Standard Test Method for Determining the Capability of Roofing and Waterproofing Materials to Seal around Fasteners

SIGNIFICANCE AND USE
In some situations, penetration through asphalt-based roofing or waterproofing materials by fasteners is a required part of the material installation process or occurs during installation of other system components. When fasteners penetrate the material as a purposeful and planned part of the construction process, it is reasonable to expect that materials designed to limit migration of liquid water at the interface between the penetrating fastener and the material will do so. This qualitative test method provides a means to evaluate the ability of a material to limit water migration at fastener penetrations when tested under defined conditions.
SCOPE
1.1 This qualitative test method determines the capability of asphalt-based roofing or waterproofing material to seal around a fastener that penetrates the material and prevent transmission of liquid water through the material at the penetration under defined conditions.
1.2 This test method is provided for adoption by ASTM or other consensus-based roofing and waterproofing product specifications as a standardized means to evaluate capability to seal around a fastener. Performance of this test method after subjecting the product to conditioning intended to simulate environmental stresses and strains is not prohibited.
1.3 The text of this test method references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Apr-2011
Current Stage
Ref Project

Relations

Buy Standard

Standard
ASTM D7349/D7349M-11 - Standard Test Method for Determining the Capability of Roofing and Waterproofing Materials to Seal around Fasteners
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
REDLINE ASTM D7349/D7349M-11 - Standard Test Method for Determining the Capability of Roofing and Waterproofing Materials to Seal around Fasteners
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D7349/D7349M −11
StandardTest Method for
Determining the Capability of Roofing and Waterproofing
1
Materials to Seal around Fasteners
This standard is issued under the fixed designation D7349/D7349M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D3462 Specification for Asphalt Shingles Made from Glass
Felt and Surfaced with Mineral Granules
1.1 This qualitative test method determines the capability of
D5147 Test Methods for Sampling and Testing Modified
asphalt-based roofing or waterproofing material to seal around
Bituminous Sheet Material
a fastener that penetrates the material and prevent transmission
F1667 Specification for Driven Fasteners: Nails, Spikes, and
of liquid water through the material at the penetration under
Staples
defined conditions.
1.2 This test method is provided for adoption by ASTM or 3. Terminology
other consensus-based roofing and waterproofing product
3.1 Definitions—For definitions of terms used in this test
specifications as a standardized means to evaluate capability to
method, refer to Terminology D1079.
seal around a fastener. Performance of this test method after
subjecting the product to conditioning intended to simulate
4. Summary of Test Method
environmental stresses and strains is not prohibited.
4.1 The capability of asphalt-based roofing or waterproofing
1.3 The text of this test method references notes and materials to seal around a penetrating fastener and prevent the
footnotes which provide explanatory material. These notes and
passage of liquid water at the fastener/material interface is
footnotes (excluding those in tables and figures) shall not be determined by penetrating the material with a fastener, erecting
considered as requirements of the standard.
a water column over that penetration, and monitoring the
assembly for water passage for a period of time.
1.4 The values stated in either SI units or inch-pound units
are to be regarded separately as standard. The values stated in
4.2 The test method includes protocols that establish levels
each system may not be exact equivalents; therefore, each for the test method parameters. The protocol used to evaluate
system shall be used independently of the other. Combining
a material is designated in a standard specification for the
values from the two systems may result in non-conformance
material or by the user of this test method.
with the standard.
5. Significance and Use
1.5 This standard does not purport to address all of the
5.1 In some situations, penetration through asphalt-based
safety concerns, if any, associated with its use. It is the
roofing or waterproofing materials by fasteners is a required
responsibility of the user of this standard to establish appro-
part of the material installation process or occurs during
priate safety and health practices and determine the applica-
installation of other system components. When fasteners pen-
bility of regulatory limitations prior to use.
etrate the material as a purposeful and planned part of the
construction process, it is reasonable to expect that materials
2. Referenced Documents
designed to limit migration of liquid water at the interface
2
2.1 ASTM Standards:
between the penetrating fastener and the material will do so.
D1079 Terminology Relating to Roofing and Waterproofing
This qualitative test method provides a means to evaluate the
ability of a material to limit water migration at fastener
penetrations when tested under defined conditions.
1
This test method is under the jurisdiction ofASTM Committee D08 on Roofing
andWaterproofing and is the direct responsibility of Subcommittee D08.02 on Steep
6. Apparatus
Roofing Products and Assemblies.
Current edition approved May 1, 2011. Published May 2011. Originally
6.1 Specimen Roller—Aroller having a mass of 11.8 kg [26
approved in 2008. Last previous edition approved in 2010 as D7349/D7349M – 10.
lb] 60.5 %, diameter of 125 mm [5 in.] 65 %, and width of
DOI: 10.1520/D7349_D7349M-11.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or 125 mm [5 in.] 65%.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
6.2 Water Column Container—A4 L [1 gal] can with the
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. bottom cut out.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D7349/D7349M−11
6.3 Sealant—Any commercially-available sealant suitable 9.4 Place two pieces of lumber, oriented paralle
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D7349/D7349M–10 Designation: D7349/D7349M – 11
Standard Test Method for
Determining the Capability of Roofing and Waterproofing
1
Materials to Seal around Fasteners
This standard is issued under the fixed designation D7349/D7349M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This qualitative test method determines the capability of asphalt-based roofing or waterproofing material to seal around a
fastener that penetrates the material and prevent transmission of liquid water through the material at the penetration under defined
conditions.
1.2 This test method is provided for adoption by ASTM or other consensus-based roofing and waterproofing product
specifications as a standardized means to evaluate capability to seal around a fastener. Performance of this test method after
subjecting the product to conditioning intended to simulate environmental stresses and strains is not prohibited.
1.3 The text of this test method references notes and footnotes which provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the standard.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D1079 Terminology Relating to Roofing and Waterproofing
D3462 Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules
D5147 Test Methods for Sampling and Testing Modified Bituminous Sheet Material
F1667 Specification for Driven Fasteners: Nails, Spikes, and Staples
3. Terminology
3.1 Definitions—For definitions of terms used in this test method, refer to Terminology D1079.
4. Summary of Test Method
4.1 The capability of asphalt-based roofing or waterproofing materials to seal around a penetrating fastener and prevent the
passage of liquid water at the fastener/material interface is determined by penetrating the material with a fastener, erecting a water
column over that penetration, and monitoring the assembly for water passage for a period of time.
4.2 The test method includes protocols that establish levels for the test method parameters. The protocol used to evaluate a
material is designated in a standard specification for the material or by the user of this test method.
5. Significance and Use
5.1 In some situations, penetration through asphalt-based roofing or waterproofing materials by fasteners is a required part of
the material installation process or occurs during installation of other system components. When fasteners penetrate the material
as a purposeful and planned part of the construction process, it is reasonable to expect that materials designed to limit migration
of liquid water at the interface between the penetrating fastener and the material will do so. This qualitative test method provides
a means to evaluate the ability of a material to limit water migration at fastener penetrations when tested under defined conditions.
1
This test method is under the jurisdiction of ASTM Committee D08 on Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.02 on Steep
Roofing Products and Assemblies.
Current edition approved Aug.May 1, 2010.2011. Published August 2010.May 2011. Originally approved in 2008. Last previous edition approved in 20082010 as
D7349–08a.D7349/D7349M – 10. DOI: 10.1520/D7349_D7349M-101.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ---------------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.