be designed and supplied to accept the feeding of soiled tableware from the right side, when facing the front of the machine while Type II shall be designed and supplied to accept the feeding of soiled tableware from the left side, when facing the front of the machine. The dishwashing machines have three kinds of styles: Style 1 is a steam heated machine, with two classes namely Class A which uses injectors and Class B which uses heat exchange coils. Style 2 is an electrically heated dishwashing machine. Style 3 on the other hand is gas heated with two classes namely Class C which uses natural gas and Class D which uses LP gas. In addition, these dishwashing machines can be classified into three groups according to size and capacity: Group A, Group B, and Group C. Materials used in the manufacture of these machines shall consist of corrosion-resistant steel, corrosion resisting material, nickel-copper alloy and plastics. The dishwashing machine shall be complete so that when connected to the specified source of power, water supply, heating means (steam, electric, or gas), drainage, detergent, and rinse agent feeder as applicable, the unit can be used for its intended function. Dishwashers shall be rigid, quiet in operation, free from objectionable vibration, and so constructed as to prevent objectionable splashing of water to the outside of the machine. Operational test, leakage test, and performance profiles shall be done in order to determine the overall efficiency of the dishwashing machine.
SCOPE
1.1 This specification covers multiple tank, automatic rackless conveyor type, commercial dishwashing machines.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are provided for information only.

SCOPE
1.1 This specification covers single tank, automatic rack type, commercial dishwashing machines.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ABSTRACT
This specification covers detergent feeders, rinse additive feeders, and sanitizing agent feeders intended to automatically maintain the concentration of additives in the wash, recirculated rinse, or non-recirculated rinse water of commercial spray- type dish-washing and glass-washing machines. Detergent, rinse additive, and sanitizing agent feeders shall be of the following types and styles: Types I, II, III, IV, V, and VI; and Style I; II; III; IV; V; and VI. Materials used shall be free from defects that would adversely affect the performance or maintainability of individual components or of the overall assembly. The feeder shall be complete so that when connected to the specified source of power (electrical or water, or both), the unit can be used for its intended function. Feeders shall be tested in accordance with specified requirements.
SCOPE
1.1 This specification covers detergent feeders, rinse additive feeders, and sanitizing agent feeders intended to automatically maintain the concentration of additives in the wash, recirculated rinse, or non-recirculated rinse water of commercial spray-type dishwashing and glasswashing machines.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

ABSTRACT
This specification covers the material, design, and performance requirements pertinent to the construction of spray-type, stationary rack commercial dishwashing machines that are manually fed yet automatically controlled to uniformly wash, rinse, and sanitize eating and drinking utensils. Representative production models of the washers shall pass performance, operation, leakage, and energy and productivity tests, and should function satisfactorily as specified. Certification, product marking, and packaging are also considered.
SCOPE
1.1 This specification covers manually fed, spray-type, stationary rack, automatically controlled, hot water and chemical sanitizing commercial dishwashing machines.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following precautionary caveat pertains only to the test methods portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the requirements for manually fed, motor-driven vertically oscillating arm type, automatically controlled, commercial pot, pan, and utensil washing machine (also referred to as "the washer"). The washer is of one rack capacity (Type I) and is available in either Style A (one door/front loading) or Style B (three door/pass-through with front load door). Heat shall be provided to the washer through steam (Style 1) by injection (Class A) or heat exchange coil (Class B) or through electric means (Style 2). The washer and its components shall be manufactured free of defects. Piping and fittings shall be manufactured from corrosion-resisting material or heat-resisting plastic material. Valves, spray assemblies, and overflow drain shall be manufactured from corrosion-resisting materials. Tank and housing shall be constructed of corrosion-resistant steel. Scrap trays (strainers), access door/s, and legs shall be constructed of corrosion-resistant steel or other corrosion-resisting material. The pump motor shall be mounted on the tank or rigid steel base, with the pump casing being of cast iron or corrosion-resisting material. When specified, a final rinse booster heater and/or detergent feeder may be provided. The washer shall be operated at ambient room temperature. Tests for performance standards and operational compliance as well as for noise level, leakage, energy, and productivity requirements shall be performed and shall conform to the requirements specified.
SCOPE
1.1 This specification covers manually fed, motor-driven vertically oscillating arm type, automatically controlled, commercial pot, pan, and utensil washing machines, hereinafter referred to as “the washer.”
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following precautionary statement pertains only to the test methods portion, Section 9 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification establishes the material, design, and performance requirements pertinent to the construction of commercial pulping and waterpress assemblies that are intended for grinding food scraps, paper, cardboard, and disposable plastic food-service ware. Unless otherwise specified, materials used to fabricate pulpers and waterpresses may include corrosion-resistant steel and other corrosion-resisting materials, abrasion-resistant cast iron, austenitic gray iron, copper tube, brass pipe, alloy steel, black and galvanized pipe, gaskets and seals, perforated metal, stainless steel pipe, plastic piping and fitting, and austenitic gray iron pipe fitting. Assembled pulpers and waterpresses shall meet operational, electrical, lubrication, finish, and performance requirements, and should function satisfactorily as specified.
SCOPE
1.1 This specification covers commercial pulping and waterpress assemblies intended for grinding of food scraps, paper, cardboard, and disposable plastic food-service ware.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test method portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the material, design, and performance requirements pertinent to the construction of water-driven rotary spray type, stationary rack commercial pot, pan, and utensil washing machines that are manually fed yet automatically controlled to uniformly wash, rinse, and heat-sanitize food preparation utensils. Representative production models of the washers shall pass performance, operation, leakage, and energy and productivity tests, and should function satisfactorily as specified. Certification, product marking, and packaging are also considered.
SCOPE
1.1 This specification covers manually fed, spray-type stationary rack, automatically controlled, water-driven rotary spray commercial pot, pan, and utensil washing machines, herein referred to as “the washer.”
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers manually fed, motor-driven rotary conveyor type, automatically controlled, commercial pot, pan, and utensil washing machines. The washer shall be of the following type, and class as specified. Motor-driven continuous rotary conveyor: type I - one door (front loading); type II - one or two door (pass-through corner operation); and type III - one or two door (pass-through straight line operation). Style and class: style 1 - steam heated; style 2 - electric heat; class A - injection; and class B - heat exchange coil. The design, construction, and performance requirements of the washing machine are presented in details. The operational test; leakage test; and energy and productivity test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers manually fed, motor-driven rotary conveyor type, automatically controlled, commercial pot, pan, and utensil washing machines, hereinafter referred to as “the washer.”
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following precautionary statement pertains only to the test methods portion, Section 9 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers commercial powered pot, pan, and utensil washing sinks of the following types, styles, and classes: Type I, Type II, Style 1 (Class A and Class B), and Style 2, having the specified sizes for (1) drainboards, soiled and clean ends, (2) scrapper section, (3) wash sink, (4) rinse sink, and (5) sanitizer sink. The materials shall conform to the specified requirements and include: corrosion-resistant steel, corrosion-resisting material, nickel-copper alloy, and plastics. Construction requirements for the following are detailed: (1) piping, tubing, fittings, and valves, (2) spray assemblies, (3) tank, (4) overflow, (5) frame, (6) legs (feet), (7) pump and motor assemblies, and (8) heating. The electrical equipment requirements for the motors, controls, and wiring and circuit devices; lubrication requirements; and requirements for treatment and painting, are specified. Powered pot, pan, and utensil washing sinks shall conform to the specified performance requirements including noise level. Operational, leakage, and performance tests shall be performed.
SCOPE
1.1 This specification covers commercial powered pot, pan and utensil washing sinks.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers commercial multiple-tank dishwashing machines of the continuous type, oval shaped, with horizontal table conveyor systems. According to direction of rotation, the dishwashing machines can be classified into two types: Type I-CW (clockwise) rotation is designed and supplied to accept the feeding of soiled tableware from the right side, when viewed from above and Type II-CCW (counterclockwise) rotation is designed and supplied to accept the feeding of soiled tableware from the left side, when viewed from above. These dishwashing machines can also be classified into three styles: Style 1 is a steam heated machine, with two classes namely Class A which uses injectors and Class B which uses heat exchange coils. Style 2 is an electrically heated dishwashing machine. Style 3 on the other hand is gas heated with two classes namely Class C which uses natural gas and Class D which uses LP gas. Furthermore, four types of arrangements for these machines can be made: Arrangement A is with tray rail and table-mounted garbage disposal machine; Arrangement B is with food waste trough instead of tray rail and garbage disposal machine in center of trough; Arrangement C is the same as Arrangement A, except disposal unit is not available; and Arrangement D is the same as Arrangement B, except that there is no disposal unit. Materials used in the manufacture of these machines shall consist of corrosion-resistant steel, corrosion resisting material, nickel-copper alloy and plastics. These materials used shall be free from defects that would affect the performance or maintainability of individual components of the overall assembly. The dishwashing machine shall be complete so that when connected to the specified source of power, water supply, heating means (steam or electric) and drainage, detergent and rinse agent feeder as applicable, the unit can be used for its intended function. Dishwashers shall be quiet in operation, free from objectionable splashing of water to the outside of the machine. Operational test, leakage test, and performance profiles shall be done in order to determine the overall efficiency of the dishwashing machine.
SCOPE
1.1 This specification covers commercial multiple-tank dishwashing machines of the continuous type, oval shaped, with horizontal table conveyor systems.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to Section 12, Test Methods, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers multiple tank automatic rack-type commercial dishwashing machines. Dishwashing machines shall be of the following types, styles, and classes, as specified: Type I-this machine shall be designed and supplied to accept the feeding of soiled tableware from the right side, when facing the front of the machine; and Type II-this machine shall be designed and supplied to accept the feeding of soiled tableware from the left side, when facing the front of the machine. Style 1 - steam heated; Style 2 - electrically heated; Style 3 - gas-heated; and Style 4 - pre-wash unit. Class A - injectors; Class B - heat exchange coils; Class C - natural gas; and Class D - LP gas. The construction requirements; electrical, steam and gas equipment requirements; lubrication requirements; treatment and painting requirements; and performance requirements are presented in details.
SCOPE
1.1 This specification covers multiple tank automatic rack-type commercial dishwashing machines.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ABSTRACT
This specification covers manually fed, spray-type, stationary rack, automatically controlled, dump type, chemical sanitizing commercial dishwashing machines. Dishwashing machines shall be of the following types, styles, classes: type I - Straight-through model, 34 in. nominal table height. This machine is used in line with table on each side, type II - Corner model, 34 in. nominal table height. This machine is used in corner placement forming a 90° table on each side, and type III - Under counter, front load. This machine may be installed under counters; style A - single rack, and style B - double rack. No leakage shall occur when tested at pressures up to 125 % of the manufacturer's recommended supply line pressure. The dishwasher materials, construction, operation cycle, electrical equipment, lubrication, and coating shall meet the requirements prescribed.
SCOPE
1.1 This specification covers manually fed, spray-type, stationary rack, automatically controlled, dump type, chemical sanitizing commercial dishwashing machines.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ABSTRACT
This specification covers racks used in commercial spray type dishwashing machines and for storage of clean tableware. Commercial dishwashing racks shall be classified as follows: Type I (Types IA, IB, IC, ID, IE, and IF); Type II (Type IIA, IIB, IIC, IID, and IIE); Type III; Type IV; Type V; and Type VI. Impact test, bow test, visual examination, and dimensional examination shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification covers racks used in commercial spray type dishwashing machines and for storage of clean tableware.
1.2 The following safety hazard caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers commercial food waste disposers intended for the grinding of food waste. Commercial disposers shall be of two types, namely: Type and Type II. The materials shall conform to the specified requirements and include the following: corrosion resistant steel, aluminum alloy, abrasion-resistant cast iron, austenitic gray iron, copper tube, brass pipe, alloy steel, black and galvanized pipe, and gaskets and seals. The disposer construction requirements including requirements for the following are detailed: (1) valves and fittings, (2) hopper (upper housing), (3) grind chamber (lower housing), (4) shredded ring, (5) flywheel, (6) cutting teeth, (7) water seal, (8) bearings, (9) motor, (10) wiring and circuit protective devices, (11) support leg(s), and (12) plating, coating, and painting. Leakage and operations test shall be performed.
SCOPE
1.1 This specification covers commercial food waste disposers intended for the grinding of food waste.

ABSTRACT
This specification covers pulper assemblies intended for grinding of food scraps and limited amounts of cardboard, paper, and disposable plastic food service wear. Pulper assemblies shall be of the following types: Type A and Type B. Lubricating points shall be readily accessible, and the pulper shall be lubricated with the proper amount of lubricant prior to delivery. All surfaces of the machine, other than corrosion-resistant materials, shall be protected against corrosion in the use environment and shall present a neat appearance. Test method shall be performed to demonstrate the ability of the unit to meet the capacity requirements and to insure that there is no leakage during operation.
SCOPE
1.1 This specification covers pulper assemblies intended for grinding of food scraps and limited amounts of cardboard, paper, and disposable plastic food service wear.
1.2 The values as stated in inch-pound units are to be regarded as the standard. The values stated in parentheses are provided for information only.
1.3 The following safety hazards caveat pertains only to the test method portion, Section 13, of this specification:
1.4 This standard does not purport to address all of the safety concerns, if, any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers single tank, automatic rack type, hot water sanitizing commercial dishwashing machines. Covered by this specification are dishwashing machines of various types (Types I and II based on feed direction, from right or left, respectively), styles (Styles 1-3 based on method of heating: steam, electric, or gas), classes (Classes A-D based on heat source: injector, heat exchange coil, natural gas, or LP gas), sizes, and capacities. Components comprising the dishwashing machine shall be manufactured from corrosion-resistant steel (tank, scrap trays or strainers, overflow drain, access door/s, and legs), corrosion-resisting materials (conveyor, piping and fittings, valves, and spray assemblies), nickel-copper alloys, and plastics. Pump casings shall be of cast iron or corrosion-resisting material. When specified, the dishwashing machine assembly may include a final rinse booster, detergent feeder, and rinse agent feeder. The dishwashing machine shall be tested for performance standards compliance and noise level as well as for operational, leakage, and performance profile requirements. All tests shall comply with the requirements specified.
SCOPE
1.1 This specification covers single tank, automatic rack type, commercial dishwashing machines.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard

ABSTRACT
This specification covers the material, design, and performance requirements pertinent to the construction of spray-type, stationary rack commercial dishwashing machines that are manually fed yet automatically controlled to uniformly wash, rinse, and sanitize eating and drinking utensils. Representative production models of the washers shall pass performance, operation, leakage, and energy and productivity tests, and should function satisfactorily as specified. Certification, product marking, and packaging are also considered.
SCOPE
1.1 This specification covers manually fed, spray-type, stationary rack, automatically controlled, commercial dishwashing machines.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard

ABSTRACT
This specification covers commercial powered pot, pan, and utensil washing sinks of the following types, styles, and classes: Type I, Type II, Style 1 (Class A and Class B), and Style 2, having the specified sizes for (1) drainboards, soiled and clean ends, (2) scrapper section, (3) wash sink, (4) rinse sink, and (5) sanitizer sink. The materials shall conform to the specified requirements and include: corrosion-resistant steel, corrosion-resisting material, nickel-copper alloy, and plastics. Construction requirements for the following are detailed: (1) piping, tubing, fittings, and valves, (2) spray assemblies, (3) tank, (4) overflow, (5) frame, (6) legs (feet), (7) pump and motor assemblies, and (8) heating. The electrical equipment requirements for the motors, controls, and wiring and circuit devices; lubrication requirements; and requirements for treatment and painting, are specified. Powered pot, pan, and utensil washing sinks shall conform to the specified performance requirements including noise level. Operational, leakage, and performance tests shall be performed.
SCOPE
1.1 This specification covers commercial powered pot, pan and utensil washing sinks.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers multiple tank, automatic rack less conveyor type, commercial dishwashing machines. These machines can be classified into two types: Type 1 machines shall be designed and supplied to accept the feeding of soiled tableware from the right side, when facing the front of the machine while Type II shall be designed and supplied to accept the feeding of soiled tableware from the left side, when facing the front of the machine. The dishwashing machines have three kinds of styles: Style 1 is a steam heated machine, with two classes namely Class A which uses injectors and Class B which uses heat exchange coils. Style 2 is an electrically heated dishwashing machine. Style 3 on the other hand is gas heated with two classes namely Class C which uses natural gas and Class D which uses LP gas. In addition, these dishwashing machines can be classified into three groups according to size and capacity: Group A, Group B, and Group C. Materials used in the manufacture of these machines shall consist of corrosion-resistant steel, corrosion resisting material, nickel-copper alloy and plastics. The dishwashing machine shall be complete so that when connected to the specified source of power, water supply, heating means (steam, electric, or gas), drainage, detergent, and rinse agent feeder as applicable, the unit can be used for its intended function. Dishwashers shall be rigid, quiet in operation, free from objectionable vibration, and so constructed as to prevent objectionable splashing of water to the outside of the machine. Operational test, leakage test, and performance profiles shall be done in order to determine the overall efficiency of the dishwashing machine.
SCOPE
1.1 This specification covers multiple tank, automatic rackless conveyor type, commercial dishwashing machines.
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are provided for information only.

ABSTRACT
This specification covers detergent feeders, rinse additive feeders, and sanitizing agent feeders intended to automatically maintain the concentration of additives in the wash, recirculated rinse, or non-recirculated rinse water of commercial spray- type dish-washing and glass-washing machines. Detergent, rinse additive, and sanitizing agent feeders shall be of the following types and styles: Types I, II, III, IV, V, and VI; and Style I; II; III; IV; V; and VI. Materials used shall be free from defects that would adversely affect the performance or maintainability of individual components or of the overall assembly. The feeder shall be complete so that when connected to the specified source of power (electrical or water, or both), the unit can be used for its intended function. Feeders shall be tested in accordance with specified requirements.
SCOPE
1.1 This specification covers detergent feeders, rinse additive feeders, and sanitizing agent feeders intended to automatically maintain the concentration of additives in the wash, recirculated rinse, or non-recirculated rinse water of commercial spray-type dishwashing and glasswashing machines.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.