ASTM F606/F606M-14a
(Test Method)Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
ABSTRACT
These test methods establishes the standard procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers and direct tension indicators, and rivets. For externally threaded fasteners, the mechanical tests describe the procedures for determining the following properties: product hardness; proof load by length measurement (Method 1), yield strength (Method 2), yield strength of austenitic stainless steel and nonferrous materials (Method 2A), and uniform hardness (Method 3); axial tension of full size products such as fasteners and studs; wedge tension of full size products such as fasteners and studs; tension of machined test specimens including yield point (by drop of the beam or halt of the pointer, autographic diagram, and total extension under load methods), yield strength (by offset, and extension under load methods), tensile strength, elongation, and reduction of area; and total extension at fracture. As for internally threaded fasteners including nonheat- and heat-treated nuts, tests are provided for the determination of product hardness, proof load, and cone proof load. Test for determining the surface and core hardnesses are, conversely, described for direct tension indicators, and through-hardened, carburized, stainless steel, and nonferrous washers. And finally, product hardness testing is described for rivets. The test method for determining embrittlement of metallic coated externally threaded fasteners is detailed as well.
SCOPE
1.1 These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers, direct tension indicators, and rivets.
1.2 Property requirements and the applicable tests for their determination are specified in individual product standards. In those instances where the testing requirements are unique or at variance with these standard procedures, the product standard shall specify the controlling testing requirements. In the absence of any specified test requirement(s), these test methods shall apply.
1.3 These test methods describe mechanical tests for determining the following properties:
Section
For Externally Threaded Fasteners:
3
Product Hardness
3.1
Proof Load
3.2.1
Method 1, Length Measurement
3.2.3
Method 2, Yield Strength
3.2.4
Method 3, Uniform Hardness
3.2.5
Axial Tension Testing of Full-Size Product
3.4
Wedge Tension Testing of Full-Size Product
3.5
Tension Testing of Machined Test Specimens
3.6
Total Extension at Fracture Test
Single Sheer Test
3.7
3.8
For Internally Threaded Fasteners:
4
Product Hardness
4.1
Proof Load Test
4.2
Cone Proof Load Test
4.3
For Washers and Direct Tension Indicators:
5
Product Hardness-General Requirements
5.1
Through Hardened Washers
5.2
Carburized Washers
5.3
Stainless Steel and Nonferrous Washers
5.4
Direct Tension Indicators
5.5
Compression Load
5.6
For Rivets:
6
Product Hardness
6.1
Test for Embrittlement of Metallic-Coated Externally Threaded Fasteners
7
Test Method for Determining Decarburization and Carburization
8
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
Note 1: The values are stated in inch-pound for inch fasteners and SI metric units for metric fasteners.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and h...
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F606/F606M − 14a
StandardTest Methods for
Determining the Mechanical Properties of Externally and
Internally Threaded Fasteners, Washers, Direct Tension
1
Indicators, and Rivets
This standard is issued under the fixed designation F606/F606M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
Product Hardness 6.1
Test for Embrittlement of Metallic-Coated Externally Threaded 7
1.1 These test methods cover establishment of procedures
Fasteners
for conducting tests to determine the mechanical properties of Test Method for Determining Decarburization and Carburization 8
externally and internally threaded fasteners, washers, direct
1.4 The values stated in either SI units or inch-pound units
tension indicators, and rivets.
are to be regarded separately as standard. The values stated in
each system may not be exact equivalents; therefore, each
1.2 Property requirements and the applicable tests for their
system shall be used independently of the other. Combining
determination are specified in individual product standards. In
values from the two systems may result in non-conformance
those instances where the testing requirements are unique or at
with the standard.
variance with these standard procedures, the product standard
shall specify the controlling testing requirements. In the
NOTE 1—The values are stated in inch-pound for inch fasteners and SI
absenceofanyspecifiedtestrequirement(s),thesetestmethods
metric units for metric fasteners.
shall apply.
1.5 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
1.3 These test methods describe mechanical tests for deter-
responsibility of the user of this standard to establish appro-
mining the following properties:
priate safety and health practices and determine the applica-
Section
For Externally Threaded Fasteners: 3 bility of regulatory limitations prior to use.
Product Hardness 3.1
Proof Load 3.2.1
2. Referenced Documents
Method 1, Length Measurement 3.2.3
2
Method 2, Yield Strength 3.2.4
2.1 ASTM Standards:
Method 3, Uniform Hardness 3.2.5
A394Specification for Steel Transmission Tower Bolts,
Axial Tension Testing of Full-Size Product 3.4
Zinc-Coated and Bare
Wedge Tension Testing of Full-Size Product 3.5
Tension Testing of Machined Test Specimens 3.6 E4Practices for Force Verification of Testing Machines
Total Extension at Fracture Test 3.7
E8/E8MTest Methods for Tension Testing of Metallic Ma-
Single Sheer Test 3.8
terials
For Internally Threaded Fasteners: 4
Product Hardness 4.1
E10Test Method for Brinell Hardness of Metallic Materials
Proof Load Test 4.2
E18Test Methods for Rockwell Hardness of Metallic Ma-
Cone Proof Load Test 4.3
terials
For Washers and Direct Tension Indicators: 5
Product Hardness-General Requirements 5.1
E83Practice for Verification and Classification of Exten-
Through Hardened Washers 5.2
someter Systems
Carburized Washers 5.3
E92TestMethodforVickersHardnessofMetallicMaterials
Stainless Steel and Nonferrous Washers 5.4
3
Direct Tension Indicators 5.5
(Withdrawn 2010)
Compression Load 5.6
E384Test Method for Knoop and Vickers Hardness of
For Rivets: 6
Materials
1 2
These test methods are under the jurisdiction of ASTM Committee F16 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Fasteners and are the direct responsibility of Subcommittee F16.01 on Test contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Methods. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Nov. 1, 2014. Published April 2015. Originally the ASTM website.
3
approved in 1979. Last previous edition approved in 2014 as F606–14. DOI: The last approved version of this historical standard is referenced on
10.1520/F0606_F0606M-14A. www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F606/F606M − 14a
F436Specification for Hardened Steel Washers 3.1.1.2 Forstuds,productswithoutparallelwrenchflatsand
F959Specification for Compressible-Washer-Type Direct for head styles other than hex and square; tests shall be
Tension Indicators for Use with Structural Fasteners conducted on the unthreaded shank, end of the bolt or stud or
F1624Test Method for Measurement of Hydrogen Em- at the arbitration location.
brittlement Th
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F606 − 14 F606/F606M − 14a
Standard Test Methods for
Determining the Mechanical Properties of Externally and
Internally Threaded Fasteners, Washers, Direct Tension
1
Indicators, and Rivets
This standard is issued under the fixed designation F606;F606/F606M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of
externally and internally threaded fasteners, washers, direct tension indicators, and rivets.
1.2 Property requirements and the applicable tests for their determination are specified in individual product standards. In those
instances where the testing requirements are unique or at variance with these standard procedures, the product standard shall
specify the controlling testing requirements. In the absence of any specified test requirement(s), these test methods shall apply.
1.3 These test methods describe mechanical tests for determining the following properties:
Section
For Externally Threaded Fasteners: 3
Product Hardness 3.1
Proof Load 3.2.1
Method 1, Length Measurement 3.2.3
Method 2, Yield Strength 3.2.4
Method 3, Uniform Hardness 3.2.5
Axial Tension Testing of Full-Size Product 3.4
Wedge Tension Testing of Full-Size Product 3.5
Tension Testing of Machined Test Specimens 3.6
Total Extension at Fracture Test 3.7
Single Sheer Test 3.8
For Internally Threaded Fasteners: 4
Product Hardness 4.1
Proof Load Test 4.2
Cone Proof Load Test 4.3
For Washers and Direct Tension Indicators: 5
Product Hardness-General Requirements 5.1
Through Hardened Washers 5.2
Carburized Washers 5.3
Stainless Steel and Nonferrous Washers 5.4
Direct Tension Indicators 5.5
Compression Load 5.6
For Rivets: 6
Product Hardness 6.1
Test for Embrittlement of Metallic-Coated Externally Threaded 7
Fasteners
Test Method for Determining Decarburization and Carburization 8
1.4 The values stated in either SI units or inch-pound units are to be regarded as standard. No other units of measurement are
included in this separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall
be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
NOTE 1—A complete metric companion to Test MethodsThe values are stated in inch-pound for F606 has been developed—inch fasteners and
SIF606M; therefore, no metric equivalents are shown in these test methods. metric units for metric fasteners.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1
These test methods are under the jurisdiction of ASTM Committee F16 on Fasteners and are the direct responsibility of Subcommittee F16.01 on Test Methods.
Current edition approved July 1, 2014Nov. 1, 2014. Published August 2014April 2015. Originally approved in 1979. Last previous edition approved in 20132014 as
F606 – 13.F606 – 14. DOI: 10.1520/F0606-14.10.1520/F0606_F0606M-14A.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F606/F606M − 14a
2. Referenced Documents
2
2.1 ASTM Standards:
A394 Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare
E4 Practices for Force Verification of Testing Machines
E8/E8M Test Methods for Tension Testing of Metallic Materials
E10 Test Method for Brinell Hardness of Metallic Materials
E18 Test Methods for Rockwell Hardness of Metallic Materials
E83 Practice for Verification and Classification of Extensometer Systems
3
E92 Test Method for Vickers Hardness of Metallic Materials (Withdrawn 2010)
E384 Test Method for Knoop and Vickers Hardness of Materials
F436 Specification for Hardened Steel Washers
F606M Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and
Rivets (Metric
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.