ASTM C1396/C1396M-09a
(Specification)Standard Specification for Gypsum Board
Standard Specification for Gypsum Board
ABSTRACT
This specification covers gypsum boards which include the following: gypsum wallboard for use on walls, ceilings, or partitions and that affords a surface suitable to receive decoration; predecorated gypsum board for use as the finished surfacing for walls, ceilings, or partitions; gypsum backing board, coreboard, and shaftliner board for use as a base in multilayer systems or as a gypsum stud or core in semisolid or solid gypsum board partitions, or in shaft wall assemblies; water-resistant gypsum backing board to be used as a base for the application of ceramic or plastic tile on walls or ceilings; exterior gypsum soffit board for exterior soffits and carport ceilings that are completely protected from contact with liquid water; gypsum sheathing board for use as sheathing on buildings; gypsum base for veneer plaster; gypsum lath for use as a base for gypsum plaster application; and gypsum ceiling board for interior ceilings and walls. Gypsum board shall consist of a noncombustible core, essentially gypsum, surfaced with paper bonded to the core. The specimens shall comply with the following required physical properties: core, end, and edge hardness; straightness of the edges and ends; length; tapered edge depth; flexural strength; humidified deflection; nail pull resistance; permeance; water resistance; and surface water absorption.
SCOPE
1.1 This specification covers the gypsum boards described in 1.1.1-1.1.9.
Note 1—Specifications C840, C841, C844 and C1280 contain application procedures for gypsum board.
1.1.1 Gypsum wallboard, designed for use on walls, ceilings, or partitions and that affords a surface suitable to receive decoration.
1.1.2 Predecorated gypsum board, designed for use as the finished surfacing for walls, ceilings, or partitions.
1.1.3 Gypsum backing board, coreboard, and shaftliner board, designed for use as a base in multilayer systems or as a gypsum stud or core in semisolid or solid gypsum board partitions, or in shaft wall assemblies.
Note 2—The terms backing board, coreboard, and shaftliner board refer to different end uses. The term gypsum backing board, as used in this specification, shall include gypsum coreboard and gypsum shaftliner board unless otherwise stated.
1.1.4 Water-resistant gypsum backing board, designed primarily to be used as a base for the application of ceramic or plastic tile on walls or ceilings. This product is also suitable for decoration.
1.1.5 Exterior gypsum soffit board, designed for use on exterior soffits and carport ceilings that are completely protected from contact with liquid water.
1.1.6 Gypsum sheathing board, designed for use as sheathing on buildings.
1.1.7 Gypsum base for veneer plaster, designed for use as a base for the application of gypsum veneer plaster.
1.1.8 Gypsum lath, designed for use as a base for the application of gypsum plaster.
1.1.9 Gypsum ceiling board, designed for use on interior ceilings with framing spaced not more than 24 in. [610 mm] on center and that affords a surface suitable to receive water-based texture and other decoration. This product is also suitable for use on interior walls.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1396/C1396M – 09a
Standard Specification for
1
Gypsum Board
This standard is issued under the fixed designation C1396/C1396M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.2 Specifications applicable to all gypsum boards are
located in Section 1-4 and 13-15. Specifications applicable to
1.1 This specification covers the gypsum boards described
specific gypsum boards are located in the following sections:
in 1.1.1-1.1.9.
Section
NOTE 1—Specifications C840, C841, C844 and C1280 contain appli-
Gypsum wallboard, predecorated gypsum board 5
cation procedures for gypsum board.
Gypsum backing board, gypsum coreboard, 6
gypsum shaftliner board
1.1.1 Gypsum wallboard, designed for use on walls, ceil-
Water-resistant gypsum backing board 7
Exterior gypsum soffit board 8
ings, or partitions and that affords a surface suitable to receive
Gypsum sheathing board 9
decoration.
Gypsum base for veneer plaster 10
1.1.2 Predecorated gypsum board, designed for use as the
Gypsum lath 11
Gypsum Ceiling Board 12
finished surfacing for walls, ceilings, or partitions.
1.1.3 Gypsum backing board, coreboard, and shaftliner
1.3 The values stated in either SI units or inch-pound units
board, designed for use as a base in multilayer systems or as a
are to be regarded separately as standard. Within the text, the
gypsum stud or core in semisolid or solid gypsum board
SI units are shown in brackets. The values stated in each
partitions, or in shaft wall assemblies.
system may not be exact equivalents; therefore, each system
shall be used independently of the other. Combining values
NOTE 2—The terms backing board, coreboard, and shaftliner board
from the two systems may result in non-conformance with the
refer to different end uses.The term gypsum backing board, as used in this
specification, shall include gypsum coreboard and gypsum shaftliner
standard
board unless otherwise stated.
2. Referenced Documents
1.1.4 Water-resistant gypsum backing board, designed pri-
2
2.1 ASTM Standards:
marily to be used as a base for the application of ceramic or
C11 TerminologyRelatingtoGypsumandRelatedBuilding
plastic tile on walls or ceilings.This product is also suitable for
Materials and Systems
decoration.
C22/C22M Specification for Gypsum
1.1.5 Exterior gypsum soffıt board, designed for use on
C473 Test Methods for Physical Testing of Gypsum Panel
exterior soffits and carport ceilings that are completely pro-
Products
tected from contact with liquid water.
C645 Specification for Nonstructural Steel Framing Mem-
1.1.6 Gypsum sheathing board, designed for use as sheath-
bers
ing on buildings.
C840 Specification for Application and Finishing of Gyp-
1.1.7 Gypsum base for veneer plaster, designed for use as a
sum Board
base for the application of gypsum veneer plaster.
C841 Specification for Installation of Interior Lathing and
1.1.8 Gypsum lath, designed for use as a base for the
Furring
application of gypsum plaster.
C844 Specification for Application of Gypsum Base to
1.1.9 Gypsum ceiling board, designed for use on interior
Receive Gypsum Veneer Plaster
ceilings with framing spaced not more than 24 in. [610 mm] on
C1264 Specification for Sampling, Inspection, Rejection,
center and that affords a surface suitable to receive water-based
Certification, Packaging, Marking, Shipping, Handling,
texture and other decoration. This product is also suitable for
and Storage of Gypsum Panel Products
use on interior walls.
C1280 Specification for Application of Gypsum Sheathing
1
This specification is under the jurisdiction of ASTM Committee C11 on
Gypsum and Related Building Materials and Systems and is the direct responsibility
2
of Subcommittee C11.01 on Specifications and Test Methods for Gypsum Products. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Nov. 15, 2009. Published December 2009. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1998. Last previous edition approved in 2009 as C1396/C1396M – 09. Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/C1396_C1396M-09a. the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C1396/C1396M – 09a
E84 Test Method for Surface Burning Characteristics of wood studs spaced 16 in. [406 mm] on centers with 6d coated
7
Building Materials nails, 1 ⁄8 in. [48 mm]
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1396/C1396M–09 Designation: C1396/C1396M – 09a
Standard Specification for
1
Gypsum Board
This standard is issued under the fixed designation C1396/C1396M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers the gypsum boards described in 1.1.1-1.1.9.
NOTE 1—Specifications C840, C841, C844 and C1280 contain application procedures for gypsum board.
1.1.1 Gypsum wallboard, designed for use on walls, ceilings, or partitions and that affords a surface suitable to receive
decoration.
1.1.2 Predecorated gypsum board, designed for use as the finished surfacing for walls, ceilings, or partitions.
1.1.3 Gypsum backing board, coreboard, and shaftliner board, designed for use as a base in multilayer systems or as a gypsum
stud or core in semisolid or solid gypsum board partitions, or in shaft wall assemblies.
NOTE 2—The terms backing board, coreboard, and shaftliner board refer to different end uses. The term gypsum backing board, as used in this
specification, shall include gypsum coreboard and gypsum shaftliner board unless otherwise stated.
1.1.4 Water-resistant gypsum backing board, designed primarily to be used as a base for the application of ceramic or plastic
tile on walls or ceilings. This product is also suitable for decoration.
1.1.5 Exterior gypsum soffıt board, designed for use on exterior soffits and carport ceilings that are completely protected from
contact with liquid water.
1.1.6 Gypsum sheathing board, designed for use as sheathing on buildings.
1.1.7 Gypsum base for veneer plaster, designed for use as a base for the application of gypsum veneer plaster.
1.1.8 Gypsum lath, designed for use as a base for the application of gypsum plaster.
1.1.9 Gypsum ceiling board, designed for use on interior ceilings with framing spaced not more than 24 in. [610 mm] on center
and that affords a surface suitable to receive water-based texture and other decoration. This product is also suitable for use on
interior walls.
1.2 Specifications applicable to all gypsum boards are located in Section 1-4 and 13-15. Specifications applicable to specific
gypsum boards are located in the following sections:
Section
Gypsum wallboard, predecorated gypsum board 5
Gypsum backing board, gypsum coreboard, 6
gypsum shaftliner board
Water-resistant gypsum backing board 7
Exterior gypsum soffit board 8
Gypsum sheathing board 9
Gypsum base for veneer plaster 10
Gypsum lath 11
Gypsum Ceiling Board 12
1.3 ThevaluesstatedineitherSIunitsorinch-poundunitsaretoberegardedseparatelyasstandard.Withinthetext,theSIunits
are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used
independently of the other. Combining values from the two systems may result in non-conformance with the standard
2. Referenced Documents
2
2.1 ASTM Standards:
C11 Terminology Relating to Gypsum and Related Building Materials and Systems
C22/C22M Specification for Gypsum
1
This specification is under the jurisdiction of ASTM Committee C11 on Gypsum and Related Building Materials and Systems and is the direct responsibility of
Subcommittee C11.01 on Specifications and Test Methods for Gypsum Products.
Current edition approved Sept. 1,Nov. 15, 2009. Published SeptemberDecember 2009. Originally approved in 1998. Last previous edition approved in 20062009 as
C1396/C1396M – 06a9. DOI: 10.1520/C1396_C1396M-09a.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C1396/C1396M – 09a
C473 Test Methods for Physical Testing of Gypsum Panel Products
C645 Specification for Nonstructural Steel Framing Members
C840 Specification for Application and Finishing of Gypsum Board
C841 Specification for Installation of Interior Lathing and Furring
C844 Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster
C1264 Specification for Sampling, Inspection, Rejection, Certifi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.