iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F711-02(2007)

(Specification)

Standard Specification for Fiberglass-Reinforced Plastic (FRP) Rod and Tube Used in Live Line Tools

Standard Specification for Fiberglass-Reinforced Plastic (FRP) Rod and Tube Used in Live Line Tools

ABSTRACT
This specification covers the technical characteristics of and test methods for insulating rods and foam-filled tubes made from fiberglass-reinforced plastic (FRP) that are intended for use in live line tools. This specification does not include insulating foam-filled tubes and rods made from other materials, as well as fittings and attachments to the rods and foam-filled tubes for complete tools are not covered in this specification. The rods and tubes shall undergo four types of tests, namely: design test, sample test, routine test, and acceptance test. Tests shall be conducted to evaluate the following mechanical and electrical properties: wicking, bending deflection, horizontal crush, tension, shear, compression, modulus of elasticity, and mechanical aging; and dielectric current and leakage.
SCOPE
1.1 This specification covers insulating rods and foam-filled tubes made from fiberglass-reinforced plastic (FRP) that are intended for use in live line tools.
1.2 This specification does not include insulating foam-filled tubes and rods from other materials. Specifications for fittings and attachments to rods and foam-filled tubes for complete tools are not covered in this specification.
1.3 This specification establishes the technical characteristics that the tubes and rods must satisfy.
The following safety hazards caveat pertains only to the test method portion, Section 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Sep-2007
ICS
13.260 - Protection against electric shock. Live working
Technical Committee
F18 - Electrical Protective Equipment for Workers
Drafting Committee
F18.35 - Tools & Equipment
Current Stage
Ref Project

Relations

Replaces
ASTM F711-02 - Standard Specification for Fiberglass-Reinforced Plastic (FRP) Rod and Tube Used in Live Line Tools
Effective Date
01-Oct-2007
Replaced By
ASTM F711-02(2013) - Standard Specification for Fiberglass-Reinforced Plastic (FRP) Rod and Tube Used in Live Line Tools 
Effective Date
01-Nov-2013
Referred By
ASTM F3121/F3121M-17(2022) - Standard Guide for In-Service Inspection, Maintenance, and Electrical Testing of Hand-Held Live-Line Insulating Tools (Fiberglass-Reinforced Plastic (FRP))
Effective Date
01-Oct-2007
Referred By
ASTM F1564-13(2019)e1 - Standard Specification for Structure-Mounted Insulating Work Platforms for Electrical Workers
Effective Date
01-Oct-2007
Referred By
ASTM F1701-12(2018) - Standard Specification for Unused Rope with Special Electrical Properties
Effective Date
01-Oct-2007
Referred By
ASTM F1825-03(2019) - Standard Specification for Clampstick Type Live Line Tools
Effective Date
01-Oct-2007

Buy Standard

ASTM F711-02(2007) - Standard Specification for Fiberglass-Reinforced Plastic (FRP) Rod and Tube Used in Live Line ToolsASTM F711-02(2007) - Standard Specification for Fiberglass-Reinforced Plastic (FRP) Rod and Tube Used in Live Line Tools
PreviousNext
Technical specification
ASTM F711-02(2007) - Standard Specification for Fiberglass-Reinforced Plastic (FRP) Rod and Tube Used in Live Line Tools
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F711 −02(Reapproved 2007)
Standard Specification for
Fiberglass-Reinforced Plastic (FRP) Rod and Tube Used in
1
Live Line Tools
ThisstandardisissuedunderthefixeddesignationF711;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.1.2 design test—atypeoftestmadeonasampletreatedas
representative of an industrial product. These tests will not
1.1 Thisspecificationcoversinsulatingrodsandfoam-filled
generally be repeated in quantity production.
tubes made from fiberglass-reinforced plastic (FRP) that are
3.1.3 insulating tubes and rods—fiberglass-reinforced plas-
intended for use in live line tools.
tic (FRP) products manufactured using processes so that the
1.2 This specification does not include insulating foam-
tubes and rods produced will meet the electrical and mechani-
filled tubes and rods from other materials. Specifications for
cal tests prescribed in this specification.
fittings and attachments to rods and foam-filled tubes for
3.1.4 interior foam-filled tube—homogeneous unicellular
complete tools are not covered in this specification.
thermosetting foam filling with closed cells blown with non-
1.3 This specification establishes the technical characteris-
combustible gases. The foam filling shall be bonded to the
tics that the tubes and rods must satisfy.
interior tube wall. The foam filling should be free of voids,
1.4 The following safety hazards caveat pertains only to the
separations, holes, cracks, etc.
test method portion, Section 12, of this specification.This
3.1.5 routine test—a type of test made regularly on produc-
standard does not purport to address all of the safety concerns,
tion material.
if any, associated with its use. It is the responsibility of the user
3.1.6 visual inspection—a visual check made to detect
of this standard to establish appropriate safety and health
constructional defects.
practices and determine the applicability of regulatory limita-
tions prior to use.
4. Ordering Information
4.1 Outside Diameter Sizes—Foam-filled FRP tube and
2. Referenced Documents
solid FRP rod shall meet the outside diameter dimensions
2
2.1 ASTM Standards:
shown in Table 1.The tolerances shown will assist in ensuring
D149Test Method for Dielectric Breakdown Voltage and
interchangeability with interfacing equipment.
DielectricStrengthofSolidElectricalInsulatingMaterials
4.2 Inspection of the material shall be agreed upon between
at Commercial Power Frequencies
the purchaser and the seller as part of the purchase contract.
D638Test Method for Tensile Properties of Plastics
D695Test Method for Compressive Properties of Rigid
5. Materials and Manufacture
Plastics
5.1 Except for those test methods leading to destruction,
neither the FRP tube, foam, or the bond between them shall
3. Terminology
deteriorate during the prescribed mechanical and electrical
3.1 Definitions of Terms Specific to This Standard:
tests of this specification.
3.1.1 acceptance test—a type of test made at the option of
6. Physical Requirements
the purchaser.
6.1 The materials shall conform to the diameters prescribed
in Table 1 for tube and rod.
1
This specification is under the jurisdiction of ASTM Committee F18 on
6.2 The standard sizes listed by nominal diameter are
Electrical Protective Equipment for Workers and is the direct responsibility of
recommended and do not preclude the manufacture of other
Subcommittee F18.35 on Tools & Equipment.
sizes or shapes.
Current edition approved Oct. 1, 2007. Published October 2007. Originally
approved in 1981. Last previous edition approved in 2002 as F711–02. DOI:
7. Weight
10.1520/F0711-02R07.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
7.1 It has not been found necessary to specify the weight of
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
the product produced under this specification in order for it to
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. comply with performance requirements.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F711−02 (2007)
TABLE 1 Standard Tube and Rod Outside Diameters
routine tube
routine rod
Nominal Diameter Min Diameter Max Diameter
TYPE
in. (mm) in. (mm) in. (mm)
10.2 Electrical:
Tube 1 (25.4) 0.98 (24.9) 1.02 (25.9)
Test Type Material
1
1 ⁄4 (31.8) 1.22 (31.0) 1.27 (32.3)
Dielectric current (leakage) design rod
1
1 ⁄2 (38.1) 1.47 (37.3) 1.53 (38.9)
(before moisture conditioning) design tube
3
1 ⁄4 (44.5) 1.73 (43.9) 1.78 (45.2)
Dielectric current
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F819-23(Terminology)
Standard Terminology Relating to Electrical Protective Equipment for Workers
  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F711-17(2022)(Specification)
Standard Specification for Fiberglass-Reinforced Plastic (FRP) Rod and Tube Used in Live Line Tools

ABSTRACT
This specification covers the technical characteristics of and test methods for insulating rods and foam-filled tubes made from fiberglass-reinforced plastic (FRP) that are intended for use in live line tools. This specification does not include insulating foam-filled tubes and rods made from other materials, as well as fittings and attachments to the rods and foam-filled tubes for complete tools are not covered in this specification. The rods and tubes shall undergo four types of tests, namely: design test, sample test, routine test, and acceptance test. Tests shall be conducted to evaluate the following mechanical and electrical properties: wicking, bending deflection, horizontal crush, tension, shear, compression, modulus of elasticity, and mechanical aging; and dielectric current and leakage.
SCOPE
1.1 This specification covers insulating rods and foam-filled tubes made from fiberglass-reinforced plastic (FRP) that are intended for use in live line tools.  
1.2 This specification does not include insulating foam-filled tubes and rods from other materials. Specifications for fittings and attachments to rods and foam-filled tubes for complete tools are not covered in this specification.  
1.3 This specification establishes the technical characteristics that the tubes and rods must satisfy.  
1.4 The following safety hazards caveat pertains only to the test method portion, Section 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    10 pages
    English language
    sale 15% off
ASTM
ASTM F2522-12(2022)(Test Method)
Standard Test Method for Determining the Protective Performance of a Shield Attached on Live Line Tools or on Racking Rods for Electric Arc Hazards

SIGNIFICANCE AND USE
5.1 This test method is intended for determining the heat attenuation factor (HAF) of a shield material and the effective heat attenuation factor (EHAF) at the location of the worker. This can be obtained by measuring the reduction of the arc incident energy levels caused by a shield attached on a live line tool (hot stick) or on a racking rod and designed for protection for workers exposed to electric arcs. The shield mechanical strength (SMS) can be obtained from visual observations of the high speed video recordings of each shot during HAF tests.  
5.1.1 Because of the variability of the arc exposure, different heat transmission values and pressure may result for individual sensors. The results of each sensor are evaluated in accordance with Section 12.  
5.2 This test method maintains the shield and the heat sensors in a static, vertical position and does not involve movement except that resulting from the exposure.  
5.3 This test method specifies a standard set of exposure conditions. Different exposure conditions may produce different results.
Note 1: In addition to the standard set of exposure conditions, other conditions representative of the expected hazard may be used and shall be reported should this data be cited.
SCOPE
1.1 This test method is used to determine the heat attenuation factor (HAF), the effective heat attenuation factor (EHAF), and the shields mechanical strength (SMS) of a shield attached on live line tools or racking rods intended for protection of workers exposed to electric arcs.  
1.2 The materials used in this test method of worker protection are in the form of a shield attached on live line tools or on the racking rods.  
1.3 The protective shield described in this test method shall be transparent and shall be easily attached and removed from live line tools or from racking rods.  
1.4 The protective shield described in this test method has 24-in. (0.61-m) diameter and can be used for most applications, however for special cases, the shield can have different sizes to suit the protective requirements of the application.  
1.5 This standard shall be used to measure and describe the properties of materials, products, or assemblies in response to incident energies (thermal-convective, and radiant and pressure wave) generated by an electric arc under controlled laboratory conditions and does not purport to predict damage from light, resultant pressure impact other than the pressure and thermal aspects measured.  
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.7 This standard shall not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire assessment, which takes into account all of the factors, which are pertinent to an assessment of the fire hazard of a particular end use.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.For specific precautions, see Section 7.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM F3121/F3121M-17(2022)(Guide)
Standard Guide for In-Service Inspection, Maintenance, and Electrical Testing of Hand-Held Live-Line Insulating Tools (Fiberglass-Reinforced Plastic (FRP))

SIGNIFICANCE AND USE
3.1 Compliance with this guide should confirm known and acceptable quality of hand-held insulating live-line tools manufactured using fiberglass meeting Specification F711. The guidance herein is to be considered as a minimum requirement.  
3.2 The user of this type of protective equipment should be knowledgeable of and instructed in the correct and safe inspection and use of this equipment.
SCOPE
1.1 This guide provides recommendations for in-service inspection, maintenance, and electrical testing of hand-held insulating live-line tools.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    5 pages
    English language
    sale 15% off
ASTM
ASTM F2621/F2621M-22(Practice)
Standard Practice for Evaluating Response Characteristics of Safety Products in an Electric Arc Exposure

SIGNIFICANCE AND USE
5.1 This practice can be used for a range of purposes including incident replication, development of improved arc rated protective products, and the determination of the response characteristics and design integrity of new or used arc rated finished products intended for use as protection for workers exposed to electric arcs.  
5.1.1 In-service garments can have very different wash and wear histories. Caution must be used when applying test results from a particular used garment. Factors to consider include the garments’ wear histories, work environments, and tasks for which the garments were worn; the methods and facilities for garment maintenance; the number of launderings or processings the garments have been subjected to; and other factors that could impact the protective performance of different garments. Test results from specific used garments should be considered only an approximation of results that might be obtained from other used garments of the same type.  
5.1.2 When using the practice for evaluating flame resistance, great care should be taken since ignition by electric arc is a statistical phenomenon. An exposure of 20 cal/cm2 has been consistently shown to evaluate most ignitable materials but some may require higher energy to reach the breakopen point of the fabric depending on coatings or specific fiber types. Consider using a vertical flame test such as Test Method D6413 to evaluate for ignition and use this practice for illustration.  
5.2 This practice maintains the specimen in a static, vertical position and does not involve movement except that resulting from the exposure.
SCOPE
1.1 This practice identifies protocols for use in conducting arc testing on finished products intended for use as thermal protection by workers who may be exposed to electric arc hazards.  
1.1.1 The practice is also used for other components which can be exposed to electric arc, but which do not require an arc rating.
1.1.1.1 If items are tested and they do not meet the appropriate standard, it is the responsibility of the specimen submitter to provide this information for indication in the test report.  
1.2 Arc Rated protective items are typically tested using this practice to evaluate the performance of the interface area between the product and the other arc flash PPE or to evaluate zippers and other findings.  
1.3 This practice does not establish an arc rating for any product. Other ASTM test methods are to be used when applicable such as ASTM F1959/F1959M, F2178, and F2675.  
1.4 This practice is not intended to produce an arc rating and does not replicate in all types of arc exposures.  
1.5 This practice is used with the following standards:  
1.5.1 Protective fabric materials receive arc ratings from Test Method F1959/F1959M.  
1.5.2 Face protective products receive arc ratings from Test Method F2178.  
1.5.3 Gloves receive arc ratings from Test Method F2675.  
1.5.4 Rainwear materials, findings and closures are specified by Specification F1891.  
1.5.5 Garments are specified by Specification F1506.  
1.6 The test specimens used in this practice are typically in the form of arc-rated finished products. These arc-rated finished products may include, but are not limited to, single layer garments, multi-layer garments or ensembles, cooling vests, gloves, sleeves, chaps, rainwear, balaclavas, faceshields, and hood assemblies with hood shield windows. Non-arc rated finished products may be included when part of a flame-resistant system, or for evaluating heat transmission through the finished product for incident reenactment, or for evaluation of products needed but not available as arc rated (such as respirators, etc.)  
1.7 The arc rated finished product specimens are new products as sold or products which have been used for the intended purpose for a designated time.  
1.8 This practice is used to determine the response characteristics or design integrity of arc-ra...

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM F1506-22(Specification)
Standard Performance Specification for Flame Resistant and Electric Arc Rated Protective Clothing Worn by Workers Exposed to Flames and Electric Arcs

ABSTRACT
This performance specification covers the design characteristics and associated test methods that relate specifically to the flame resistance of textile materials used in the fabrication of basic protection level occupational apparel worn by electrical workers who are exposed to momentary electric arc and related thermal hazards such as exposure to open flame and radiant heat. When evaluated in accordance with the test procedures enlisted herein, knit fabrics and woven fabrics of different fabric weights shall conform to individually specified values of the following properties: colorfastness such as laundering shade change, dry-cleaning shade change, and dimensional change; initial flammability characteristics and flammability characteristics after 25 washes/dry-cleaning such as char length and afterflame time; and arc test rating. Knit fabrics shall additionally be tested and adhere accordingly to bursting strength characteristics. Conversely, woven fabrics shall also be tested and adhere accordingly to breaking load, tear resistance, and seam slippage characteristics.
SCOPE
1.1 This performance specification identifies minimum performance requirements to determine the (a) arc rating of fabrics, (b) flame resistance of fabrics and subassemblies, (c) mechanical durability of the fabrics and subassemblies, (d) the minimum garment construction and performance requirements, and (e) the garment labeling requirements for the completed protective clothing worn by workers exposed to flames and electric arcs.  
1.1.1 The minimum requirements for garment labeling are intended to provide end users with adequate information to select garments with the appropriate arc rating.  
1.1.2 End users are required to perform an assessment to determine the level of hazard and the required arc rating of the protective clothing for their individual hazards.
1.1.2.1 The end user risk assessments are outside the scope of this standard.  
1.2 This performance specification does not address coated or laminated protective clothing commonly used for rainwear applications in an arc hazard environment. Performance requirements related to this category of protective clothing are detailed in Specification F1891.  
1.3 This performance specification does not address hand protection. Performance and test requirements related to hand protection are detailed in OSHA 1910.138, Specification D120, and Test Method F2675/F2675M.  
1.4 The care and maintenance requirements for laundering electric arc flash protective clothing are outside the scope of this standard. Refer to Guides F1449 or F2757 related to industrial or home laundering.  
1.5 This standard should be used to evaluate and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions. It should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions.  
1.5.1 The results of this evaluation may be used as elements of a fire-risk assessment that takes into account all of the factors that are pertinent to an assessment of the fire hazard of a particular end use.  
1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.7 The following precautionary caveat pertains only to the test methods portion, Section 7, of this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and...

  • Technical specification
    12 pages
    English language
    sale 15% off
  • Technical specification
    12 pages
    English language
    sale 15% off
ASTM
ASTM D120-22(Specification)
Standard Specification for Rubber Insulating Gloves

ABSTRACT
This specification covers manufacturing and testing of rubber insulating gloves for protection of workers from electrical shock. Two types of gloves are provided and are designated as Type I, non-resistant to ozone, and Type II, resistant to ozone. Six classes of gloves, differing in electrical characteristics, are provided and are designated as Class 00, Class 0, Class 1, Class 2, Class 3, and Class 4. The following tests shall be performed: ac proof test; ac breakdown test; ac moisture absorption/proof test; dc proof test; dc breakdown test; ozone resistance test; chemical tests; tensile strength; tear resistance test; and puncture resistance test.
SCOPE
1.1 This specification covers manufacturing and testing of rubber insulating gloves for protection of workers from electrical shock.  
1.2 Two types of gloves are provided and are designated as Type I, non-resistant to ozone, and Type II, resistant to ozone.  
1.3 Six classes of gloves, differing in electrical characteristics, are provided and are designated as Class 00, Class 0, Class 1, Class 2, Class 3, and Class 4.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. See IEEE/ASTM SI 10.  
1.5 The following safety hazards caveat pertains only to the test method portion, Sections 16, 17, 18, and 19, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific warning statement, see 18.2.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM F479-06(2022)(Specification)
Standard Specification for In-Service Care of Insulating Blankets

ABSTRACT
This specification covers elastomeric seals (gaskets) used to seal the joints of plastic pipe used for gravity, low-pressure, and high-pressure applications. This refers to push-on joints which require no internal or external pressure to effect the initial seal. Tensile strength, elongation, hardness, compression set, accelerated aging, water immersion, ozone resistance, and force decay shall be tested to meet the requirements prescribed.This specification covers the in-service care, inspection, testing, and use voltage of insulating blankets for protection of workers from accidental contact with live electrical conductors, apparatus, or circuits. Blankets covered shall be designated as type I or type II; class 0, class 1, class 2, class 3, or class 4; style A or style B: type I - not resistant to ozone, made from a high-grade cis-1,4-polyisoprene rubber compound of natural or synthetic origin, properly vulcanized; and type II - ozone-resistant, made of any elastomer or combination of elastomeric compounds. Style A - constructed of the elastomers indicated under type I or type II, shall be free of any reinforcement; and style B - constructed of the elastomers indicated under type I or type II, shall incorporate a reinforcement. Electrical testing shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers the in-service care, inspection, testing, and use voltage of insulating blankets for protection of workers from accidental contact with live electrical conductors, apparatus, or circuits. The product requirements and acceptance testing are as shown in Specification D1048.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.See Section 6 and 8.2 for specific precautionary statements.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM F1505-16(2021)(Specification)
Standard Specification for Insulated and Insulating Hand Tools

ABSTRACT
This specification covers the testing and corresponding design and performance requirements for insulated and insulating hand tools used for working on, or in close proximity to, energized electrical apparatus or conductors operating at maximum voltage of 1000 V ac or 1500 V dc. The hand tools covered here are screwdrivers, wrenches, pliers, nippers, strippers, cable cutting tools, cable scissors, knives, and tweezers. These tools shall be evaluated via visual and dimensional checks, ambient temperature and extreme low temperature impact tests, dielectric tests, indentation tests, adhesion tests for insulating material coatings, flame resistance tests, and mechanical tests such as bending, torque, and locking tests. Routine tests, acceptance criteria, and quality assurance plan for these tools are considered as well.
SIGNIFICANCE AND USE
6.1 The performance and durability of the tools covered in this specification are not covered beyond those referenced in the applicable ASME, ANSI, or ISO standards and GGG specifications.
SCOPE
1.1 This specification covers the testing of insulated and insulating hand tools used for working on, or in close proximity to, energized electrical apparatus or conductors operating at maximum voltage of 1000 V ac or 1500 V dc.  
1.2 The specific use of these tools is beyond the scope of this specification.  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.4 The following precautionary caveat pertains to the test method portion only, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This specification does not purport to address all of the safety problems associated with the use of tools on, or in close proximity to, energized electrical apparatus.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    23 pages
    English language
    sale 15% off
ASTM
ASTM F1116-21(Test Method)
Standard Test Method for Determining Dielectric Strength of Dielectric Footwear

SIGNIFICANCE AND USE
4.1 Electrical contact injuries to workers may involve a current path through the feet of the worker. The footwear covered by this specification is dielectrically rated to provide additional insulation and isolation to the wearer. This test method will determine that dielectric footwear has dielectric integrity at the time of the test.
SCOPE
1.1 This test method covers testing to determine the “Dielectric Strength” of dielectric overfoot and overshoe footwear. Testing is done over the maximum possible area of the dielectric footwear without permitting flashover between electrodes.  
1.2 The use and maintenance of dielectric footwear is beyond the scope of this test method.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements appear in 5.2.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off