ASTM B622-04a

Standard Specification for Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube

SCOPE
1.1 This specification covers seamless pipe and tube of nickel and nickel-cobalt alloys (UNS N10001, UNS N10242, UNS N10665, UNS N12160, UNS N10675, UNS N10276, UNS N06455, UNS N06007, UNS N08320, UNS N06975, UNS N06002, UNS N06985, UNS N06022, UNS N06035, UNS N08135, UNS N06255, UNS N06058, UNS N06059, UNS N06200, UNS N06030, UNS N08031, UNS R30556, UNS N08535, UNS N06250, UNS N06060, UNS N06230, UNS N06686, UNS N10629, UNS N06210, UNS N10624, and UNS R20033)* as shown in Table 1.
1.2 Pipe and tube shall be supplied in the solution annealed and descaled condition. When atmosphere control is used, descaling is not necessary.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 30-Sep-2004
• ICS: 23.040.15 - Non-ferrous metal pipes
• Technical Committee: B02 - Nonferrous Metals and Alloys
• Drafting Committee: B02.07 - Refined Nickel and Cobalt and Their Alloys

Relations

• Replaces: ASTM B622-04 - Standard Specification for Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube
• Effective Date: 01-Oct-2004
• Replaced By: ASTM B622-06 - Standard Specification for Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube
• Effective Date: 01-Jun-2006
• Referred By: ASTM B924-02(2022) - Standard Specification for Seamless and Welded Nickel Alloy Condenser and Heat Exchanger Tubes With Integral Fins
• Effective Date: 01-Oct-2004
• Referred By: ASTM B366/B366M-23 - Standard Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings
• Effective Date: 01-Oct-2004

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B 622 – 04a
Standard Specification for
1
Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube
This standard is issued under the fixed designation B 622; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope B 829 Specification for General Requirements for Nickel
2
and Nickel Alloys Seamless Pipe and Tube
1.1 This specification covers seamless pipe and tube of
E 8 Test Methods for Tension Testing of Metallic Materials
nickel and nickel-cobalt alloys (UNS N10001, UNS N10242,
UNS N10665, UNS N12160, UNS N10675, UNS N10276,
3. Terminology
UNS N06455, UNS N06007, UNS N08320, UNS N06975,
3.1 Definitions:
UNS N06002, UNS N06985, UNS N06022, UNS N06035,
3.1.1 average diameter, n—the average of the maximum
UNS N08135, UNS N06255, UNS N06058, UNS N06059,
and minimum outside diameters, or the maximum and mini-
UNS N06200, UNS N06030, UNS N08031, UNS R30556,
mum inside diameters, as determined at any cross section of
UNS N08535, UNS N06250, UNS N06060, UNS N06230,
the tube.
UNSN06686,UNSN10629,UNSN06210,UNSN10624,and
3.1.2 pipe, n—seamless tube conforming to the particular
UNS R20033)* as shown in Table 1.
dimensions commercially known as standard pipe sizes (Ap-
1.2 Pipe and tube shall be supplied in the solution annealed
pendix X2).
and descaled condition. When atmosphere control is used,
3.1.3 tube, n—a hollow product of round or any other cross
descaling is not necessary.
section having a continuous periphery.
1.3 The values stated in inch-pound units are to be regarded
as the standard. The values given in parentheses are for
4. General Requirements
information only.
4.1 Material furnished under this specification shall con-
1.4 This specification is limited to tubes up to and including
form to the applicable requirements of Specification B 829
3.5 in. (88.9 mm) outside diameter.
unless otherwise provided herein.
1.5 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
5. Ordering Information
responsibility of the user of this standard to become familiar
5.1 It is the responsibility of the purchaser to specify all
with all hazards including those identified in the appropriate
requirements that are necessary for the material ordered under
Material Safety Data Sheet for this product/material as pro-
this specification. Examples of such requirements include, but
vided by the manufacturer, to establish appropriate safety and
are not limited to the following:
health practices, and determine the applicability of regulatory
5.1.1 Alloy (Table 1).
limitations prior to use.
5.1.2 Dimensions:
5.1.2.1 Tube—Outside diameter, minimum or average wall
2. Referenced Documents
thickness, and length.
3
2.1 ASTM Standards:
5.1.2.2 Pipe—Standard pipe size and schedule (Appendix
X2).
1
This specification is under the jurisdiction of ASTM Committee B02 on 5.1.3 Ends—Plain ends cut and deburred will be furnished.
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
5.1.4 Certification—State if certification or a report of test
B02.07 on Refined Nickel and Cobalt and Their Alloys.
results is required (Section 15).
Current edition approved Oct. 1, 2004. Published October 2004. Originally
5.1.5 Samples for Check Analysis—State whether samples
approved in 1977. Last previous edition approved in 2004 as B 622 – 04.
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi-
for check analysis should be furnished.
cation SB-622 in Section II of that Code.
5.1.6 Purchaser Inspection—If the purchaser wishes to
* New designation established in accordance withASTM E 527 and SAE J1086,
witness tests or inspection of material at the place of manu-
Practice for Numbering Metals and Alloys (UNS).
3
facture, the purchase order must so state, indicating which tests
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
or inspections are to be witnessed (Section 14).
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
B 622 – 04a
2
TABLE 1 Chemical Requirements
Composition Limits, %
Ni Cr Mo Fe W C Si Co Mn V P S Ti Cu Cb Al Zr La N B Cb Ta Ni+ Mg
max max max (Nb) (Nb) Mo
+Ta
Ni-Mo Alloys
A
N10001 remainder 1.0 26.0- 4.0-6.0 . 0.05 1.0 2.5 1.0 0.2- 0.04 0.03 . . .
max 30.0 max max max 0.4
A
N10665 remainder 1.0 26.0- 2.0 max
...