iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F1460-07

(Practice)

Standard Practice for Calibrating Oil Spill Dispersant Application Equipment Boom and Nozzle Systems

Standard Practice for Calibrating Oil Spill Dispersant Application Equipment Boom and Nozzle Systems

SIGNIFICANCE AND USE
This practice will enable calibration of oil spill dispersant application equipment and ensure a desired dosage and uniformity across the swath width.
The data provided by the methods described herein will permit the preparation of a chart relating delivery rate with application vehicle speed, flow meter reading or pump setting so that in actual application, the desired dosage will be achieved.
This practice will ensure that a dispersant application system is functional, capable of delivering a specified dosage, and that major components are operational. This will also ensure that the unit is functioning according to design specifications as detailed in Guide F 1413.
SCOPE
1.1 This practice covers uniform procedures for determining and reporting the dosage rate of oil spill dispersant application equipment.
1.2 This practice is applicable to spray systems employing booms and nozzles and is not fully applicable to other systems such as fire monitors, sonic distributors, or fan-spray guns.
1.3 This practice is applicable to systems for use on ships or boats and helicopters or airplanes.
1.4 This practice is one of four related to dispersant application systems using booms and nozzles. One is on design, one on calibration, one on deposition, and one on the use of the systems. Familiarity with all four standards is recommended.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-Oct-1999
ICS
21.260 - Lubrication systems
Technical Committee
F20 - Hazardous Substances and Oil Spill Response
Drafting Committee
F20.13 - Treatment
Current Stage
Ref Project

Relations

Replaces
ASTM F1460-93(1999) - Standard Practice for Calibrating Oil Spill Dispersant Application Equipment Boom and Nozzle Systems
Effective Date
10-Oct-1999
Replaced By
ASTM F1460-07(2013) - Standard Practice for Calibrating Oil Spill Dispersant Application Equipment Boom and Nozzle Systems
Effective Date
01-Apr-2013
Referred By
ASTM F1413/F1413M-18(2022) - Standard Guide for Oil Spill Dispersant Application Equipment: Boom and Nozzle Systems
Effective Date
10-Oct-1999

Buy Standard

ASTM F1460-07 - Standard Practice for Calibrating Oil Spill Dispersant Application Equipment Boom and Nozzle SystemsASTM F1460-07 - Standard Practice for Calibrating Oil Spill Dispersant Application Equipment Boom and Nozzle Systems
PreviousNext
Standard
ASTM F1460-07 - Standard Practice for Calibrating Oil Spill Dispersant Application Equipment Boom and Nozzle Systems
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F1460 − 07
StandardPractice for
Calibrating Oil Spill Dispersant Application Equipment
1
Boom and Nozzle Systems
This standard is issued under the fixed designation F1460; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope application vehicle speed, flow meter reading or pump setting
so that in actual application, the desired dosage will be
1.1 Thispracticecoversuniformproceduresfordetermining
achieved.
and reporting the dosage rate of oil spill dispersant application
equipment. 3.3 This practice will ensure that a dispersant application
system is functional, capable of delivering a specified dosage,
1.2 This practice is applicable to spray systems employing
and that major components are operational. This will also
booms and nozzles and is not fully applicable to other systems
ensure that the unit is functioning according to design specifi-
such as fire monitors, sonic distributors, or fan-spray guns.
cations as detailed in Guide F1413.
1.3 This practice is applicable to systems for use on ships or
boats and helicopters or airplanes. 4. Apparatus and Materials
1.4 This practice is one of four related to dispersant appli-
4.1 Pails—ofcapacity7to20L(2to5U.S.gal)tocatchthe
cation systems using booms and nozzles. One is on design, one spray from the nozzles.
on calibration, one on deposition, and one on the use of the
4.2 Graduated Cylinder— of capacity 7 to 20 L or a scale
systems. Familiarity with all four standards is recommended.
having capacity of at least 20 kg (45 lbs) to determine the
1.5 This standard does not purport to address all of the
amount of fluid in each pail. Commercial equipment with an
safety concerns, if any, associated with its use. It is the
accuracy of at least 1 % is adequate.
responsibility of the user of this standard to establish appro-
4.3 Stopwatch.
priate safety and health practices and determine the applica-
4.4 Test Fluid—Water can be used as a test fluid if the
bility of regulatory limitations prior to use.
viscosity of the dispersant to be used is not dissimilar to the
viscosity of water. A surrogate fluid should be used if the
2. Referenced Documents
viscosity difference is greater than approximately 100 times
2
2.1 ASTM Standards:
that of water. This can occur with more viscous dispersants or
F1413 Guide for Oil Spill Dispersant Application Equip-
at low temperatures. The surrogate fluid could be water with
ment: Boom and Nozzle Systems
the appropriate amount of thickener.
4.5 Acontinuing supply of water or test fluid, enough to run
3. Significance and Use
the system during the test period, must be available.Tank truck
3.1 This practice will enable calibration of oil spill disper-
quantities may be required.
sant application equipment and ensure a desired dosage and
4.6 Auxiliary Power Units, where required.
uniformity across the swath width.
4.7 Thermometer, to measure the temperature of test fluid.
3.2 The data provided by the methods described herein will
permit the preparation of a chart relating delivery rate with
4.8 Flowmeter—A flowmeter should be incorporated into
the delivery system to measure the total flow out to the booms
and nozzles.
1
This practice is under the jurisdiction of ASTM Committee F20 on Hazardous
5. Calibration Procedure
Substances and Oil Spill Response and is the direct responsibility of Subcommittee
F20.13 on Treatment.
5.1 Synopsis—The calibration procedure is done in four
Current edition approved April 1, 2007. Published April 2007. Originally
steps. The first step is equipment inspection. Any defects are
approved in 1993. Last previous edition approved in 1999 as F1460 – 93 (1999).
DOI: 10.1520/F1460-07.
corrected before further calibration. The second step is the
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
calibration of the flow meter.The third step is calibration of the
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
unit by catching water spray from each nozzle. The fourth step
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. is the preparation of a calibration curve.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1460 − 07
5.2 Equipment Setup— Place the application equipment at a nozzles.Total flow is the sum of the fluid collected from all the
suitable outdoor location and close to a supply of water or test nozzles. The output of each nozzle should be within 10 % of
fluid. Set up the equipment in
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F1460/F1460M-18(2022)(Practice)
Standard Practice for Calibrating Oil Spill Dispersant Application Equipment Boom and Nozzle Systems

SIGNIFICANCE AND USE
3.1 This practice will enable calibration of oil spill dispersant application equipment and ensure a desired dosage and uniformity across the swath width.  
3.2 The data provided by the methods described herein will permit the preparation of a chart relating delivery rate with application vehicle speed, flow meter reading or pump setting so that in actual application, the desired dosage will be achieved.  
3.3 This practice will ensure that a dispersant application system is functional, capable of delivering a specified dosage, and that major components are operational. This will also ensure that the unit is functioning according to design specifications as detailed in Guide F1413.
SCOPE
1.1 This practice covers uniform procedures for determining and reporting the dosage rate of oil spill dispersant application equipment.  
1.2 This practice is applicable to spray systems employing booms and nozzles and is not fully applicable to other systems such as fire monitors, sonic distributors, or fan-spray guns.  
1.3 This practice is applicable to systems for use on ships, boats, helicopters, or airplanes.  
1.4 This practice is one of four related to dispersant application systems using booms and nozzles. One is on design, one on calibration, one on deposition, and one on the use of the systems. Familiarity with all four standards is recommended.  
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1413/F1413M-18(2022)(Guide)
Standard Guide for Oil Spill Dispersant Application Equipment: Boom and Nozzle Systems

ABSTRACT
This guide covers design criteria, requirements, material characteristics, and essential features for oil spill dispersant application systems, it covers spray systems employing booms and nozzles for use on boats or ships and helicopters or airplane. The equipment description, equipment minimum performance specification, and equipment design are presented in details. Materials on ship or boat systems should be corrosion-resistant to salt water. All materials that come into contact with dispersants should be compatible with that dispersant.
SCOPE
1.1 This guide covers design criteria, requirements, material characteristics, and essential features for oil spill dispersant application systems. This guide is not intended to be restrictive to a specific configuration.  
1.2 This guide covers spray systems employing booms and nozzles and is not fully applicable to other systems such as fire monitors, sonic distributors, or fan-spray guns.  
1.3 This guide covers systems for use on ships, boats, helicopters, or airplanes.  
1.4 This guide is one of several related to dispersant application systems using booms and nozzles. One is on design, one on calibration, one on deposition measurements, and one on the use of the systems. Familiarity with all four guides is recommended.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM D7217-22(Test Method)
Standard Test Method for Determining Extreme Pressure Properties of Solid Bonded Films Using a High-Frequency, Linear-Oscillation (SRV) Test Machine

SIGNIFICANCE AND USE
5.1 This laboratory test method can be used to quickly determine extreme pressure properties of parts coated with solid bonded films at selected temperatures specified for use in unlubricated applications where high-speed vibrational or start-stop motions are present with high Hertzian point contact. This test method has found wide application in qualifying solid bonded films used in automotive door lock mechanisms, hinge joints, bolts, and in aerospace. This test method is a material and application oriented approach for characterizing the tribological behaviour using random, discrete and constant parameter combinations. Users of this test method should determine whether results correlate with field performance or other applications.
SCOPE
1.1 This test method covers a procedure for determining extreme pressure properties of solid bonded films under high-frequency linear-oscillation motion using the SRV test machine.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM F1460/F1460M-18(2022)(Practice)
Standard Practice for Calibrating Oil Spill Dispersant Application Equipment Boom and Nozzle Systems

SIGNIFICANCE AND USE
3.1 This practice will enable calibration of oil spill dispersant application equipment and ensure a desired dosage and uniformity across the swath width.  
3.2 The data provided by the methods described herein will permit the preparation of a chart relating delivery rate with application vehicle speed, flow meter reading or pump setting so that in actual application, the desired dosage will be achieved.  
3.3 This practice will ensure that a dispersant application system is functional, capable of delivering a specified dosage, and that major components are operational. This will also ensure that the unit is functioning according to design specifications as detailed in Guide F1413.
SCOPE
1.1 This practice covers uniform procedures for determining and reporting the dosage rate of oil spill dispersant application equipment.  
1.2 This practice is applicable to spray systems employing booms and nozzles and is not fully applicable to other systems such as fire monitors, sonic distributors, or fan-spray guns.  
1.3 This practice is applicable to systems for use on ships, boats, helicopters, or airplanes.  
1.4 This practice is one of four related to dispersant application systems using booms and nozzles. One is on design, one on calibration, one on deposition, and one on the use of the systems. Familiarity with all four standards is recommended.  
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1413/F1413M-18(2022)(Guide)
Standard Guide for Oil Spill Dispersant Application Equipment: Boom and Nozzle Systems

ABSTRACT
This guide covers design criteria, requirements, material characteristics, and essential features for oil spill dispersant application systems, it covers spray systems employing booms and nozzles for use on boats or ships and helicopters or airplane. The equipment description, equipment minimum performance specification, and equipment design are presented in details. Materials on ship or boat systems should be corrosion-resistant to salt water. All materials that come into contact with dispersants should be compatible with that dispersant.
SCOPE
1.1 This guide covers design criteria, requirements, material characteristics, and essential features for oil spill dispersant application systems. This guide is not intended to be restrictive to a specific configuration.  
1.2 This guide covers spray systems employing booms and nozzles and is not fully applicable to other systems such as fire monitors, sonic distributors, or fan-spray guns.  
1.3 This guide covers systems for use on ships, boats, helicopters, or airplanes.  
1.4 This guide is one of several related to dispersant application systems using booms and nozzles. One is on design, one on calibration, one on deposition measurements, and one on the use of the systems. Familiarity with all four guides is recommended.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM G204-21(Test Method)
Standard Test Method for Damage to Contacting Solid Surfaces under Fretting Conditions

SIGNIFICANCE AND USE
5.1 Fretting wear and corrosion are potential serviceability factors in many machines. They have always been factors in shipping finished goods by truck or rail. Packing materials rubbing on a product in transit can make the product unsalable. Beverage cans and food cans can lose their trade dress and consumers often equate container damage to content damage.  
5.2 Clamping surfaces on injection molds are damaged by fretting motions on clamping. This damage is a significant cause for mold replacement.  
5.3 Machines in shipment are subject to fretting damage in the real area of contact of the bearings on the machines.  
5.4 Operating vibration and movement of mechanically clamped components, like screwed assemblies, can produce damage on the clamped faces and other faces that affects machine function or use. Many times fretting damage appears in the form of pits, which are stress concentrators that can lead to mechanical fractures.  
5.5 Electrical contacts in any device that is subject to vibration are susceptible to failure (open circuit) due to fretting damage at real areas of contact.  
5.6 This test method is intended to be used to identify mating couples that may be less prone to fretting damage than others. This information in turn is used to select materials of construction or surface treatments that are less prone to fretting damage for applications where fretting conditions are known or perceived to exist.  
5.7 When using this test method to screen candidate material pairs for a specific application, the user should ensure that the prescribed geometry and test conditions described in Sections 6 – 8 adequately simulate the intended end use. The rationale for any deviations from the prescribed test conditions, if any, shall be explained in the test report and, accordingly, the user shall report that they used a modified version of the standard.
SCOPE
1.1 This test method may be used for either fundamental or applications-oriented studies of fretting damage. Accordingly, data from these tests may be used to rank the wear resistance of candidate material couples for certain types of machine components whose service life is limited by fretting.  
1.2 This test method uses a tribological bench test apparatus with a mechanism or device that will produce the necessary relative motion between a contacting hemispherical rider and a flat counterface. The rider is pressed against the flat counterface with a loading mass. The test method is intended for use in room temperature air. Other configurations or test parameters may be needed to investigate fretting in the presence of lubricants or other environments.  
1.3 The purpose of this test method is to rub two solid surfaces together under controlled fretting conditions and to quantify the damage to both surfaces in units of volume loss.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D8227-20(Test Method)
Standard Test Method for Determining the Coefficient of Friction of Synchronizer Lubricated by Mechanical Transmission Fluids (MTF) Using a High-Frequency, Linear-Oscillation (SRV) Test Machine

SIGNIFICANCE AND USE
5.1 This test method can be used to quickly determine the lubricating ability of fully-formulated lubricants used as mechanical transmission fluids (MTF) to display a frictional behavior against materials used in synchronizers of mechanical gears in automotive vehicles. This test method has found to be complementary to bench tests (for example, Test Method D5579 and CEC L-66-99) by using the present test conditions. This test method is a material and application oriented approach based on inputs from field experiences for characterizing the frictional behavior (coefficient of friction (cof)) using random, discrete, and constant parameter combinations as seen in field experiences. Users of this test method should determine whether results correlate with field performance or other applications prior to commercialization.
SCOPE
1.1 This test method covers a procedure for determining the coefficient of friction of lubricants (fluids) tribologically interacting with materials used in synchronizers in mechanical transmission (MT) gears under high-frequency linear-oscillation motion using the SRV test machine. A flat areal contact geometry is applied.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM G203-10(2020)(Guide)
Standard Guide for Determining Friction Energy Dissipation in Reciprocating Tribosystems

SIGNIFICANCE AND USE
5.1 Many sliding systems exhibit intermittent high friction force excursions compared to competing tribosystems. However, where friction forces or friction coefficients are averaged, the test data may show that the two systems have the same friction characteristics, when in fact they were not the same; there was a friction “problem” in the one with the periodic aberrations. The FED takes into account all friction forces that occur in the test increment. It is all of the friction energy that the couple dissipated in the designated test duration. It captures the friction profile of a system in a single number that can be used to screen candidate couples for friction characteristics.  
5.2 If the friction energy used in a reciprocating tribosystem is of concern this metric along with the friction recording, average coefficient of friction, and standard deviation of the force readings, produces the most meaningful data. It is a metric of the energy loss in a tribosystem.
SCOPE
1.1 This guide covers and is intended for use in interpreting the friction forces recorded in reciprocating tribosystems. The guide applies to any reciprocating tribosystem, whether it is a wear or fretting test or an actual machine or device.  
1.2 The energy dissipation guide was developed in analyzing friction results in the Test Method G133 reciprocating ball-on-flat test, but it applies to other ASTM or ISO reciprocating tests. This technique is frequently used to record the friction response in fretting tribosystems.  
1.3 Specimen material may play some role in the results if the materials under test display viscoelastic behavior. This guide as written is for metals, plastics, and ceramics that do not display viscoelastic behavior. It also applies to lubricated and non-lubricated contacts.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    8 pages
    English language
    sale 15% off
ASTM
ASTM E2336-20(Test Method)
Standard Test Methods for Fire Resistive Grease Duct Enclosure Systems

SIGNIFICANCE AND USE
5.1 These test methods are intended to evaluate the ability of the grease duct enclosure system to do the following:  
5.1.1 Resist the effects of a standardized fire exposure,  
5.1.2 Retain its integrity, or  
5.1.3 Exhibit both properties dependent upon the type of test assembly involved during a predetermined test exposure.  
5.2 These test methods provide for the following measurements and evaluations where applicable:  
5.2.1 Capability of the enclosure material to resist flaming (combustion) when exposed to 1382°F (750°C).  
5.2.2 Loadbearing ability of the tested support system and fastening system to carry the load of the grease duct enclosure system during a standardized fire-engulfment test.  
5.2.3 Ability of a fire stop to meet the requirements of Test Method E814 when used with a grease duct enclosure system.  
5.2.4 Ability of the enclosure material to resist the passage of flames and hot gases during a standardized fire resistance test and a standardized internal fire test.  
5.2.5 Transmission of heat through the grease duct and the enclosure material(s) during a standardized fire resistance test and a standardized internal fire test.  
5.2.6 Ability of the grease duct enclosure system to resist the passage of water during a standardized hose stream test.  
5.2.7 Comparative measurement of temperature aging of the enclosure material(s) when subjected to standardized cyclic thermal transmissions.  
5.3 These test methods do not provide the following:  
5.3.1 Full information as to performance of the enclosure material or the grease duct enclosure system constructed with components, densities, or dimensions other than those tested.  
5.3.2 Evaluation of the degree by which the enclosure material or grease duct enclosure system contributes to the fire hazard by generation of smoke, toxic gases, or other products of combustion.  
5.3.3 Measurement of the degree of control or limitation of the passage of smoke or products of combustion ...
SCOPE
Note 1: The majority of this standard is based on the Model Building Code Evaluation Service2 Acceptance Criteria titled  ACCEPTANCE CRITERIA FOR GREASE DUCT ENCLOSURE ASSEMBLIES, AC101, which was created in 1994. Numerous design listings and labeled materials exist based on the provisions of this standard.  
1.1 These test methods evaluate the enclosure materials and the grease duct enclosure systems using the following test methods: noncombustibility, fire resistance, durability, internal fire, and fire-engulfment with a through-penetration fire stop.  
1.2 These test methods prescribe a standardized fire exposure for comparing the test results of the enclosure materials and grease duct enclosure systems. The results of these tests are one factor in assessing predicted fire performance of grease duct enclosure systems. Using these test results to predict the performance of actual grease duct enclosure systems requires the evaluation of test conditions.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The text of these test methods references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the fire test response standard.  
1.5 These test methods are used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.  
1.6 These test methods do not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of these test methods to establish appr...

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    English language
    sale 15% off
ASTM
ASTM F1567-94(2019)(Specification)
Standard Specification for Fabricated or Cast Automatic Self-Cleaning, Fuel Oil and Lubricating Oil Strainers

ABSTRACT
This specification covers the material, operating, and testing requirements for automatic or continuously self-cleaning strainers, or both, for use in fuel oil and lubricating oil systems and in any marine environment. The strainer may be either hydraulic, electric, or pneumatic operated, and is designed to operate under positive pressure, that is, on the discharge side of the pump. The strainers should operate at specified pressures, temperatures, shipboard environments, and self-cleaning rates. They shall also undergo flow capacity test, inclined flow capacity test, strength of internals test, and self-cleaning and filtration efficiency test.
SCOPE
1.1 This specification covers automatic or continuously self-cleaning automatic strainers, or both, for use in fuel and lubrication oil systems. The strainer is designed to operate under positive pressure (discharge side of the pump). Strainers manufactured to this specification are suitable for use in any marine environment.  
1.2 It is not the intent of this document to redefine existing filtration standards. The intent is to provide sound guidelines for purchasers and designers of lube oil and fuel oil systems. Nominal micron requirements and filter efficiencies shall be as agreed upon by the purchaser and manufacturer and stated in the purchase order document.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off