ASTM B622-06

Standard Specification for Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube

ABSTRACT
This specification covers seamless pipe and tube of nickel and nickel-cobalt alloys. These alloys are classified into different grades according to chemical composition. Mechanical properties of the material like tensile strength, yield strength, and elongation shall be measured. Tension, hydrostatic, and nondestructive electric tests shall be done on each pipe or tube. The mass or weight of each pipe shall be calculated and the chemical composition of each pipe shall be determined.
SCOPE
1.1 This specification covers seamless pipe and tube of nickel and nickel-cobalt alloys (UNS N10001, UNS N10242, UNS N10665, UNS N12160, UNS N10675, UNS N10276, UNS N06455, UNS N06007, UNS N08320, UNS N06975, UNS N06002, UNS N06985, UNS N06022, UNS N06035, UNS N08135, UNS N06255, UNS N06058, UNS N06059, UNS N06200, UNS N06030, UNS N08031, UNS R30556, UNS N08535, UNS N06250, UNS N06060, UNS N06230, UNS N06686, UNS N10629, UNS N06210, UNS N10624, and UNS R20033)* as shown in .
1.2 Pipe and tube shall be supplied in the solution annealed and descaled condition. When atmosphere control is used, descaling is not necessary.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This specification is limited to tubes up to and including 3.5 in. (88.9 mm) outside diameter.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-May-2006
• ICS: 23.040.15 - Non-ferrous metal pipes
• Technical Committee: B02 - Nonferrous Metals and Alloys
• Drafting Committee: B02.07 - Refined Nickel and Cobalt and Their Alloys

Relations

• Replaces: ASTM B622-04a - Standard Specification for Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube
• Effective Date: 01-Jun-2006
• Replaced By: ASTM B622-10 - Standard Specification for Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube
• Effective Date: 15-Dec-2010
• Referred By: ASTM B924-02(2022) - Standard Specification for Seamless and Welded Nickel Alloy Condenser and Heat Exchanger Tubes With Integral Fins
• Effective Date: 01-Jun-2006
• Referred By: ASTM B366/B366M-23 - Standard Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings
• Effective Date: 01-Jun-2006

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B622 – 06
Standard Specification for
1
Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube
This standard is issued under the fixed designation B622; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope B829 Specification for General Requirements for Nickel
2
and Nickel Alloys Seamless Pipe and Tube
1.1 This specification covers seamless pipe and tube of
E8 Test Methods for Tension Testing of Metallic Materials
nickel and nickel-cobalt alloys (UNS N10001, UNS N10242,
E527 Practice for Numbering Metals and Alloys in the
UNS N10665, UNS N12160, UNS N10675, UNS N10276,
Unified Numbering System (UNS)
UNS N06455, UNS N06007, UNS N08320, UNS N06975,
UNS N06002, UNS N06985, UNS N06022, UNS N06035,
3. Terminology
UNS N08135, UNS N06255, UNS N06058, UNS N06059,
3.1 Definitions:
UNS N06200, UNS N06030, UNS N08031, UNS R30556,
3.1.1 average diameter, n—the average of the maximum
UNS N08535, UNS N06250, UNS N06060, UNS N06230,
and minimum outside diameters, or the maximum and mini-
UNSN06686,UNSN10629,UNSN06210,UNSN10624,and
mum inside diameters, as determined at any cross section of
UNS R20033)* as shown in Table 1.
the tube.
1.2 Pipe and tube shall be supplied in the solution annealed
3.1.2 pipe, n—seamless tube conforming to the particular
and descaled condition. When atmosphere control is used,
dimensions commercially known as standard pipe sizes (Ap-
descaling is not necessary.
pendix X2).
1.3 The values stated in inch-pound units are to be regarded
3.1.3 tube, n—a hollow product of round or any other cross
as the standard. The values given in parentheses are for
section having a continuous periphery.
information only.
1.4 This specification is limited to tubes up to and including
4. General Requirements
3.5 in. (88.9 mm) outside diameter.
4.1 Material furnished under this specification shall con-
1.5 This standard does not purport to address all of the
form to the applicable requirements of Specification B829
safety concerns, if any, associated with its use. It is the
unless otherwise provided herein.
responsibility of the user of this standard to become familiar
with all hazards including those identified in the appropriate
5. Ordering Information
Material Safety Data Sheet (MSDS) for this product/material
5.1 It is the responsibility of the purchaser to specify all
as provided by the manufacturer, to establish appropriate
requirements that are necessary for the material ordered under
safety and health practices, and determine the applicability of
this specification. Examples of such requirements include, but
regulatory limitations prior to use.
are not limited to the following:
5.1.1 Alloy (Table 1).
2. Referenced Documents
5.1.2 Dimensions:
3
2.1 ASTM Standards:
5.1.2.1 Tube—Outside diameter, minimum or average wall
thickness, and length.
5.1.2.2 Pipe—Standard pipe size and schedule (Appendix
1
This specification is under the jurisdiction of ASTM Committee B02 on
X2).
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
5.1.3 Ends—Plain ends cut and deburred will be furnished.
B02.07 on Refined Nickel and Cobalt and Their Alloys.
5.1.4 Certification—State if certification or a report of test
Current edition approved June 1, 2006. Published June 2006. Originally
approved in 1977. Last previous edition approved in 2004 as B622 – 04a. DOI:
results is required (Section 15).
10.1520/B0622-06.
5.1.5 Samples for Check Analysis—State whether samples
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi-
for check analysis should be furnished.
cation SB-622 in Section II of that Code.
5.1.6 Purchaser Inspection—If the purchaser wishes to
* NewdesignationestablishedinaccordancewithPracticeE527andSAEJ1086,
Practice for Numbering Metals and Alloys (UNS).
witness tests or inspection of material at the place of manu-
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
facture, the purchase order must so state, indicating which tests
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
or inspections are to be witnessed (Section 14).
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
B622 – 06
2
TABLE 1 Chemical Requirements
Composition Limits, %
Ni Cr Mo Fe W C Si Co Mn V P S Ti Cu Cb Al Zr La N B Cb Ta Ni+ Mg
max max max (Nb) (Nb) Mo
+Ta
Ni-Mo Alloys
A
N10001 remainder 1.0 26.0- 4.0-6.0 . 0.05 1.0 2.5
...