ASTM C1264-19
(Specification)Standard Specification for Sampling, Inspection, Rejection, Certification, Packaging, Marking, Shipping, Handling, and Storage of Gypsum Panel Products
Standard Specification for Sampling, Inspection, Rejection, Certification, Packaging, Marking, Shipping, Handling, and Storage of Gypsum Panel Products
ABSTRACT
This specification covers sampling; inspection; rejection; certification; packaging and marking; and shipping, handling, and storage of gypsum panel products. When specified by the purchase agreement, samples of gypsum panel products shall be taken at the place of manufacture or at the destination. At least 0.25 % of the number of gypsum panel products in a shipment, but not less than three gypsum panel products, shall be so selected as to be representative of the shipment and shall constitute a sample for the purpose of tests by the purchaser or user. Inspection of the gypsum panel products shall be agreed upon between the purchaser and the producer or supplier as part of the purchase agreement. Rejection of gypsum panel products that fails to conform to the requirements specified shall be reported to the producer or supplier promptly and in writing. When specified in the purchase agreement, a producer's or supplier's report shall be furnished at the time of shipment certifying that the product is in compliance with the ASTM specification. Each gypsum panel product or package shall have legibly marked thereon the following: the thickness, the name of the producer or supplier, the brand name, if any, and the ASTM specification for the product. Gypsum panel products shall be shipped so as to be kept dry. Gypsum panel products shall be stored so as to be kept dry, preferably inside a building. Gypsum panel products shall be neatly stacked flat with care taken to prevent sagging or damage to edges, ends, and surfaces. Where necessary to store gypsum panel products outside, it shall be stacked flat, off the ground, supported on a level platform, and fully protected from weather and direct sunlight exposure.
SCOPE
1.1 This specification covers sampling; inspection; rejection; certification; packaging and marking; and shipping, handling, and storage of gypsum panel products shipped from the manufacturer.
1.1.1 This specification does not cover storage or stocking on individual job sites.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: C1264 − 19
Standard Specification for
Sampling, Inspection, Rejection, Certification, Packaging,
Marking, Shipping, Handling, and Storage of Gypsum Panel
1
Products
This standard is issued under the fixed designation C1264; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 3. Terminology
3.1 Definitions—Definitions shall be in accordance with
1.1 This specification covers sampling; inspection; rejec-
Terminology C11.
tion; certification; packaging and marking; and shipping,
handling, and storage of gypsum panel products shipped from
4. Sampling
the manufacturer.
4.1 When specified by the purchase agreement, samples of
1.1.1 This specification does not cover storage or stocking
gypsum panel products shall be taken at the place of manufac-
on individual job sites.
ture or at the destination. If the samples are taken at the
1.2 This standard does not purport to address all of the
destination, such samples shall be taken within 24 h of the
safety concerns, if any, associated with its use. It is the
receipt of the material.
responsibility of the user of this standard to establish appro-
4.2 Sampling shall comply with 4.2.1 or 4.2.2. Samples
priate safety, health, and environmental practices and deter-
shall be so selected as to be representative of the shipment and
mine the applicability of regulatory limitations prior to use.
shall constitute a sample for the purpose of tests by the
1.3 This international standard was developed in accor-
purchaser or user.
dance with internationally recognized principles on standard-
4.2.1 A sample shall consist of at least 0.25 % of the number
ization established in the Decision on Principles for the
of gypsum panel products in a shipment, but not less than three
Development of International Standards, Guides and Recom-
gypsum panel products.
mendations issued by the World Trade Organization Technical
4.2.2 A sample shall comply with the requirements of a
Barriers to Trade (TBT) Committee.
statistically valid Acceptance Sampling Method based on
accepted National or International Standards. The method
2. Referenced Documents
chosen and confidence level shall be stated.
2
2.1 ASTM Standards:
5. Inspection
C11 Terminology Relating to Gypsum and Related Building
Materials and Systems 5.1 Inspection of the gypsum panel products shall be agreed
upon between the purchaser and the producer or supplier as
C1396/C1396M Specification for Gypsum Board
3 part of the purchase agreement.
2.2 ISO Standards:
ISO 3166–1 Codes for the Representation of Names of
6. Rejection
Countries and Their Subdivisions—Part 1: Country Codes
6.1 Rejection of gypsum panel products that fails to con-
form to the requirements of the specification shall be reported
to the producer or supplier promptly and in writing. The notice
1
This specification is under the jurisdiction of ASTM Committee C11 on
of rejection shall contain a statement documenting how the
Gypsum and Related Building Materials and Systems and is the direct responsibility
gypsum panel products have failed to conform to the require-
of Subcommittee C11.01 on Specifications and Test Methods for Gypsum Products.
Current edition approved Oct. 1, 2019. Published October 2019. Originally
ments of the specification.
approved in 1994. Last previous edition approved in 2014 as C1264 – 14a. DOI:
10.1520/C1264-19.
7. Certification
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
7.1 When specified in the purchase agreement, a producer’s
Standards volume information, refer to the standard’s Document Summary page on
or supplier’s report shall be furnished at the time of shipment
the ASTM website.
3
certifying that the product is in compliance with the ASTM
Available from International Organization for Standardization (ISO), 1, ch. de
la Voie-Creuse, CP 56, CH-1211 Geneva 20, Switzerland, http://www.iso.org. specification referencing this specification.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1264 − 19
8. Packaging and Marking 10. Keywords
8.1 Each gypsum panel product or package shall have 10.1 certification; gypsum; gypsum panel products; han-
legibly marked thereon the following: the thickness, t
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1264 − 14a C1264 − 19
Standard Specification for
Sampling, Inspection, Rejection, Certification, Packaging,
Marking, Shipping, Handling, and Storage of Gypsum Panel
1
Products
This standard is issued under the fixed designation C1264; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers sampling; inspection; rejection; certification; packaging and marking; and shipping, handling, and
storage of gypsum panel products shipped from the manufacturer.
1.1.1 This specification does not cover storage or stocking on individual job sites.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C11 Terminology Relating to Gypsum and Related Building Materials and Systems
C1396/C1396M Specification for Gypsum Board
3
2.2 ISO Standards:
ISO 3166–1 Codes for the Representation of Names of Countries and Their Subdivisions—Part 1: Country Codes
3. Terminology
3.1 Definitions—Definitions shall be in accordance with Terminology C11.
4. Sampling
4.1 When specified by the purchase agreement, samples of gypsum panel products shall be taken at the place of manufacture
or at the destination. If the samples are taken at the destination, such samples shall be taken within 24 h of the receipt of the
material.
4.2 At least 0.25 % of theSampling shall comply with 4.2.1 numberor 4.2.2of gypsum panel products in a shipment, but not less
than three gypsum panel products, shall . Samples shall be so selected as to be representative of the shipment and shall constitute
a sample for the purpose of tests by the purchaser or user.
4.2.1 A sample shall consist of at least 0.25 % of the number of gypsum panel products in a shipment, but not less than three
gypsum panel products.
4.2.2 A sample shall comply with the requirements of a statistically valid Acceptance Sampling Method based on accepted
National or International Standards. The method chosen and confidence level shall be stated.
1
This specification is under the jurisdiction of ASTM Committee C11 on Gypsum and Related Building Materials and Systems and is the direct responsibility of
Subcommittee C11.01 on Specifications and Test Methods for Gypsum Products.
Current edition approved Sept. 1, 2014Oct. 1, 2019. Published October 2014October 2019. Originally approved in 1994. Last previous edition approved in 2014 as
C1264C1264 – 14. – 14a. DOI: 10.1520/C1264-14A.10.1520/C1264-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from International Organization for Standardization (ISO), 1, ch. de la Voie-Creuse, CP 56, CH-1211 Geneva 20, Switzerland, http://www.iso.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1264 − 19
5. Inspection
5.1 Inspection of the gypsum panel products shall be agreed upon between the purchaser and the producer or supplier as part
of the purchase agreement.
6. Rejection
6.1 Rejection of gypsum panel products that fails to conform to the requirements of the specification shall be reported to the
producer or supplier promptly and in writing. The notice of rejection shall contain a statement documenting how the gypsum panel
products have failed to conform to the requirements of the specification.
7. Certification
7.1 When specified in the purchase agreement, a producer’s or supplier’s report shall be furnished at the time of shipment
certifying that the product
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.