This document applies to bright steel products in the drawn, turned or ground condition delivered in straight lengths. This document is mainly applied to stainless steels of EN 10088-3 and other product standards, e.g. tool steels, roller bearing steels. This document can also be used for cold heading steels both in the form of bars and wire.
The non-alloy and alloy steels of EN 10277 are no longer included.
This document does not cover cold rolled products and cut lengths produced from strip or sheet by cutting.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document applies to bright steel products in the drawn, turned or ground condition delivered in straight lengths. This document is mainly applied to stainless steels of EN 10088-3 and other product standards, e.g. tool steels, roller bearing steels.
This document can also be used for cold heading steels in the form of bars and wire; in case of wire, the thickness and tolerances apply but not the length and the straightness.
The non-alloy and alloy steels of EN 10277 are no longer included.
This document does not cover cold rolled products and cut lengths produced from strip or sheet by cutting.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the requirements relating to:
Steel X5CrNiCu15-5 (1.4545)
Consumable electrode remelted (ESR or VAR)
Solution treated and precipitation treated (H1025)
Bars for machining
a or D ≤ 250 mm
1 070 MPa ≤ Rm ≤ 1 200 MPa
Premium quality (pq)
for aerospace applications.
NOTE   Other designation: The ASD-STAN designation of this material is FE-PM1802.
Only the chemical composition of this document are to be considered.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the requirements relating to:
Steel X4CrNiMo16-5-1 (1.4418)
Air melted
Hardened and tempered
Bars
De ≤ 200 mm
1 150 MPa ≤ Rm ≤ 1 300 MPa
for aerospace applications.
NOTE   Other common designations:
-   AIR: Z 8 CND 17-04.
-   Only the chemical composition according to this document is considered.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the requirements relating to:
Heat-resisting alloy NI-PH1301 (NiCr19Co18Mo4Ti3Al3)
Solution treated and precipitation treated
Bars and sections
De ≤ 200 mm
for aerospace applications.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the requirements relating to:
Steel X3CrNiMoAl (13-8-2)
Vacuum induction melted and consumable electrode remelted
Solution treated and precipitation treated
Bars for machining
a or D ≤ 200 mm
1 200 MPa ≤ Rm ≤ 1 350 MPa
for aerospace applications.
Material no (W.L): 1.4534.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document defines the requirements for the ordering, manufacture, testing, inspection and delivery of steel and heat resisting alloy bars and sections. It shall be applied when referred to and in conjunction with the EN material standard unless otherwise specified on the drawing, order or inspection schedule.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the requirements relating to:
Steel X12CrNiMoV12-3 (1.4938)
Air melted and consumable electrode remelted
Hardened and tempered
Bars
De ≤ 150 mm
900 MPa ≤ Rm ≤ 1 100 MPa
for aerospace applications.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the requirements relating to: Steel X5CrNoMoCuNb14-5 (1.4594) 930 MPa ≤ Rm ≤ 1 080 MPa Bars De ≤ 150 mm.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the nominal dimensions and the tolerances on dimensions and shape of hot-rolled steel flat bars and steel wide flats for general purposes.
This document is not applicable to spring leaves, see EN 10092-1.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies technical delivery requirements for the surface quality of round bars, squares, hexagons and wire rod in the hot rolled condition with nominal dimensions dN from 5 mm to 200 mm. This document is applicable to bright products and tool steels, if agreed at the time of enquiry and order between manufacturer and purchaser.
By agreement between manufacturer and purchaser, this document can also be applied to other special profiles.
This document is particularly applicable to steels for engineering and structural applications.
This document does not include any requirements for the permissible depth of surface decarburization.
NOTE       The determination of depth of surface decarburization is presented in ISO 3887.
The material standards for steel bars and wire rod can exclude the application of one or other of the surface quality classes of this document. They can also cover requirements for surface quality which deviate from this document. In these cases the requirements of the material standard prevail.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the technical delivery requirements for bright steel bars in the drawn, peeled/turned or ground condition and they are intended for mechanical purposes, for example for machine parts. The bright bars are subdivided into the following steel types:
a)   non-alloy general engineering steels;
b)   non-alloy free-cutting steels;
c)   non-alloy and alloy case-hardening steels;
d)   non-alloy and alloy steels for quenching and tempering.
This document lists the mechanical characteristics for products up to 100 mm in thickness. For larger dimensions, the manufacturer and purchaser agree on mechanical properties at the time of enquiry and order.
It does not cover cold rolled products and cut lengths produced from strip or sheet by cutting. Bright steel products of stainless steels are to be found in EN 10088 3.
In addition to this document, the general technical delivery requirements of EN 10021 are applicable.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the nominal dimensions and the tolerances on dimensions and shape of hot-rolled steel flat bars and steel wide flats for general purposes.
This standard is not applicable to spring leaves, see EN 10092-1.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This International Standard specifies technical delivery requirements for the surface quality of round bars, squares, hexagons and wire rod in the hot rolled condition with nominal diameters dN from 5 mm to 200 mm. By agreement between manufacturer and purchaser, this International Standard may also be applied to other special profiles. This International Standard applies particularly to steels for engineering and structural applications and, by agreement, may also be applied to tool steels.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This European Standard is applicable to round rod, round bars and wire made of stainless steels intended for cold heading and cold extrusion having a diameter up to and including:
-   25 mm for ferritic and austenitic-ferritic steels;
-   50 mm for austenitic steels;
-   100 mm for martensitic steels.
1.2   EN 10263 1 is indispensable for the application of this part of EN 10263.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 is applicable to round rod and round bars and wire with a diameter up to and including 100 mm, of non-alloy and alloy steel, intended for cold heading, cold extrusion, subsequent quenching and tempering and induction hardening or flame hardening.
1.2   prEN 10263-1:2013 is indispensable for this Part of EN 10263.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 is applicable to round rod, round bars and wire with a diameter up to and including 100 mm, of non-alloy and alloy steel, intended for cold heading and cold extrusion and subsequent case hardening treatment.
1.2   prEN 10263-1:2013 is indispensable for this Part of EN 10263.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 is applicable to round rod and bars and wire with a diameter up to and including 100 mm, of non-alloy and alloy steel, intended for cold heading and cold extrusion without subsequent heat treatment on the final components.
1.2   prEN 10263-1:2013 is indispensable for this Part of EN 10263.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 specifies the general technical delivery conditions for round rod, round bars and wire for cold heading and cold extrusion made of:
a)   non alloy steels not intended for heat treatment after cold working, as specified in prEN 10263-2:2013;
b)   non alloy and alloy steels for case hardening, as specified in prEN 10263-3:2013;
c)   non alloy and alloy steels for quenching and tempering, as specified in prEN 10263-4:2013;
d)   stainless steels, as specified in prEN 10263-5:2013.
1.2   Parts 2,3 and 4 of this EN 10263 cover products having a diameter up to and including 100 mm.
Part 5 covers products having a diameter up to and including:
-   25 mm for ferritic and austenitic-ferritic steels;
-   50 mm for austenitic steels;
-   100 mm for martensitic steels.
1.3   In special cases supplementary requirements or deviations with respect to this European Standard may be agreed between the purchaser and the supplier at the time of enquiry and order (See Annex A).
1.4   The general technical delivery conditions in EN 10021 also apply to products supplied in accordance with this European Standard

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies technical delivery requirements for the surface quality of round bars, squares, hexagons and wire rod in the hot rolled condition with nominal dimensions dN from 5 mm to 200 mm. This document is applicable to bright products and tool steels, if agreed at the time of enquiry and order between manufacturer and purchaser. By agreement between manufacturer and purchaser, this document can also be applied to other special profiles. This document is particularly applicable to steels for engineering and structural applications. This document does not include any requirements for the permissible depth of surface decarburization. NOTE The determination of depth of surface decarburization is presented in ISO 3887. The material standards for steel bars and wire rod can exclude the application of one or other of the surface quality classes of this document. They can also cover requirements for surface quality which deviate from this document. In these cases the requirements of the material standard prevail.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    8 pages
    French language
    sale 15% off
  • Standard
    8 pages
    French language
    sale 15% off

ISO 16120-4:2017 specifies requirements for wire rod for conversion to wire for special applications. It is applicable to non-alloy steel wire rod with improved characteristics intended for drawing and/or cold rolling.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    German language
    sale 10% off
    e-Library read for
    1 day

ISO 16120-1:2017 series is applicable to wire rod of non-alloy steel intended for wire drawing and/or cold rolling. The cross-section can be circular, oval, square, rectangular, hexagonal, octagonal, half-round or another shape, generally with at least 5 mm nominal dimension, and with a smooth surface.
ISO 16120-1:2017 specifies general requirements for non-alloy steel wire rod for conversion to wire. It is not applicable to products for which standards exist or are in development, for example:
-      steel wire rod intended for heat treatment;
-      free-cutting steel wire rod;
-      steel wire rod for cold heading and cold extrusion;
-      steel wire rod intended for the production of electrodes and products for welding;
-      steel wire rod for welded fabric for reinforcement for concrete;
-      steel wire rod for ball and roller bearings (see ISO 683‑17);
-      steel wire rod for wire for high fatigue strength mechanical springs, such as valve springs.
In addition to the requirements of this document, the general technical delivery requirements specified in ISO 404 apply.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    German language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 specifies the general technical delivery conditions for round rod, round bars and wire for cold heading and cold extrusion made of:
a)   non alloy steels not intended for heat treatment after cold working, as specified in prEN 10263-2:2013;
b)   non alloy and alloy steels for case hardening, as specified in prEN 10263-3:2013;
c)   non alloy and alloy steels for quenching and tempering, as specified in prEN 10263-4:2013;
d)   stainless steels, as specified in prEN 10263-5:2013.
1.2   Parts 2,3 and 4 of this EN 10263 cover products having a diameter up to and including 100 mm.
Part 5 covers products having a diameter up to and including:
-   25 mm for ferritic and austenitic-ferritic steels;
-   50 mm for austenitic steels;
-   100 mm for martensitic steels.
1.3   In special cases supplementary requirements or deviations with respect to this European Standard may be agreed between the purchaser and the supplier at the time of enquiry and order (See Annex A).
1.4   The general technical delivery conditions in EN 10021 also apply to products supplied in accordance with this European Standard

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 is applicable to round rod and bars and wire with a diameter up to and including 100 mm, of non-alloy and alloy steel, intended for cold heading and cold extrusion without subsequent heat treatment on the final components.
1.2   prEN 10263-1:2013 is indispensable for this Part of EN 10263.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the dimensions, tolerances and physical constants of drawn hexagonal
steel bars used in aerospace construction.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 is applicable to round rod, round bars and wire with a diameter up to and including 100 mm, of non-alloy and alloy steel, intended for cold heading and cold extrusion and subsequent case hardening treatment.
1.2   prEN 10263-1:2013 is indispensable for this Part of EN 10263.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 is applicable to round rod, round bars and wire made of stainless steels intended for cold heading and cold extrusion having a diameter up to and including:
   25 mm for ferritic and austenitic-ferritic steels;
   50 mm for austenitic steels;
   100 mm for martensitic steels
1.2   prEN 10263-1:2013 is indispensable for the application of this part of EN 10263.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 is applicable to round rod and round bars and wire with a diameter up to and including 100 mm, of non-alloy and alloy steel, intended for cold heading, cold extrusion, subsequent quenching and tempering and induction hardening or flame hardening.
1.2   prEN 10263-1:2013 is indispensable for this Part of EN 10263.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 16120-2:2017 is applicable to general purpose steel wire rod for drawing and/or cold rolling.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    German language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the dimensions, tolerances and physical constants of ground round steel bars used in aerospace construction.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the dimensions, tolerances and physical constants of rolled rectangular
steel bars, used in aerospace construction.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the dimensions, tolerances and physical constants of drawn and/or descaled round steel bars used in aerospace construction.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 16120-1:2017 series is applicable to wire rod of non-alloy steel intended for wire drawing and/or cold rolling. The cross-section can be circular, oval, square, rectangular, hexagonal, octagonal, half-round or another shape, generally with at least 5 mm nominal dimension, and with a smooth surface. ISO 16120-1:2017 specifies general requirements for non-alloy steel wire rod for conversion to wire. It is not applicable to products for which standards exist or are in development, for example: - steel wire rod intended for heat treatment; - free-cutting steel wire rod; - steel wire rod for cold heading and cold extrusion; - steel wire rod intended for the production of electrodes and products for welding; - steel wire rod for welded fabric for reinforcement for concrete; - steel wire rod for ball and roller bearings (see ISO 683‑17); - steel wire rod for wire for high fatigue strength mechanical springs, such as valve springs. In addition to the requirements of this document, the general technical delivery requirements specified in ISO 404 apply.

  • Standard
    27 pages
    English language
    sale 15% off
  • Standard
    27 pages
    French language
    sale 15% off

ISO 16120-4:2017 specifies requirements for wire rod for conversion to wire for special applications. It is applicable to non-alloy steel wire rod with improved characteristics intended for drawing and/or cold rolling.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    French language
    sale 15% off

ISO 16120-2:2017 is applicable to general purpose steel wire rod for drawing and/or cold rolling.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    French language
    sale 15% off

This document specifies the technical delivery conditions for hot and cold formed stainless steel bars for the construction of pressure equipment supplied in accordance with one of the process routes and surface finishes listed in Table 5.
The general technical delivery conditions in EN 10021 also apply.
NOTE   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 97/23/EC is limited to technical data of materials in this European Standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 97/23/EC are satisfied, needs to be done.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical delivery conditions for hot rolled weldable steel bars for the construction of pressure equipment for use at elevated temperatures.
The general technical delivery conditions in EN 10021 also apply to products supplied in accordance with this European Standard.
NOTE   Once this European Standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 97/23/EC is limited to technical data of materials in this European Standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive 97/23/EC are satisfied, needs to be done.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the technical delivery conditions for hot and cold formed stainless steel bars for the construction of pressure equipment supplied in accordance with one of the process routes and surface finishes listed in Table 5.
The general technical delivery conditions in EN 10021 also apply.
NOTE   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 97/23/EC is limited to technical data of materials in this European Standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 97/23/EC are satisfied, needs to be done.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical delivery conditions for hot rolled weldable steel bars for the construction of pressure equipment for use at elevated temperatures.
The general technical delivery conditions in EN 10021 also apply to products supplied in accordance with this European Standard.
NOTE   Once this European Standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 97/23/EC is limited to technical data of materials in this European Standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive 97/23/EC are satisfied, needs to be done.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 16120-3:2011 is applicable to wire rod made of low-carbon, low-silicon, rimmed and rimmed substitute steel with high ductility intended for drawing and/or cold rolling.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 16120-3:2011 is applicable to wire rod made of low-carbon, low-silicon, rimmed and rimmed substitute steel with high ductility intended for drawing and/or cold rolling.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
  • Standard
    6 pages
    Russian language
    sale 15% off

This document specifies general requirements and definitions for the performance characteristics of weldable reinforcing steel used for the reinforcement of concrete structures, delivered as finished products in the form of:
-   bars, coils (rod, wire) and de-coiled products;
-   sheets of factory-made machine-welded fabric;
-   lattice girders.
1.2   Steels according to this document have a ribbed, indented or smooth surface.
1.3   This document does not apply to:
-   non-weldable reinforcing steel;
-   galvanized reinforcing steel;
-   epoxy-coated reinforcing steel;
-   corrosion resistant reinforcing steel;
-   prestressing steels (see prEN 10138-1 to -4);
-   indented strip;
-   further processing, e.g. cutting or cutting and bending.

  • Standard
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day

The scope of this part of EN 10088 is to specify the technical delivery conditions for hot or cold formed bars, rods, wire, sections and bright products of standard and special grades of corrosion resisting stainless steels for construction purposes in addition to the general technical delivery conditions specified in EN 10021. This European Standard does not apply to components manufactured by further processing of the product forms listed in 1.1 with quality characteristics altered as a result of such further processing.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 20723:2004 specifies delivery requirements that apply to the surface condition of hot-rolled sections with nominal thickness between greater than or equal to 3 mm and less than or equal to 160 mm. It applies to all surfaces excluding edges.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    French language
    sale 15% off

This European Standard specifies the nominal dimensions and the tolerances on dimensions and shape of hot-rolled round steel bars.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the nominal dimensions and the tolerances on dimensions and shape of hot-rolled finished square steel bars for general purposes.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the nominal dimensions and the tolerances on dimensions and shape of hot-rolled steel hexagon bars.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Part of this European Standard specifies the nominal dimensions and the tolerances on dimensions and shape of hot rolled spring steel flat bars for ribbed and grooved spring leaves.
This standard is applicable only to steel flats produced from steel grades specified in EN 10089.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Part of this European Standard specifies the nominal dimensions and the tolerances on dimensions and shape of hot rolled steel flat bars for springs with three different types of profiles (A, B, and C). Formulas for calculation the moment of inertia are specified in annex A.
This standard is applicable only to spring steel flat bars produced from steel grades specified in EN 10089.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the nominal dimensions and the tolerances on dimensions and shape of hot-rolled round steel bars.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day