iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D2439-96(2003)e1

(Specification)

Standard Specification for Refined Phenol

Standard Specification for Refined Phenol

ABSTRACT
This specification covers refined phenol. The refined phenol shall conform to the required water content, solidification point, appearance and molten color when sampled and tested.
SCOPE
1.1 This specification covers refined phenol.
1.2 Consult current OSHA regulations and supplier's Material Safety Data Sheets, and local regulations for all materials listed in this specification.
1.3 The following applies to all specified limits in this specification: for purposes of determining conformance with this specification, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-Feb-2003
ICS
71.080.90 - Phenols
Technical Committee
D16 - Aromatic, Industrial, Specialty and Related Chemicals
Drafting Committee
D16.02 - Oxygenated Aromatics
Current Stage
Ref Project

Relations

Replaces
ASTM D2439-96 - Standard Specification for Refined Phenol
Effective Date
10-Feb-2003
Replaced By
ASTM D2439-96(2008) - Standard Specification for Refined Phenol
Effective Date
01-Dec-2008

Buy Standard

ASTM D2439-96(2003)e1 - Standard Specification for Refined PhenolASTM D2439-96(2003)e1 - Standard Specification for Refined Phenol
PreviousNext
Technical specification
ASTM D2439-96(2003)e1 - Standard Specification for Refined Phenol
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: D 2439 – 96 (Reapproved 2003)
Standard Specification for
Refined Phenol
This standard is issued under the fixed designation D 2439; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
´ NOTE—The words “as is” in the table in Section 3.1 were deleted editorially in February 2003.
1. Scope 2.2 Other Document:
OSHA Regulations,29 CFR, paragraphs 1910.1000 and
1.1 This specification covers refined phenol.
1910.1200
1.2 Consult current OSHAregulations and supplier’s Mate-
rial Safety Data Sheets, and local regulations for all materials
3. Properties
listed in this specification.
3.1 Refined phenol shall conform to the following require-
1.3 The following applies to all specified limits in this
ments when sampled and tested as described:
specification: for purposes of determining conformance with
Specifica- ASTM Test method
this specification, an observed value or a calculated value shall
Property
tion
be rounded off “to the nearest unit” in the last right-hand digit
used in expressing the specification limit, in accordance with Water content, max, weight % 0.10 D 1631
Solidification point, min,° C 40.6 D 1493
the rounding-off method of PracticeE29.
A
Appearance
1.4 This standard does not purport to address all of the B
Molten color
safety concerns, if any, associated with its use. It is the _______________
A
responsibility of the user of this standard to establish appro-
Molten liquid or crystalline solid, free of sediment and haze.
B
Refined phenol as produced is essentially colorless. Depending upon both the
priate safety and health practices and determine the applica-
nature and duration of subsequent handling, it may discolor. Therefore, a rigid
bility of regulatory limitations prior to use.
specification for color is impractical and for many uses it may be unnecessary. In
those cases where such a specification is required, its magnitude will vary widely
2. Referenced Documents
with the intended usage. The required value may be measured using Test Method
D 1686. It is further recommended that the directives of Practice D 3852 be strictly
2.1 ASTM Standards:
followed in any case where color is important.
D 1493 Test Method for Solidification Point of Industrial
Organic Chemicals
4. Sampling
D 1631 Test Method for Water in Phenol and Related
4.1 The material shall be sampled and the properties enu-
Materials by the Iodine Reagent Method
merated in this specification shall be determi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D4789-20e1(Test Method)
Standard Test Method for Solution Color of Bisphenol A (4,4′-Isopropylidenediphenol)

SIGNIFICANCE AND USE
4.1 Color is caused by impurities in the bisphenol A. The acceptable amount of color depends on the end-use of the bisphenol A.  
4.2 This test method can be used for internal quality control. This method provides the information required to set specifications.
SCOPE
1.1 This test method covers the procedure for determination of the Platinum-Cobalt Color of bisphenol A (4,4′-Isopropylidenediphenol) dissolved in methanol.  
1.2 This test method has been found applicable for the determination of solution color of bisphenol A to 20 Pt–Co color units.  
1.3 The following applies for the purposes of determining the conformance of the test results using this test method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 8.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D4493-20(Test Method)
Standard Test Method for Solidification Point of Bisphenol A(4,4′-Isopropylidenediphenol)

SIGNIFICANCE AND USE
5.1 The solidification point of bisphenol A is a direct indication of its purity, although it gives no information as to the nature of any impurities present.  
5.2 High purity bisphenol A has a solidification point of approximately 157°C.  
5.3 This test method can be used for internal quality control or for setting specifications.
SCOPE
1.1 This test method describes the procedure for determination of the solidification point of bisphenol A (4,4′-isopropylidene diphenol).  
1.2 The test method has been found applicable for determination of the solidification point between 150 and 157°C.  
1.3 In determining conformance of the test results using this method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 9.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D2439-20(Specification)
Standard Specification for Refined Phenol

ABSTRACT
This specification covers refined phenol. The refined phenol shall conform to the required water content, solidification point, appearance and molten color when sampled and tested.
SCOPE
1.1 This specification covers refined phenol.  
1.2 The following applies to all specified limits in this specification: for purposes of determining conformance with this specification, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Consult current OSHA regulations and supplier’s Safety Data Sheets, and local regulations for all materials listed in this specification.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4297-15(2020)(Practice)
Standard Practice for Sampling and Handling Bisphenol A(4,4′ -Isopropylidinediphenol)

SIGNIFICANCE AND USE
3.1 This practice is issued to provide information useful in establishing sampling and handling procedures. It is expected that this information will only be utilized in conjunction with an existing health and safety program and consultation with an appropriate SDS. The information provided herein cannot be used as a substitute for expert safety and medical advice as provided in an appropriate SDS, but rather as a supplement to such advice.
SCOPE
1.1 This practice covers procedures for safely sampling and handling 4,4′-isopropylidinediphenol, commercially known as bisphenol A (BPA), in various solid forms, and as a liquid at elevated temperatures in a manner which represents and preserves product quality.  
1.2 Any person sampling or handling this product should have consulted a safety Data Sheet (SDS) for specific first aid instructions and information on the proper equipment to have available for use in the event of personal contact or exposure.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Sections 3, 4, 5, 6, 7 and 8 and an appropriate SDS.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D1631-10(2018)e1(Test Method)
Standard Test Method for Water in Phenol and Related Materials by the Iodine Reagent Method

SIGNIFICANCE AND USE
5.1 This test method is particularly useful for determining small amounts of water in hygroscopic materials. This test method is suitable for setting specifications on materials referenced in the scope. It may also be used as an internal quality control tool and in development or research work.
SCOPE
1.1 This test method covers the determination of water in phenol and related materials such as cresols, xylenols, naphthalene, pyridine, and quinoline.  
1.2 This test method has been found applicable to a variety of materials varying in water content from 100 mg/kg to solutions containing a relatively high percent of water.  
1.3 In determining the conformance of the test results using this method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 9.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D4789-20e1(Test Method)
Standard Test Method for Solution Color of Bisphenol A (4,4′-Isopropylidenediphenol)

SIGNIFICANCE AND USE
4.1 Color is caused by impurities in the bisphenol A. The acceptable amount of color depends on the end-use of the bisphenol A.  
4.2 This test method can be used for internal quality control. This method provides the information required to set specifications.
SCOPE
1.1 This test method covers the procedure for determination of the Platinum-Cobalt Color of bisphenol A (4,4′-Isopropylidenediphenol) dissolved in methanol.  
1.2 This test method has been found applicable for the determination of solution color of bisphenol A to 20 Pt–Co color units.  
1.3 The following applies for the purposes of determining the conformance of the test results using this test method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 8.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D4493-20(Test Method)
Standard Test Method for Solidification Point of Bisphenol A(4,4′-Isopropylidenediphenol)

SIGNIFICANCE AND USE
5.1 The solidification point of bisphenol A is a direct indication of its purity, although it gives no information as to the nature of any impurities present.  
5.2 High purity bisphenol A has a solidification point of approximately 157°C.  
5.3 This test method can be used for internal quality control or for setting specifications.
SCOPE
1.1 This test method describes the procedure for determination of the solidification point of bisphenol A (4,4′-isopropylidene diphenol).  
1.2 The test method has been found applicable for determination of the solidification point between 150 and 157°C.  
1.3 In determining conformance of the test results using this method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 9.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D2439-20(Specification)
Standard Specification for Refined Phenol

ABSTRACT
This specification covers refined phenol. The refined phenol shall conform to the required water content, solidification point, appearance and molten color when sampled and tested.
SCOPE
1.1 This specification covers refined phenol.  
1.2 The following applies to all specified limits in this specification: for purposes of determining conformance with this specification, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Consult current OSHA regulations and supplier’s Safety Data Sheets, and local regulations for all materials listed in this specification.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4297-15(2020)(Practice)
Standard Practice for Sampling and Handling Bisphenol A(4,4′ -Isopropylidinediphenol)

SIGNIFICANCE AND USE
3.1 This practice is issued to provide information useful in establishing sampling and handling procedures. It is expected that this information will only be utilized in conjunction with an existing health and safety program and consultation with an appropriate SDS. The information provided herein cannot be used as a substitute for expert safety and medical advice as provided in an appropriate SDS, but rather as a supplement to such advice.
SCOPE
1.1 This practice covers procedures for safely sampling and handling 4,4′-isopropylidinediphenol, commercially known as bisphenol A (BPA), in various solid forms, and as a liquid at elevated temperatures in a manner which represents and preserves product quality.  
1.2 Any person sampling or handling this product should have consulted a safety Data Sheet (SDS) for specific first aid instructions and information on the proper equipment to have available for use in the event of personal contact or exposure.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Sections 3, 4, 5, 6, 7 and 8 and an appropriate SDS.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D1631-10(2018)e1(Test Method)
Standard Test Method for Water in Phenol and Related Materials by the Iodine Reagent Method

SIGNIFICANCE AND USE
5.1 This test method is particularly useful for determining small amounts of water in hygroscopic materials. This test method is suitable for setting specifications on materials referenced in the scope. It may also be used as an internal quality control tool and in development or research work.
SCOPE
1.1 This test method covers the determination of water in phenol and related materials such as cresols, xylenols, naphthalene, pyridine, and quinoline.  
1.2 This test method has been found applicable to a variety of materials varying in water content from 100 mg/kg to solutions containing a relatively high percent of water.  
1.3 In determining the conformance of the test results using this method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 9.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off