iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F467-13(2018)

(Specification)

Standard Specification for Nonferrous Nuts for General Use

Standard Specification for Nonferrous Nuts for General Use

ABSTRACT
This specification covers the requirements for commercial wrought nonferrous nuts in nominal thread diameters M6 to M36 inclusive in a number of alloys in common use and intended for general service applications. Materials shall be tested and shall conform to the chemical composition, hardness, proof stress, proof load, and tensile stress requirements.
SIGNIFICANCE AND USE
11.1 For purposes of determining compliance with the specified limits for requirements of the properties listed in this specification, an observed value or calculated value shall be rounded in accordance with Practice E29.
SCOPE
1.1 This specification covers the requirements for commercial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in diameter in a number of alloys in common use and intended for general service applications.  
1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F468.  
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1: This specification is the inch-pound companion to Specification F467M; therefore, no SI equivalents are presented in the specification.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
31-Aug-2018
ICS
21.060.20 - Nuts
Technical Committee
F16 - Fasteners
Drafting Committee
F16.04 - Nonferrous Fasteners
Current Stage
Ref Project

Relations

Refers
ASTM F606/F606M-16 - Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
Effective Date
01-Sep-2016
Refers
ASTM E18-17 - Standard Test Methods for Rockwell Hardness of Metallic Materials
Effective Date
01-Jul-2017
Refers
ASTM D3951-18 - Standard Practice for Commercial Packaging
Effective Date
01-May-2018
Refers
ASTM D3951-15 - Standard Practice for Commercial Packaging
Effective Date
01-Dec-2015
Refers
ASTM F468-15e1 - Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use
Effective Date
01-Dec-2015
Refers
ASTM F468-15 - Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use
Effective Date
01-Dec-2015
Refers
ASTM F606/F606M-14a - Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
Effective Date
01-Nov-2014
Refers
ASTM E18-18 - Standard Test Methods for Rockwell Hardness of Metallic Materials
Effective Date
01-Jul-2018
Refers
ASTM F1470-18 - Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
Effective Date
01-Feb-2018
Referred By
ASTM F1718-01(2019) - Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
Effective Date
01-Sep-2018
Referred By
ASTM F1370-92(2019)e1 - Standard Specification for Pressure-Reducing Valves for Water Systems, Shipboard
Effective Date
01-Sep-2018
Referred By
ASTM F468-23 - Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use
Effective Date
01-Sep-2018
Referred By
ASTM B745/B745M-15(2021) - Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains
Effective Date
01-Sep-2018
Referred By
ASTM C1802-23 - Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures
Effective Date
01-Sep-2018
Referred By
ASTM F1508-96(2021) - Standard Specification for Angle Style, Pressure Relief Valves for Steam, Gas, and Liquid Services
Effective Date
01-Sep-2018
Referred By
ASTM F1155-10(2019) - Standard Practice for Selection and Application of Piping System Materials
Effective Date
01-Sep-2018
Referred By
ASTM B746/B746M-22 - Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
Effective Date
01-Sep-2018

Buy Standard

ASTM F467-13(2018) - Standard Specification for Nonferrous Nuts for General UseASTM F467-13(2018) - Standard Specification for Nonferrous Nuts for General Use
PreviousNext
Technical specification
ASTM F467-13(2018) - Standard Specification for Nonferrous Nuts for General Use
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:F467 −13 (Reapproved 2018)
Standard Specification for
1
Nonferrous Nuts for General Use
ThisstandardisissuedunderthefixeddesignationF467;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* E18 Test Methods for Rockwell Hardness of Metallic Ma-
terials
1.1 This specification covers the requirements for commer-
E29 Practice for Using Significant Digits in Test Data to
cial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in
Determine Conformance with Specifications
diameterinanumberofalloysincommonuseandintendedfor
E34 Test Methods for Chemical Analysis of Aluminum and
general service applications.
3
Aluminum-Base Alloys (Withdrawn 2017)
1.2 Applicablebolts,capscrews,andstudsforusewithnuts
E38 Methods for Chemical Analysis of Nickel-Chromium
3
covered by this specification are covered by Specification
and Nickel-Chromium-Iron Alloys (Withdrawn 1989)
F468.
E53 Test Method for Determination of Copper in Unalloyed
Copper by Gravimetry
1.3 The values stated in inch-pound units are to be regarded
as standard. No other units of measurement are included in this E54 Test Methods for ChemicalAnalysis of Special Brasses
3
and Bronzes (Withdrawn 2002)
standard.
E55 Practice for Sampling Wrought Nonferrous Metals and
NOTE 1—This specification is the inch-pound companion to Specifica-
Alloys for Determination of Chemical Composition
tionF467M;therefore,noSIequivalentsarepresentedinthespecification.
E62 Test Methods for Chemical Analysis of Copper and
1.4 This international standard was developed in accor-
3
CopperAlloys(PhotometricMethods)(Withdrawn2010)
dance with internationally recognized principles on standard-
E75 Test Methods for Chemical Analysis of Copper-Nickel
ization established in the Decision on Principles for the
3
and Copper-Nickel-Zinc Alloys (Withdrawn 2010)
Development of International Standards, Guides and Recom-
E76 Test Methods for Chemical Analysis of Nickel-Copper
mendations issued by the World Trade Organization Technical
3
Alloys (Withdrawn 2003)
Barriers to Trade (TBT) Committee.
E92 Test Methods for Vickers Hardness and Knoop Hard-
ness of Metallic Materials
2. Referenced Documents
E101 TestMethodforSpectrographicAnalysisofAluminum
2
2.1 ASTM Standards:
and Aluminum Alloys by the Point-to-Plane Technique
3
B154 Test Method for Mercurous Nitrate Test for Copper
(Withdrawn 1996)
Alloys
E120 Test Methods for Chemical Analysis of Titanium and
3
B574 Specification for Low-Carbon Nickel-Chromium-
Titanium Alloys (Withdrawn 2003)
Molybdenum, Low-Carbon Nickel-Molybdenum-
E165 Practice for Liquid Penetrant Examination for General
Chromium, Low-Carbon Nickel-Molybdenum-
Industry
Chromium-Tantalum, Low-Carbon Nickel-Chromium-
E227 Test Method for Optical Emission Spectrometric
Molybdenum-Copper, and Low-Carbon Nickel-
Analysis of Aluminum and Aluminum Alloys by the
3
Chromium-Molybdenum-Tungsten Alloy Rod
Point-to-Plane Technique (Withdrawn 2002)
D3951 Practice for Commercial Packaging
E354 Test Methods for Chemical Analysis of High-
Temperature,Electrical,Magnetic,andOtherSimilarIron,
Nickel, and Cobalt Alloys
1
This specification is under the jurisdiction of ASTM Committee F16 on
E478 Test Methods for ChemicalAnalysis of CopperAlloys
Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous
E1409 Test Method for Determination of Oxygen and Nitro-
Fasteners.
gen in Titanium and TitaniumAlloys by Inert Gas Fusion
Current edition approved Sept. 1, 2018. Published September 2018. Originally
ε2
F468 Specification for Nonferrous Bolts, Hex Cap Screws,
approved in 1976. Last previous edition approved in 2013 as F467 – 13 . DOI:
10.1520/F0467-13R18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F467−13 (2018)
Socket Head Cap Screws, and Studs for General Use
Alloy Condition
F606/F606M Test Methods for Determining the Mechanica
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F594-22(Specification)
Standard Specification for Stainless Steel Nuts

ABSTRACT
This specification covers the requirements for stainless steel nuts in specified size, inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance. Seven groups of stainless steel alloys are covered, including ten austenitic, two ferritic, four martensitic, and one precipitation hardening: Group 1; Group 2; Group 3; Group 4; Group 5; Group 6; and Group 7. The finished fasteners shall meet the applicable mechanical properties. Chemical tests; mechanical tests; and corrosion resistance shall be performed to conform with the specified requirements.
SIGNIFICANCE AND USE
15.1 For the purposes of determining compliance with the specified limits for properties listed in this specification, an observed value or calculated value shall be rounded in accordance with Practice E29.
SCOPE
1.1 This specification covers the requirements for stainless steel nuts 0.25 to 1.50 in., inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.  
1.2 Seven groups of stainless steel alloys are covered, including ten austenitic, two ferritic, four martensitic, and one precipitation hardening.    
Group  
AlloysA  
ConditionB    
1  
304, 305, 304L
384, 18–9LW, 302HQC  
(CW)  
cold workedD    
2  
316, 316L  
(CW)  
cold workedD  
3  
321, 347  
(CW)  
cold workedD  
4  
430E  
(CW)  
cold workedD  
5  
410F  
(H)  
hardened and tempered    
6  
431  
(H)  
hardened and tempered  
7  
630  
(AH)  
aged hardened  
1.3 Supplementary requirements of an optional nature are provided, applicable only when agreed upon by the manufacturer and the purchaser at the time of the inquiry and order.  
1.4 Suitable bolts, hex cap screws, and studs for use with nuts included in this specification are covered by Specification F593. Unless otherwise specified, all bolts, hex cap screws, and studs used with these nuts shall conform to the requirements of Specification F593 and shall be of the same alloy group.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM F812/F812M-12(2022)e1(Specification)
Standard Specification for Surface Discontinuities of Nuts, Inch and Metric Series

ABSTRACT
This specification establishes allowable limits for the various types of surface discontinuities such as cracks that may occur during the manufacture and processing of metric-series nuts and inch-series nuts. The different types of surface discontinuities and allowable limits are presented in details. The nuts shall be inspected for surface discontinuities to meet the requirements prescribed. Cone proof load test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of metric-series nuts with nominal diameters 5 mm and larger and inch-series nuts with nominal diameters 1/4 in. and larger.  
1.2 The values stated in either SI (metric) or inch-pound units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.  
1.3 When the engineering requirements of the application necessitate control of surface discontinuities on nuts, the purchaser shall specify conformance to this ASTM specification in the original inquiry and purchase order.  
1.3.1 When the engineering requirements of the application necessitate that surface discontinuities on nuts be controlled within limits closer than those specified in this specification, the purchaser shall specify the applicable limits in the original inquiry and purchase order.  
1.4 The allowable limits established in this specification for metric nuts, with nominal diameters 5 to 24 mm inclusive, are essentially identical with requirements given in ISO/DIS 6157/II. There are no ISO standards for surface discontinuities on metric-series nuts with nominal diameters larger than 24 mm or on any inch-series nuts.  
1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM A563/A563M-21ae1(Specification)
Standard Specification for Carbon and Alloy Steel Nuts (Inch and Metric)

ABSTRACT
This specification covers chemical and mechanical requirements for eight property classes of hex and hex-flange carbon and alloy steel nuts for general structural and mechanical uses on bolts, studs, and other externally threaded parts. Materials shall be tested and the individual grades shall conform to specified values of material such as hardness and proof load, chemical, and mechanical requirements. Classes 8S3 and 10S3 nuts have atmospheric corrosion resistance and weathering characteristics comparable to those of the steels. The atmospheric corrosion resistance of these steels is substantially better than that of carbon steel with or without copper addition. When properly exposed to the atmosphere, these steels can be used bare (uncoated) for many applications.
SCOPE
1.1 This specification2 covers chemical and mechanical requirements for eleven grades of carbon and alloy steel nuts for general structural and mechanical uses on bolts, studs, and other externally threaded parts.  
Note 1: See Appendix X1 for guidance on suitable application of nut grades.  
1.2 The requirements for any grade of nut may, at the supplier's option, and with notice to the purchaser, be fulfilled by furnishing nuts of one of the stronger grades specified herein unless such substitution is barred in the inquiry and purchase order.  
1.3 Terms used in this specification are defined in Terminology F1789 unless otherwise defined herein.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    12 pages
    English language
    sale 15% off
ASTM
ASTM F901-20(Specification)
Standard Specification for Aluminum Transmission Tower Bolts and Nuts

ABSTRACT
This specification covers aluminum transmission tower bolts and nuts. Bolts shall be manufactured from alloy 2024 and nuts from alloy 6061 or 6262, and shall be cold formed, hot formed, or machined formed. Alloy materials for bolts and nuts shall conform to the chemical requirements of this specification. Bolts and nuts shall conform to the required tensile strength, dimensions, workmanship, finish, appearance, marking, packaging, and shipping. Test methods shall include chemical analysis, wedge tension test, shear test, and proof-stress test.
SCOPE
1.1 This specification covers aluminum structural bolts and nuts for use in the construction of aluminum transmission towers, substations, and similar aluminum structures.  
1.2 Diameters of bolts and nuts furnished to this specification are 5/8 , 3/4 , and 7/8 in.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM F836M-20(Specification)
Standard Specification for Style 1 Stainless Steel Metric Nuts (Metric)

ABSTRACT
This specification covers the chemical and mechanical requirements for style 1 stainless steel metric nuts. Groups and property classes of austenitic, ferritic, martensitic, and precipitation hardening stainless steel alloys are covered. Materials shall be cold-formed, hot-formed, or machined form, and shall conform to chemical, mechanical, dimensional and surface finish properties. Stainless steel shall also conform to heat treatment requirements depending on material grade. The material shall be capable of passing chemical, mechanical, and corrosion resistance tests in accordance to the specification. Product marking and packaging shall conform to the requirements of the specification.
SCOPE
1.1 This specification covers the chemical and mechanical requirements for stainless steel metric nuts with nominal thread diameters M1.6 through M36 and intended for use in engineering applications requiring general corrosion resistance.  
1.2 Eight groups of stainless steel alloys are covered, including three austenitic (Grades A1, A2, and A4), one ferritic (Grade F1), three martensitic (Grades C1, C3, and C4), and one precipitation hardening (Grade P1).  
1.3 Seventeen property classes are covered, including nine austenitic, one ferritic, six martensitic, and one precipitation hardening. The property classes with the permissible alloys for each are listed in Table 1.    
1.4 This specification is based in concept and content on ISO 3506. The chemical and mechanical requirements specified for all property classes, except as given in 1.4.1, are essentially identical with classes of the same designation in ISO 3506.  
1.4.1 This specification includes 13 of the 16 property classes covered in ISO 3506. Additionally, it includes property classes A1-70, A2–70, A4–70, A1–80, A2–80, and A4–80 for products with nominal thread diameters larger than M20; and four non-ISO property classes, C1-110, C4-110, C3-120, and P1-90.  
1.5 Supplementary requirements of an optional nature are provided, applicable only when agreed upon between the manufacturer and the purchaser at the time of the inquiry and order.  
1.6 Suitable bolts, hex cap screws, and studs for use with nuts included in this specification are covered by Specification F738M. Unless otherwise specified, all bolts, hex cap screws, and studs used with these nuts shall conform to the requirements of Specification F738M and shall be of the same alloy group.  
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM F436/F436M-19(Specification)
Standard Specification for Hardened Steel Washers Inch and Metric Dimensions

ABSTRACT
This specification covers the chemical, mechanical, and dimensional requirements for hardened steel washers for use with fasteners having nominal thread diameters of M12 through M100. These washers are intended for general-purpose mechanical and structural use with bolts, nuts, studs, and other internally and externally threaded fasteners. The types of washers covered here are: Type 1—washers made of carbon steel; and Type 3—washers made of weathering steel. Moreover, the styles of washers covered here are: circular washers, which are suitable for applications where sufficient space exists and angularity permits; beveled washers, which are square and rectangular with a beveled 1:6 surface for use with American Standard beams and channels; and clipped washers, which are circular or beveled for use where space limitations necessitate that one side be clipped. Steels to be used to manufacture the washers shall be produced by the open-hearth, basic-oxygen, or electric-furnace process. Each type and style of washer shall be suitably sampled, and should conform to specified values of chemical composition, Rockwell hardness, inside and outside diameter, thickness, and clipped width.
SCOPE
1.1 This specification covers the chemical, mechanical, and dimensional requirements for hardened steel washers for use with fasteners having nominal thread diameters of 1/4 through 4 in. and M12 through M100. These washers are intended for general-purpose mechanical and structural use with bolts, nuts, studs, and other internally and externally threaded fasteners. These washers are suitable for use with fasteners covered in Specifications A354, A449, A563, A563M, F959/F959M, and F3125.  
1.2 The washers are designated by type denoting the material, by style denoting the shape, and by inch or metric dimensions.  
1.2.1 The types of washers covered are:
1.2.1.1 Type 1—Carbon steel.
1.2.1.2 Type 3—Weathering steel.
1.2.1.3 This specification provides for furnishing Type 3 to chemical composition or a Corrosion Index (CRI) of 6 or higher at the suppliers option.  
1.2.2 The styles of washers covered are:
1.2.2.1 Circular—Circular washers in nominal sizes 1/4 through 4 in. and M12 through M100 suitable for applications where sufficient space exists and angularity permits.
1.2.2.2 Beveled—Beveled washers are square or rectangular, in nominal sizes 1/2 through 11/2 in., M12 through M16, with a beveled 1 to 6 ratio surface for use with American standard beams and channels.
1.2.2.3 Clipped—Clipped washers are circular or beveled for use where space limitations necessitate that one side be clipped.
1.2.2.4 Extra Thick—Extra thick washers are circular washers in nominal sizes 1/2 through 4 in., with a nominal thickness of 5/16 in. suitable for structural applications with oversized holes.  
1.3 Terms used in this specification are defined in Terminology F1789 unless otherwise defined herein.  
1.4 The values stated in either inch-pound units for inch fasteners and SI units for metric fasteners and are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM F467M-06a(2018)(Specification)
Standard Specification for Nonferrous Nuts for General Use (Metric)

ABSTRACT
This specification covers the requirements for commercial wrought nonferrous nuts in nominal thread diameters M6 to M36 inclusive in a number of alloys in common use and intended for general service applications. Materials shall be tested and shall conform to the chemical composition, hardness, proof stress, proof load, and tensile stress requirements.
SIGNIFICANCE AND USE
11.1 For purposes of determining compliance with the specified limits for requirements of the properties listed in this specification, an observed value or calculated value shall be rounded in accordance with Practice E29.
SCOPE
1.1 This specification covers the requirements for commercial wrought nonferrous nuts in nominal thread diameters M6 to M36 inclusive in a number of alloys in common use and intended for general service applications.  
1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F468M.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1: This specification is the metric companion of Specification F467.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM A194/A194M-23(Specification)
Standard Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both

ABSTRACT
This specification covers a variety of carbon, alloy, and martensitic and austenitic stainless steel nuts. These nuts are intended for high-pressure or high-temperature service, or both. Bars from which the nuts are made shall be hot-wrought. The material may be further processed by centerless grinding or by cold drawing. Austenitic stainless steel may be solution annealed or annealed and strain-hardened. Each alloy shall conform to the chemical composition requirements prescribed. Hardness tests, proof of load tests, and cone proof load tests shall be made to all nuts to meet the requirements specified.
SCOPE
1.1 This specification2 covers a variety of carbon, alloy, and martensitic stainless steel nuts in the size range 1/4 through 4 in. and metric M12 through M100 nominal. It also covers austenitic stainless steel nuts in the size range 1/4 in. and M12 nominal and above. These nuts are intended for high-pressure or high-temperature service, or both. Grade substitutions without the purchaser's permission are not allowed.  
1.2 Bars from which the nuts are made shall be hot-wrought. The material may be further processed by centerless grinding or by cold drawing. Austenitic stainless steel may be solution annealed or annealed and strain-hardened. When annealed and strain hardened austenitic stainless steel is ordered in accordance with Supplementary Requirement S1, the purchaser should take special care to ensure that 8.2.2, Supplementary Requirement S1, and Appendix X1 are thoroughly understood.  
1.3 Supplementary requirements of an optional nature are provided. These shall apply only when specified in the inquiry, contract, and order.  
1.4 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.  
1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Within the text, the SI units are shown in brackets.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    13 pages
    English language
    sale 15% off
  • Technical specification
    13 pages
    English language
    sale 15% off
ASTM
ASTM F594-22(Specification)
Standard Specification for Stainless Steel Nuts

ABSTRACT
This specification covers the requirements for stainless steel nuts in specified size, inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance. Seven groups of stainless steel alloys are covered, including ten austenitic, two ferritic, four martensitic, and one precipitation hardening: Group 1; Group 2; Group 3; Group 4; Group 5; Group 6; and Group 7. The finished fasteners shall meet the applicable mechanical properties. Chemical tests; mechanical tests; and corrosion resistance shall be performed to conform with the specified requirements.
SIGNIFICANCE AND USE
15.1 For the purposes of determining compliance with the specified limits for properties listed in this specification, an observed value or calculated value shall be rounded in accordance with Practice E29.
SCOPE
1.1 This specification covers the requirements for stainless steel nuts 0.25 to 1.50 in., inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.  
1.2 Seven groups of stainless steel alloys are covered, including ten austenitic, two ferritic, four martensitic, and one precipitation hardening.    
Group  
AlloysA  
ConditionB    
1  
304, 305, 304L
384, 18–9LW, 302HQC  
(CW)  
cold workedD    
2  
316, 316L  
(CW)  
cold workedD  
3  
321, 347  
(CW)  
cold workedD  
4  
430E  
(CW)  
cold workedD  
5  
410F  
(H)  
hardened and tempered    
6  
431  
(H)  
hardened and tempered  
7  
630  
(AH)  
aged hardened  
1.3 Supplementary requirements of an optional nature are provided, applicable only when agreed upon by the manufacturer and the purchaser at the time of the inquiry and order.  
1.4 Suitable bolts, hex cap screws, and studs for use with nuts included in this specification are covered by Specification F593. Unless otherwise specified, all bolts, hex cap screws, and studs used with these nuts shall conform to the requirements of Specification F593 and shall be of the same alloy group.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM F812/F812M-12(2022)e1(Specification)
Standard Specification for Surface Discontinuities of Nuts, Inch and Metric Series

ABSTRACT
This specification establishes allowable limits for the various types of surface discontinuities such as cracks that may occur during the manufacture and processing of metric-series nuts and inch-series nuts. The different types of surface discontinuities and allowable limits are presented in details. The nuts shall be inspected for surface discontinuities to meet the requirements prescribed. Cone proof load test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of metric-series nuts with nominal diameters 5 mm and larger and inch-series nuts with nominal diameters 1/4 in. and larger.  
1.2 The values stated in either SI (metric) or inch-pound units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.  
1.3 When the engineering requirements of the application necessitate control of surface discontinuities on nuts, the purchaser shall specify conformance to this ASTM specification in the original inquiry and purchase order.  
1.3.1 When the engineering requirements of the application necessitate that surface discontinuities on nuts be controlled within limits closer than those specified in this specification, the purchaser shall specify the applicable limits in the original inquiry and purchase order.  
1.4 The allowable limits established in this specification for metric nuts, with nominal diameters 5 to 24 mm inclusive, are essentially identical with requirements given in ISO/DIS 6157/II. There are no ISO standards for surface discontinuities on metric-series nuts with nominal diameters larger than 24 mm or on any inch-series nuts.  
1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off