ASTM A705/A705M-22

Standard Specification for Age-Hardening Stainless Steel Forgings

ABSTRACT
This specification covers age-hardening stainless steel forgings for general use. Materials for forgings shall consist of billets or bars and shall either be forged, rolled, or cast or a section cut from an ingot. The steel specimens shall be solution annealed and age hardened and shall conform to the required values of tensile strength, yield strength, elongation, reduction of area, hardness and impact Charpy-V. The steel materials shall conform to the required chemical compositions of carbon, manganese, phosphorus, sulfur, silicon, chromium, nickel, aluminum, molybdenum, titanium, copper, nitrogen, columbium, and tantalum.
SCOPE
1.1 This specification2 covers age-hardening stainless steel forgings for general use.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units.  
Note 1: Bar products are covered by Specification A564/A564M.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 31-Mar-2022
• ICS: 77.140.85 - Iron and steel forgings
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.17 - Flat-Rolled and Wrought Stainless Steel

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A705/A705M − 22
Standard Specification for
1
Age-Hardening Stainless Steel Forgings
This standard is issued under the fixed designation A705/A705M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* E527 Practice for Numbering Metals and Alloys in the
2 Unified Numbering System (UNS)
1.1 This specification covers age-hardening stainless steel
4
2.2 Other Document:
forgings for general use.
SAE J 1086 Recommended Practice for Numbering Metals
1.2 The values stated in either SI units or inch-pound units
and Alloys (UNS)
are to be regarded separately as standard. The values stated in
each system are not necessarily exact equivalents; therefore, to
3. Ordering Information
ensure conformance with the standard, each system shall be
3.1 It is the responsibility of the purchaser to specify all
used independently of the other, and values from the two
requirements that are necessary for material ordered under this
systems shall not be combined.
specification. Such requirements may include but are not
1.3 Unless the order specifies an “M” designation, the
limited to the following:
material shall be furnished to inch-pound units.
3.1.1 Quantity (weight or number of pieces),
3.1.2 Name of material (age-hardening stainless steel
NOTE 1—Bar products are covered by Specification A564/A564M.
forgings),
1.4 This international standard was developed in accor-
3.1.3 Dimensions, including prints or sketches,
dance with internationally recognized principles on standard-
3.1.4 Type or UNS designation (Table 1),
ization established in the Decision on Principles for the
3.1.5 Heat-treated condition (Section 5),
Development of International Standards, Guides and Recom-
3.1.6 Transverse properties when required (7.4),
mendations issued by the World Trade Organization Technical
3.1.7 ASTM designation and date of issue, and
Barriers to Trade (TBT) Committee.
3.1.8 Special requirements (5.3 and 5.4).
2. Referenced Documents
3.2 If possible, the intended end use of the item should be
3
given on the purchase order, especially when the item is
2.1 ASTM Standards:
ordered for a specific end use or uses.
A370 Test Methods and Definitions for Mechanical Testing
of Steel Products
NOTE 2—A typical ordering description is as follows: five age-
A484/A484M Specification for General Requirements for hardening stainless steel forgings, Type 630, solution-annealed, Specifi-
cation A705 dated __ . End use: pump blocks for oil well equipment.
Stainless Steel Bars, Billets, and Forgings
A564/A564M Specification for Hot-Rolled and Cold-
4. General Requirements
Finished Age-Hardening Stainless Steel Bars and Shapes
4.1 In addition to the requirements of this specification, all
A751 Test Methods and Practices for Chemical Analysis of
requirements of the current edition of Specification A484/
Steel Products
A484M shall apply. Forgings shall comply with the Terminol-
A788/A788M Specification for Steel Forgings, General Re-
ogy and Forging sections of Specification A788/A788M,
quirements
which further clarify the forging definitions in the Terminology
section of Specification A484/A484M. Failure to comply with
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, the general requirements of Specification A484/A484M, con-
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
stitutes nonconformance with this specification.
A01.17 on Flat-Rolled and Wrought Stainless Steel.
Current edition approved April 1, 2022. Published April 2022. Originally
5. Materials and Manufacture
ɛ1
approved in 1974. Last previous edition approved in 2020 as A705/A705M – 20 .
DOI: 10.1520/A0705_A0705M-22.
5.1 Material for forgings shall consist of billets or bars,
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi-
either forged, rolled, or cast, or a section cut from an ingot. The
cation SA-705/SA-705M in Section II of that Code.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
4
Standards volume information, refer to the standard’s Document Summary page on Available from SAE International (SAE), 400 Commonwealth Dr., Warrendale,
the ASTM website. PA 15096, http://www.sae.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
A705/A705M − 22
A
TABLE 1 Chemical Requirements
Composition, %
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: A705/A705M − 20 A705/A705M − 22
Standard Specification for
1
Age-Hardening Stainless Steel Forgings
This standard is issued under the fixed designation A705/A705M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—The minimum allowable yield strength of Type 630, Condition H1150D found in Table 3 was corrected editori-
ally in May 2021.
1. Scope*
2
1.1 This specification covers age-hardening stainless steel forgings for general use.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used
independently of the other, and values from the two systems shall not be combined.
1.3 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units.
NOTE 1—Bar products are covered by Specification A564/A564M.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A484/A484M Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings
A564/A564M Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes
A751 Test Methods and Practices for Chemical Analysis of Steel Products
A788/A788M Specification for Steel Forgings, General Requirements
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
4
2.2 Other Document:
SAE J 1086 Recommended Practice for Numbering Metals and Alloys (UNS)
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.17
on Flat-Rolled and Wrought Stainless Steel.
Current edition approved March 1, 2020April 1, 2022. Published March 2020April 2022. Originally approved in 1974. Last previous edition approved in 20172020 as
ɛ1
A705/A705M – 17.A705/A705M – 20 . DOI: 10.1520/A0705_A0705M-20E01.10.1520/A0705_A0705M-22.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SA-705/SA-705M in Section II of that Code.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from SAE International (SAE), 400 Commonwealth Dr., Warrendale, PA 15096, http://www.sae.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
A705/A705M − 22
A
TABLE 1 Chemical Requirements
Composition, %
UNS Other
Type C Mn P S Si Cr Ni Al Mo Ti Cu
B C
Designation Elements
D
S17400 630 0.07 1.00 0.040 0.030 1.00 15.00–17.50 3.00–5.00 . . . 3.00–5.00
S17700 631 0.09 1.00 0.040 0.030 1.00 16.00–18.00 6.50–7.75 0.75–1.50 . . . .
S15700 632 0.09 1.00 0.040 0.030 1.00 14.00–16.00 6.50–7.75 0.75–1.50 2.00–3.00 . . .
E
S35500 634 0.10–0.15 0.50–1.25 0.040 0.030 0.50 15.00–16.00 4.00–5.00 . 2.50–3.25 . .
S17600 635 0.08 1.00 0.040 0.030 1.00 16.00–17.50 6.00–7.50 0.40 . 0.40–1.20 . .
D
S15500 XM-12 0.07 1.00 0.040 0.030 1.00 14.00–15.50 3.50–5.50 . . . 2.50–4.50
F
S13800 XM-13 0.05 0.20 0.010 0.008 0.10 12.25–13.25 7.50–8.50 0.90–1.35 2.00–2.50 . .
G
S45500 XM-16 0.03 0.50 0.015 0.015 0.50 11.00–12.50 7.50–9.50 . 0.50 0.90–1.40 1.50–2.50
G
S45503 . 0.010 0.50 0.010 0.010 0.20 11.00–12.50 7.50–9.50 . 0.50 1.00–1.35 1.50–2.50
H
S45000 XM-25 0.05 1.00 0.030 0.030 1.00 14.00–16.00 5.00–7.00 . 0.50–1.00 . 1.25–1.75
F
S10120 0.02 0.25 0.015 0.010 0.25 11.00–12.50 9.00–10.50 0.80–1.10 1.75–2.25 0.20–0.50 .
F
S11100 0.02 0.25 0.015 0.010 0.25 11.00–12.50 10.25–11.25 1.35–1.75 1.75–2.25 0.
...