ASTM G39-99(2021)
(Practice)Standard Practice for Preparation and Use of Bent-Beam Stress-Corrosion Test Specimens
Standard Practice for Preparation and Use of Bent-Beam Stress-Corrosion Test Specimens
SIGNIFICANCE AND USE
5.1 The bent-beam specimen is designed for determining the stress-corrosion behavior of alloy sheets and plates in a variety of environments. The bent-beam specimens are designed for testing at stress levels below the elastic limit of the alloy. For testing in the plastic range, U-bend specimens should be employed (see Practice G30). Although it is possible to stress bent-beam specimens into the plastic range, the stress level cannot be calculated for plastically-stressed three- and four-point loaded specimens as well as the double-beam specimens. Therefore, the use of bent-beam specimens in the plastic range is not recommended for general use.
SCOPE
1.1 This practice covers procedures for designing, preparing, and using bent-beam stress-corrosion specimens.
1.2 Different specimen configurations are given for use with different product forms, such as sheet or plate. This practice is applicable to specimens of any metal that are stressed to levels less than the elastic limit of the material, and therefore, the applied stress can be accurately calculated or measured (see Note 1). Stress calculations by this practice are not applicable to plastically stressed specimens.
Note 1: It is the nature of these practices that only the applied stress can be calculated. Since stress-corrosion cracking is a function of the total stress, for critical applications and proper interpretation of results, the residual stress (before applying external stress) or the total elastic stress (after applying external stress) should be determined by appropriate nondestructive methods, such as X-ray diffraction (1).2
1.3 Test procedures are given for stress-corrosion testing by exposure to gaseous and liquid environments.
1.4 The bent-beam test is best suited for flat product forms, such as sheet, strip, and plate. For plate material the bent-beam specimen is more difficult to use because more rugged specimen holders must be built to accommodate the specimens. A double-beam modification of a four-point loaded specimen to utilize heavier materials is described in 10.5.
1.5 The exposure of specimens in a corrosive environment is treated only briefly since other practices deal with this aspect, for example, Practices D1141, G30, G36, G44, G50, and G85. The experimenter is referred to ASTM Special Technical Publication 425 (2).
1.6 The bent-beam practice generally constitutes a constant strain (deflection) test. Once cracking has initiated, the state of stress at the tip of the crack as well as in uncracked areas has changed, and therefore, the known or calculated stress or strain values discussed in this practice apply only to the state of stress existing before initiation of cracks.
1.7 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (For more specific safety hazard information see Section 7 and 12.1.)
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: G39 −99 (Reapproved 2021)
Standard Practice for
Preparation and Use of Bent-Beam Stress-Corrosion Test
Specimens
ThisstandardisissuedunderthefixeddesignationG39;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope stress at the tip of the crack as well as in uncracked areas has
changed,andtherefore,theknownorcalculatedstressorstrain
1.1 This practice covers procedures for designing,
valuesdiscussedinthispracticeapplyonlytothestateofstress
preparing, and using bent-beam stress-corrosion specimens.
existing before initiation of cracks.
1.2 Differentspecimenconfigurationsaregivenforusewith
1.7 The values stated in SI units are to be regarded as
different product forms, such as sheet or plate. This practice is
standard. The values given in parentheses after SI units are
applicable to specimens of any metal that are stressed to levels
providedforinformationonlyandarenotconsideredstandard.
less than the elastic limit of the material, and therefore, the
1.8 This standard does not purport to address all of the
applied stress can be accurately calculated or measured (see
safety concerns, if any, associated with its use. It is the
Note 1). Stress calculations by this practice are not applicable
responsibility of the user of this standard to establish appro-
to plastically stressed specimens.
priate safety, health, and environmental practices and deter-
NOTE 1—It is the nature of these practices that only the applied stress
mine the applicability of regulatory limitations prior to use.
canbecalculated.Sincestress-corrosioncrackingisafunctionofthetotal
(For more specific safety hazard information see Section 7 and
stress, for critical applications and proper interpretation of results, the
residual stress (before applying external stress) or the total elastic stress 12.1.)
(after applying external stress) should be determined by appropriate
1.9 This international standard was developed in accor-
nondestructive methods, such as X-ray diffraction (1).
dance with internationally recognized principles on standard-
1.3 Test procedures are given for stress-corrosion testing by
ization established in the Decision on Principles for the
exposure to gaseous and liquid environments.
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
1.4 The bent-beam test is best suited for flat product forms,
Barriers to Trade (TBT) Committee.
suchassheet,strip,andplate.Forplatematerialthebent-beam
specimen is more difficult to use because more rugged speci-
2. Referenced Documents
men holders must be built to accommodate the specimens. A
double-beam modification of a four-point loaded specimen to 2.1 ASTM Standards:
utilize heavier materials is described in 10.5. D1141Practice for the Preparation of Substitute Ocean
Water
1.5 The exposure of specimens in a corrosive environment
G30 Practice for Making and Using U-Bend Stress-
is treated only briefly since other practices deal with this
Corrosion Test Specimens
aspect, for example, Practices D1141, G30, G36, G44, G50,
G36Practice for Evaluating Stress-Corrosion-Cracking Re-
and G85. The experimenter is referred to ASTM Special
sistance of Metals and Alloys in a Boiling Magnesium
Technical Publication 425 (2).
Chloride Solution
1.6 The bent-beam practice generally constitutes a constant
G44PracticeforExposureofMetalsandAlloysbyAlternate
strain (deflection) test. Once cracking has initiated, the state of
Immersion in Neutral 3.5 % Sodium Chloride Solution
G50Practice for Conducting Atmospheric Corrosion Tests
This practice is under the jurisdiction ofASTM Committee G01 on Corrosion
on Metals
of Metals and is the direct responsibility of Subcommittee G01.06 on Environmen-
tally Assisted Cracking.
Current edition approved May 1, 2021. Published May 2021. Originally
approvedin1973.Lastpreviouseditionapprovedin2016asG39–99(2016).DOI: For referenced ASTM standards, visit the ASTM website, www.astm.org, or
10.1520/G0039-99R21. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
The boldface numbers in parentheses refer to a list of references at the end of Standards volume information, refer to the standard’s Document Summary page on
this standard. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
G39 − 99 (2021)
G85Practice for Modified Salt Spray (Fog) Testing
2.2 NACE Document:
NACE TM0177-96Laboratory Testing of Metals for Resis-
tancetoSpecificFormsofEnvironmentalCrackinginH S
Environments
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 cracking time—the time elapsed from the inception of
test until the appearance of cracking.
3.1.1.1 Discussion—The test begins when the stress is
applied and the stressed specimen is exposed to the corrosive
environment, whichever occurs later.
3.1.1.2 Discussion—The specimen is considered to have
failed when cracks are detected. Presence of cracks can be
determined with or without optical, mechanical, or electronic
aids. However, for meaningful interpretation, comparisons
should be made only among tests employing crack detection
methods of equivalent sensitivity.
3.1.2 stress-corrosion cracking—a cracking process requir-
ingthesimultaneousactionofacorrodentandsustainedtensile
stress. This excludes corrosion-reduced sections that fail by
fastfracture.Italsoexcludesintercrystallineortranscrystalline
corrosion which can disintegrate an alloy without either
applied or residual stress.
4. Summary of Practice
4.1 This practice involves the quantitative stressing of a
beamspecimenbyapplication of a bending stress.Theapplied
stress is determined from the size of the specimen and the
FIG. 1 Schematic Specimen and Holder Configurations
bendingdeflection.Thestressedspecimensthenareexposedto
the test environment and the time required for cracks to
developisdetermined.Thiscrackingtimeisusedasameasure
NOTE 2—The double-beam specimen, more fully described in 10.5,is
of the stress-corrosion resistance of the material in the test
self-contained and does not require a holder.
environment at the stress level utilized.
NOTE 3—Specimen holders can be modified from the constant defor-
mation type shown in Fig. 1 to give a constant-load type of stressing. For
5. Significance and Use
instance, the loading bolt can be supplanted by a spring or deadweight
arrangement to change the mode of loading.
5.1 The bent-beam specimen is designed for determining
6.1.1 The holder shall be made of a material that would
the stress-corrosion behavior of alloy sheets and plates in a
withstand the influence of the environment without deteriora-
variety of environments. The bent-beam specimens are de-
tion or change in shape.
signed for testing at stress levels below the elastic limit of the
alloy.Fortestingintheplasticrange,U-bendspecimensshould
NOTE4—Itshouldberecognizedthatmanyplasticstendtocreepwhen
be employed (see Practice G30). Although it is possible to
subjectedtosustainedloads.Ifspecimenholdersorinsulatorsaremadeof
suchmaterials,theappliedstressonthespecimenmaychangeappreciably
stress bent-beam specimens into the plastic range, the stress
with time. By proper choice of holder and insulator materials, however,
level cannot be calculated for plastically-stressed three- and
many plastics can be used, especially in short-time tests.
four-point loaded specimens as well as the double-beam
6.1.2 Whenthestress-corrosiontestisconductedbyimmer-
specimens. Therefore, the use of bent-beam specimens in the
sion in an electrolyte, galvanic action between specimen and
plastic range is not recommended for general use.
holder (or spacer) shall be prevented (see Note 5). This is
accomplishedby(1)makingtheholderofthesamematerialas
6. Apparatus
the individual specimens, (2) inserting electrically insulating
6.1 Specimen Holders—Bent-beam specimens require a
materials between specimen and holder at all points of contact
specimen holder for each specimen, designed to retain the
(see Note 4), (3) making the entire holder out of a nonmetallic
applied stress on the specimen. Typical specimen holder
material (see Note 4), or (4) coating the holder with an
configurations are shown schematically in Fig. 1.
electrically nonconducting coating that effectively prevents
contact between holder and electrolyte.
6.1.3 Crevice corrosion may occur in an electrolyte at
AvailablefromNACEInternational(NACE),15835ParkTenPl.,Houston,TX
77084, http://www.nace.org. contact points between specimen and holder (or spacer). In
G39 − 99 (2021)
these instances the critical areas should be packed with a
hydrophobic filler (such as grease or wax).
NOTE 5—In atmospheres (gas) galvanic action between specimen and
holder either does not exist or is confined to a very small area as
experienced in outdoor exposure tests.
6.2 StressingJigs—Three-pointandfour-pointloadedspeci-
men holders, Fig. 1(b and c), contain a stressing feature in the
form of a loading screw.To stress two-point loaded specimens
(Fig. 1(a)), a separate stressing jig shall be used.Aconvenient
stressing jig is shown in Fig. 2.
NOTE 6—The double-beam specimen, described in 10.5, requires a
mechanical or hydraulic stressing frame (a universal tension testing
machine can also be used) as well as welding equipment.
6.3 Deflection Gauges—Deflection of specimens is deter-
mined by separate gages or by gages incorporated in a loading
FIG. 3 Specimen Loading Apparatus for Three-Point Loaded
apparatus as shown in Fig. 3. In designing a deflection gage to
Beam Specimens with Integral Deflection Gage
suit individual circumstances care must be taken to reference
the deflection to the proper support distance as defined in 10.2
– 10.5.
anticipatedloadingdirectioninservicewithrespecttoprocess-
7. Hazards
ing conditions, for example, rolling direction.
7.1 Bent-beam specimens made from high-strength materi-
8.2 Paragraphs 9.4 and 9.5 deal specifically with specimen
alsmayexhibithighratesofcrackpropagationandaspecimen
selection as related to the original material surface.
may splinter into several pieces. Due to high stresses in a
specimen,thesepiecesmayleavethespecimenathighvelocity
9. Test Specimen
and can be dangerous. Personnel installing and examining
9.1 The bent-beam, stress-corrosion specimens shall be flat
specimens should be cognizant of this possibility and be
strips of metal of uniform, rectangular cross section, and
protected against injury.
uniform thickness.
9.2 The identification of individual specimens should be
8. Sampling
permanentlyinscribedateachendofthespecimenbecausethis
8.1 Test specimens shall be selected so that they represent
is the area of lowest stress and cracking is not expected to be
the material to be tested. In simulating a service condition, the
initiatedbytheidentificationmarkings.Ifstencilingisusedfor
directionofloadapplicationinthespecimenshallrepresentthe
identification, this shall be done only on softened material
beforeanyhardeningheattreatmentstopreventcrackinginthe
stenciled area. Care must be taken to prevent the identification
from being obliterated by corrosion.
9.3 Mechanical properties should be determined on the
sameheat-treatmentlotfromwhichstress-corrosionspecimens
are obtained.
9.4 The specimens can be cut from sheet or plate in such a
fashion that the original material surface is retained. This
procedure is recommended when it is desired to include the
effect of surface condition in the test.
9.5 If, however, it is desired that surface conditions should
not influence the test results of several materials with different
surface conditions, the surfaces of all specimens must be
prepared in the same way. It is recommended that grinding or
machiningtoasurfacefinishofatleast0.7µm(30µin.)andto
a depth of at least 0.25 mm (0.01 in.) be utilized for surface
preparation. It is desirable to remove the required amount of
metalinseveralstepsbyalternatelygrindingoppositesurfaces.
This practice minimizes warpage due to residual stresses
caused by machining.All edges should be similarly ground or
machined to remove cold-worked material from previous
shearing. Chemical or electrochemical treatments that produce
FIG. 2 Stressing Jig and Two-Point Loaded Specimen with Holder
(approximately ⁄4 actual size) hydrogen on the specimen surface must not be used on
G39 − 99 (2021)
materials that may be subject to embrittlement by hydrogen or where:
that react with hydrogen to form a hydride.
L = length of specimen,
H = distance between supports (holder span),
9.6 Immediately before stressing, the specimens should be
t = thickness of specimen,
degreased and cleaned to remove contamination that occurred
ε = maximum tensile strain,
during specimen preparation. Only chemicals appropriate for
π/2
K = 2 −1/2
*
thegivenmetaloralloyshouldbeused.Caremustbeexercised ~1 2 k sin z) dz(completeellipticintegralofthe
nottocontaminatecleanedspecimens.Also,itissuggestedthat
first kind),
π/2
specimens be examined for cracks before exposure to the test
E =
2 1/2
* 1 2 k sin z) dz (complete elliptic integral of the
~
environment.
second kind),
10. Stress Calculations
k = sin θ/2,
10.1 The equations given in this section are valid only for θ = maximum slope of the specimen, that is, at the end of
stresses below the elastic limit of the material. At stresses the specimen, and
z = integration parameter (3).
abovetheelasticlimit,butbelowtheengineeringyieldstrength
(0.2% offset) only a small error results from use of the
10.2.2 The mathematical analysis establishes that Eq 1 and
equations (see Note 1). The equations must not be used above
Eq2definetherelationshipbetweenthestrainεand(L−H)⁄H
the yield strength of the material. The following paragraphs
in parameter form. The common parameter in these equations
give relationships used to calculate the maximum longitudinal
is the modulus k of the elliptic integrals. Thus, the following
stress in the outer fibers of the specimen convex surface.
procedure can be used to determine the specimen length L that
Calculations for transverse stress or edge-to-edge variation of
is required to produce a given maximum stress σ:
longitudinal stress are not given; the specimen dimensions are
10.2.2.1 Divide the stress σ by the modulus of elasticity E
m
chosen to m
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.