This document specifies a laboratory method for measuring the vibration at the handle of fastener
driving tools. It is a type test procedure for establishing the vibration value on the handle of a handheld power tool operating under a specified load.
This document is applicable to fastener driving tools driven pneumatically or by other means, using
nails, staples or pins.
This document is applicable to tools with single sequential actuation, contact actuation, contact
actuation with automatic reversion or continual contact actuation (see Figures 1 to 3).
This document is not applicable to tools operating in full sequential mode due to their much longer
intervals in between individual actuations. However, to provide an indication for comparison of
different tools of this type (see Figures 4 and 5), Annex C provides informative guidance.
NOTE Today current knowledge does not allow any conclusions regarding physiological and pathological
effects between isolated shocks and continuous shock sequences, and their repetition rates

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held power-driven angle and vertical grinders. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine fitted with a specified test wheel and run under no‑load conditions. The method has been established for surface grinding tasks only. Cutting and sanding generally create lower vibrations. It is intended that the results be used to compare different models of the same type of machine.
This document is applicable to hand-held machines (see Clause 5), driven pneumatically or by other means, intended for grinding, cutting-off and rough sanding, with bonded, coated and super-abrasive products and with wire brushes for use on all kinds of materials. It is not applicable to die grinders or straight grinders.
NOTE    To avoid confusion with the terms "power tool" and "inserted tool", machine is used for the former throughout this document.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day

TAN - // IEC Corrigendum

  • Corrigendum
    3 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day

This document specifies minimum values for Rockwell hardness and torsional strength for hand-operated wrenches and sockets. It covers the following three series of torsion torques: — Series A: usual box wrenches and socket wrenches; EXAMPLE 1 Reference nos. 1 1 02 01 0; 1 1 02 02 0 and 1 1 02 02 1; 1 1 02 03 0; 1 1 02 04 0; 1 1 02 05 0; 1 1 02 06 0; 1 1 02 09 0; 1 1 02 10 0; 1 1 02 11 0; 1 1 02 12 0; 1 1 02 13 0 and 1 1 02 13 1; 1 1 02 14 0; 1 1 02 15 0; 1 1 08 01 0; 1 1 08 02 0. — Series C: open end wrenches; EXAMPLE 2 Reference nos. 1 1 01 01 0; 1 1 01 01 1; 1 1 01 02 0; 1 1 01 03 0; 1 1 01 04 0. — Series E: hand-operated square drive sockets. EXAMPLE Reference nos. 2 1 02 01 0 and 2 1 02 01 1. NOTE The wrenches and sockets mentioned above are listed under their respective reference numbers in ISO 1703.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off

This document specifies hardness and minimum torsional strength for machine-operated square drive sockets in accordance with ISO 2725-2 intended for use with impact wrenches. EXAMPLE Reference nos. 2 2 02 01 0; 2 2 02 02 0; 5 2 00 04 0. NOTE The sockets mentioned above are listed under their respective reference numbers in ISO 1703.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off

Based on IEC corrigendum

  • Corrigendum
    3 pages
    French language
    sale 10% off
    e-Library read for
    1 day

This document specifies the design, construction, guidance on use and maintenance of a dynamic loading device for the following categories of hand-held power tools: — percussive; — rotary-percussive. The device can be used when measurements are being made for vibration and noise including when required for specification in test standards.

  • Technical report
    31 pages
    English language
    sale 15% off
  • Technical report
    32 pages
    French language
    sale 15% off

This document is applicable to insulated, insulating and hybrid hand tools used for working
live or close to live parts at nominal voltages up to 1 000 V AC and 1 500 V DC.
The products designed and manufactured according to this document contribute to the safety
of the users provided they are used by skilled persons, in accordance with safe methods of
work and the instructions for use (where appropriate).

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 1703:2018 gives a nomenclature in English of assembly tools for screws and nuts. NOTE Annex A provides the technically equivalent terms in French, one of the other official ISO languages. In addition, this document gives the equivalent terms in German, Italian, Spanish and Swedish (see Annex B). These terms are published under the responsibility of the member bodies for Germany (DIN), Italy (UNI), Spain (UNE) and Sweden (SIS) and are given for information only. However, only the English and French terms can be considered as ISO terms.

  • Standard
    43 pages
    English language
    sale 15% off
  • Standard
    44 pages
    French language
    sale 15% off

ISO 2725-3:2017 specifies dimensions, designation, and marking of machine-operated "non-impact" square drive sockets. NOTE Machine-operated "non-impact" square drive sockets covered by this document are the ones identified in ISO 1703 under reference numbers 2 2 02 01 0.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off

ISO 2725-2:2017 specifies dimensions, designation, and marking of machine-operated "impact" square drive sockets with operating end having a hexagonal or double hexagonal form in accordance with ISO 1174‑2. NOTE Machine-operated "impact" square drive sockets covered by this document are the ones identified in ISO 1703 under reference numbers 2 2 02 01 0. ISO 2725-2:2017 does not cover technical specifications for these products. Technical specifications are given in ISO 1711‑2.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    French language
    sale 15% off

2013-10-02 EMA: Draft for //ENQ received in ISO/CS (see notification of 2013-10-02 in dataservice).

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

2013-10-02 EMA: Draft for //ENQ received in ISO/CS (see notification of 2013-10-02 in dataservice).

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 2351-3:2014 prescribes the technical specifications for machine-operated screwdriver bits for hexagon socket screws, listed in ISO 1703 under reference number 3 2 03 01 0. It applies to bits with male hexagon drive or with cylindrical flat-end drive as defined in ISO 1173 and to tips for screwdrivers as defined in ISO 2936. It also gives recommended combinations between tips and bits.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    French language
    sale 15% off

ISO 28927-12:2012 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held power driven portable die grinders. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of the machines where operating under type test conditions. It is intended that the results be used to compare different models of the same type of machine.
ISO 28927-12:2012 is applicable to hand-held machines, driven pneumatically or by other means, equipped with a collet and intended for deburring operations using hard metal burrs or mounted points, on different materials ranging from hard steel to plastics. It is also applicable to low-speed die grinders using flap wheels or cylindrical sleeves.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day

DOR should have been 2012-07-20.
2011-12-06 EMA: Draft for // vote received in ISO/CS (see notification of 2011-12-02 in dataservice).
2010-08-09 EMA: WI transfered to consultant K. Chielens following e-mail from PM sent to dataservice on 2010-08-05.

  • Amendment
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60745-2-23:2012 applies to die grinders and small rotary tools for mounted accessories not exceeding 55 mm in diameter and mounted sanding accessories not exceeding 80 mm in diameter such as, threaded cones or plugs that are threaded on a mandrel with an unrelieved shoulder flange, mandrel mounted wheels and rotary files with a rated speed not exceeding a peripheral speed of the accessory of 80 m/s at rated capacity. This part 2 is to be used in conjunction with the latest edition of IEC 60745-1 and its amendments. It was established on the basis of the fourth edition (2006) of that standard. This standard does not apply to straight and vertical grinders utilizing flanges for driving an abrasive accessory. Those tools are covered by IEC 60745-2-3. Keywords: Die grinders, rotary tools, grinding, sanding.
This publication is to be read in conjunction with IEC 60745-1:2006.

  • Standard
    33 pages
    English and French language
    sale 15% off

This document provides the basis for the drafting of vibration test codes for hand-held and hand-guided powerdriven machinery. It specifies the determination of hand-transmitted vibration emission in terms of frequencyweighted root-mean-square (r.m.s.) acceleration during type testing. For machines where vibration test codes do not exist, it may also be used for determination of emission values and contains sufficient guidance for designing an appropriate test. NOTE Vibration test codes based on this document should define measuring procedures which provide controlled, repeatable and reproducible results which are, as far as possible, in agreement with the vibration values measured at the machine-hand contact surfaces under real working conditions and for which the uncertainties of measurement are quantified. This document is applicable to hand-held power tools (e.g. chipping hammers, sanders), hand-guided powered machines (e.g. lawn mowers, single-axle tractors, vibratory rollers) and other types of powered machines fitted with handles, guiding beams or similar means of control. It is applicable to machinery of all power sources (electrical, hydraulic, pneumatic, internal combustion engine, etc.). It does not apply to fixed machinery in which the vibration is transmitted to the hands of the user through the workpiece. This document is not applicable to vibration transmitted from steering wheels or control levers of mobile machinery where the operator's position is on the machine, see EN 1032. It is restricted to translational vibration measured in three orthogonal directions at the hand-machine interface. This document should be applied with caution to machines producing single and repetitive shocks with a frequency of occurrence lower than 5 Hz. For such machines, it is not known whether frequency-weighted root-mean-square acceleration values are related to the risks to health and additional measurements may be required. When developing vibration test codes for such machines the information in CEN ISO/TS 15694 should be considered. This document is not applicable to vibration test codes published before the date of publication of this document by CEN and, when used as test code, to hand-held and hand-guided machinery manufactured before that date. This document does not present limits or recommended vibration values. It does not give any guidance or recommendations for determination of human exposure to vibration at the workplace. For such information, reference is made to EN ISO 5349-1 and EN ISO 5349-2.

  • Amendment
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 28927-10:2011 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held power driven percussive machines with and without rotary action [portable rock drills, plug hole drills, rotary hammers, breakers (e.g. pavement breakers, concrete breakers or road breakers), riveting hammers, chipping hammers, pick hammers or similar]. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine fitted with an inserted tool bit.
ISO 28927-10:2011 is applicable to hand-held machines, driven pneumatically or by other means, intended for making holes in hard materials, such as rock and concrete. It is also applicable to breakers intended to work downwards to break hard materials (concrete, rock, pavement, asphalt, etc.) and for hammers intended to work in any direction to perform riveting or chiselling work. It is not applicable to impact drills with direct mechanical impact mechanisms. ISO 28927-10:2011 is not applicable to jack leg type rock drills and push feed rock drills, which are hand guided (the feed force is not applied by hand, but by an additional device).

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 28927-10:2011 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held power driven percussive machines with and without rotary action [portable rock drills, plug hole drills, rotary hammers, breakers (e.g. pavement breakers, concrete breakers or road breakers), riveting hammers, chipping hammers, pick hammers or similar]. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine fitted with an inserted tool bit.
ISO 28927-10:2011 is applicable to hand-held machines, driven pneumatically or by other means, intended for making holes in hard materials, such as rock and concrete. It is also applicable to breakers intended to work downwards to break hard materials (concrete, rock, pavement, asphalt, etc.) and for hammers intended to work in any direction to perform riveting or chiselling work. It is not applicable to impact drills with direct mechanical impact mechanisms. ISO 28927-10:2011 is not applicable to jack leg type rock drills and push feed rock drills, which are hand guided (the feed force is not applied by hand, but by an additional device).

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of ISO 28927 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held stone hammers. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a stone hammer when operated in laboratory conditions. It is intended that the results be used to compare different models of the same type of machine. This part of ISO 28927 is applicable to engraving pens and stone hammers intended for use by stone masons, driven pneumatically or by other means. It is not applicable to demolition hammers or to chipping hammers primarily intended for use on metal or in construction.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 28927-11:2011 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held stone hammers. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a stone hammer when operated in laboratory conditions. It is intended that the results be used to compare different models of the same type of machine.
ISO 28927-11:2011 is applicable to engraving pens and stone hammers intended for use by stone masons, driven pneumatically or by other means. It is not applicable to demolition hammers or to chipping hammers primarily intended for use on metal or in construction.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 28927-4:2010 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of straight grinders. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine fitted with a specified test wheel and run under no-load conditions.
ISO 28927-4:2010 is applicable to hand-held machines, driven pneumatically or by other means, intended for grinding and surface finishing using straight grinding wheels type 1, tapered wheels type 4 and cylindrical plugs, e.g. of type 16 (cylindrical plug, tapered cone), 18 (cylindrical plug, flat end), 18R (cylindrical plug, rounded end) and 19 (cylindrical plug, taper-roll shaped), for use on all kinds of materials. It is not applicable to grinders used with wire brushes, nor is it applicable to die grinders where the inserted tool is mounted in a collet.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 28927-8:2009 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held, power-driven saws, polishing and filing machines with reciprocating action and small saws with oscillating or rotating action. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine run under specified test conditions. It is intended that the results be used to compare different models of the same type of machine.
ISO 28927-8:2009 is applicable to reciprocating files intended for surface finishing equipped with a file or polishing tool, saws intended for parting sheets, plaster for medical use or wood, or equipped with a saw blade for use on all kinds of materials, and small circular saws primarily intended for cutting metal or composite materials, whether driven pneumatically or by other means. It is not applicable to files that are normally used with one hand on the file blade, nor to large circular saws intended for cutting wood.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 28927-7:2009 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held, power-driven nibblers and shears. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine run under specified test conditions. It is intended that the results be used to compare different models of the same type of machine.
ISO 28927-7:2009 is applicable to nibblers and shears, driven pneumatically or by other means, intended for cutting sheet metal or composite materials.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 28927-6:2009 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held, power-driven rammers. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine run under specified test conditions. It is intended that the results be used to compare different models of the same type of machine.
ISO 28927-6:2009 is applicable to rammers, back-fill rammers, pawing rammers, sand rammers and stampers, driven pneumatically or by other means, intended for use in foundries, on building sites, etc., and with, for example, butts or peens made of cast iron or rubber, used for ramming of casting sand or in stamping work.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 28927-9:2009 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held, power-driven scaling hammers and needle scalers. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine run under specified test conditions. It is intended that the results be used to compare different models of the same type of machine.
ISO 28927-9:2009 is applicable to engraving pens, scabblers, scaling hammers and needle scalers, driven pneumatically or by other means, intended for paint, rust or scale removal with reciprocating work tools or needles and for all kinds of materials.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 28927-2:2009 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held power-driven wrenches, nutrunners and screwdrivers used for tightening and loosening threaded fasteners. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine when operating at a specified load. The method has been tested for fastening tasks only. It is intended that the results be used to compare different models of the same type of machine.
ISO 28927-2:2009 is applicable to hand-held machines, driven pneumatically or by other means, with impact or impulse action, of shut-off, ratchet or stall type, and of all designs — straight, pistol‑grip, angle or bow handle. It covers machines with 6,3 mm to 40 mm (1/4 in to 1½ in) male or female drive output shafts, as well as other geometries. It is not applicable to nutrunners designed to be used only in torque reaction arms.

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 28927-5:2009 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held, power-driven drills and impact drills. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a drill fitted with a drill bit. It is intended that the results be used to compare different models of the same type of machine.
ISO 28927-5:2009 is applicable to straight drills, drills with a pistol‑grip and angle drills intended for drilling holes with rotating or impact action in all kinds of materials (see Clause 5), driven pneumatically or by other means. It is not applicable to heavy-duty drills with a screw feed or drills driven by a combustion engine.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 28927-3:2009 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held, power-driven, portable polishers and rotary, orbital and random orbital sanders used for surface-finishing processes, not for material removal. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine when operating under type-test conditions. It is intended that the results be used to compare different models of the same type of machine.
ISO 28927-3:2009 is applicable to hand-held machines driven pneumatically or by other means. It is not applicable to straight grinders equipped with a sanding wheel or to belt sanders.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of ISO 28927 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held, power-driven rammers. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine run under specified test conditions. It is intended that the results be used to compare different models of the same type of machine. This part of ISO 28927 is applicable to rammers, back-fill rammers, pawing rammers, sand rammers and stampers (see Clause 5), driven pneumatically or by other means, intended for use in foundries, on building sites, etc., and with, for example, butts or peens made of cast iron or rubber, used for ramming of casting sand or in stamping work.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of ISO 28927 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held, power-driven nibblers and shears. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine run under specified test conditions. It is intended that the results be used to compare different models of the same type of machine. This part of ISO 28927 is applicable to nibblers and shears (see Clause 5), driven pneumatically or by other means, intended for cutting sheet metal or composite materials.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of ISO 28927 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held, power-driven drills and impact drills. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a drill fitted with a drill bit. It is intended that the results be used to compare different models of the same type of machine. This part of ISO 28927 is applicable to straight drills, drills with a pistol-grip and angle drills intended for drilling holes with rotating or impact action in all kinds of materials (see Clause 5), driven pneumatically or by other means. It is not applicable to heavy-duty drills with a screw feed or drills driven by a combustion engine.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of ISO 28927 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held, power-driven scaling hammers and needle scalers. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine run under specified test conditions. It is intended that the results be used to compare different models of the same type of machine. This part of ISO 28927 is applicable to engraving pens, scabblers, scaling hammers and needle scalers (see Clause 5), driven pneumatically or by other means, intended for paint, rust or scale removal with reciprocating work tools or needles and for all kinds of materials.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of ISO 28927 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held, power-driven saws, polishing and filing machines with reciprocating action and small saws with oscillating or rotating action. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine run under specified test conditions. It is intended that the results be used to compare different models of the same type of machine. This part of ISO 28927 is applicable to reciprocating files intended for surface finishing equipped with a file or polishing tool, saws intended for parting sheets, plaster for medical use or wood, or equipped with a saw blade for use on all kinds of materials, and small circular saws primarily intended for cutting metal or composite materials (see Clause 5), whether driven pneumatically or by other means. It is not applicable to files that are normally used with one hand on the file blade, nor to large circular saws intended for cutting wood.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This International Standard specifies test methods for the measurement, determination and declaration of the noise emission from hand-held non-electric power tools. It prescribes the loading and working conditions under which can be determined
the noise emission, under specified load conditions, expressed as the sound power level, andthe emission sound pressure level at the work station under specified load conditions.
This International Standard is applicable to typical hand-held non-electric power tools including rotary tools, orbital and random orbital sanders, rotary and non-rotary reciprocating and percussive tools and a variety of assembly tools. It is not applicable to cartridge-operated tools, fastener driving tools (e.g. nailers, staplers) or any tool powered by an internal combustion engine, nor is it applicable to breakers or other power tools which, when placed on the market, are required to meet the provisions of legislation specifying test methods and imposing limits on noise emission from, for example, equipment used outdoors.
NOTE The noise code could also be applied to other equipment such as winches, pneumatic motors, auto-feed drills and tappers, pumps, hydraulic motors and screw feed systems, provided their principles of operation were in accordance with those of pneumatic and hydraulic equipment.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 20643:2005 provides the basis for the drafting of vibration test codes for hand-held and hand-guided power-driven machinery. It specifies the determination of hand-transmitted vibration emission in terms of frequency-weighted root-mean-square (r.m.s.) acceleration during type testing. For machines where vibration test codes do not exist, it can also be used for determination of emission values and contains sufficient guidance for designing an appropriate test. It is applicable to hand-held power tools (e.g. chipping hammers, sanders), hand-guided powered machines (e.g. lawn mowers, single-axle tractors, vibratory rollers), and other types of powered machines fitted with handles, guiding beams or similar means of control, of all power sources (electrical, hydraulic, pneumatic, internal combustion engine, etc.). It is not applicable to fixed machinery in which the vibration is transmitted to the hands of the user through the workpiece, nor to vibration transmitted from steering wheels or control levers of mobile machinery where the operator's position is on the machine.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies test methods for the measurement, determination and declaration of the noise emission from hand-held non-electric power tools. It prescribes the loading and working conditions under which can be determined a) the noise emission, under specified load conditions, expressed as the sound power level, and b) the emission sound pressure level at the work station under specified load conditions.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document provides the basis for the drafting of vibration test codes for hand-held and hand-guided powerdriven machinery. It specifies the determination of hand-transmitted vibration emission in terms of frequencyweighted root-mean-square (r.m.s.) acceleration during type testing. For machines where vibration test codes do not exist, it may also be used for determination of emission values and contains sufficient guidance for designing an appropriate test. NOTE Vibration test codes based on this document should define measuring procedures which provide controlled, repeatable and reproducible results which are, as far as possible, in agreement with the vibration values measured at the machine-hand contact surfaces under real working conditions and for which the uncertainties of measurement are quantified. This document is applicable to hand-held power tools (e.g. chipping hammers, sanders), hand-guided powered machines (e.g. lawn mowers, single-axle tractors, vibratory rollers) and other types of powered machines fitted with handles, guiding beams or similar means of control. It is applicable to machinery of all power sources (electrical, hydraulic, pneumatic, internal combustion engine, etc.). It does not apply to fixed machinery in which the vibration is transmitted to the hands of the user through the workpiece. This document is not applicable to vibration transmitted from steering wheels or control levers of mobile machinery where the operator's position is on the machine, see EN 1032. It is restricted to translational vibration measured in three orthogonal directions at the hand-machine interface. This document should be applied with caution to machines producing single and repetitive shocks with a frequency of occurrence lower than 5 Hz. For such machines, it is not known whether frequency-weighted root-mean-square acceleration values are related to the risks to health and additional measurements may be required. When developing vibration test codes for such machines the information in CEN ISO/TS 15694 should be considered. This document is not applicable to vibration test codes published before the date of publication of this document by CEN and, when used as test code, to hand-held and hand-guided machinery manufactured before that date. This document does not present limits or recommended vibration values. It does not give any guidance or recommendations for determination of human exposure to vibration at the workplace. For such information, reference is made to EN ISO 5349-1 and EN ISO 5349-2.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 17066-2:2007 provides a vocabulary for the various types of hydraulic tools, fixed and portable and for the attachments that are used with them. The terms are given by category: general, tools for removing and shaping material, tools for assembly work.

  • Standard
    26 pages
    English language
    sale 15% off

ISO 2351-1:2007 prescribes the technical specifications for machine-operated screwdriver bits for slotted head screws. It applies to bits with male hexagon drive or with cylindrical flat end drive as defined in ISO 1173, and to tips for screwdrivers Type C as defined in ISO 2380-1. It also gives recommended combinations between tips and bits.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    French language
    sale 15% off

ISO 20643:2005 provides the basis for the drafting of vibration test codes for hand-held and hand-guided power-driven machinery. It specifies the determination of hand-transmitted vibration emission in terms of frequency-weighted root-mean-square (r.m.s.) acceleration during type testing. For machines where vibration test codes do not exist, it can also be used for determination of emission values and contains sufficient guidance for designing an appropriate test. It is applicable to hand-held power tools (e.g. chipping hammers, sanders), hand-guided powered machines (e.g. lawn mowers, single-axle tractors, vibratory rollers), and other types of powered machines fitted with handles, guiding beams or similar means of control, of all power sources (electrical, hydraulic, pneumatic, internal combustion engine, etc.). It is not applicable to fixed machinery in which the vibration is transmitted to the hands of the user through the workpiece, nor to vibration transmitted from steering wheels or control levers of mobile machinery where the operator's position is on the machine.

  • Standard
    15 pages
    English language
    sale 15% off
  • Standard
    16 pages
    French language
    sale 15% off

ISO 2380-2:2004 specifies the general requirements, lengths of blades and the marking of hand-operated screwdrivers for slotted-head screws as specified in ISO 4759-1.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off

ISO 2380-1:2004 specifies the shape/form, dimensions and designation of the tips of hand- and machine-operated screwdrivers for slotted-head screws. It also gives the technical specifications and test conditions for the screw-drivers and, in the case of hand-operated screwdrivers, specifies the test torque which the blade-to-handle connection shall withstand.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off

ISO 2351-2 prescribes the technical specifications for machine-operated screwdriver bits for cross-recessed head screws. It applies to bits with male hexagon drive or with cylindrical flat end drive as defined in ISO 1173, and to tips for screwdrivers as defined in ISO 8764-1. It also gives recommended combinations between tips and bits.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off