ASTM B535-06(2011)

Standard Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Seamless Pipe and Tube

ABSTRACT
This specification covers alloys UNS N08330 and N08332 in the form of hot-finished and cold-finished seamless pipe and tube intended for heat resisting applications and general corrosive service. The material shall be furnished in the annealed condition. The alloys shall conform to the composition limits of the material of this specification. Tensile strength, yield strength, elongation, and hardness of the material shall conform to the mechanical property requirements. Annealed alloy UNS N08332 shall conform to an average grain size set by this specification, or coarser. One test per lot is required. Flattening test shall also be performed. Each pipe or tube shall be subjected to either the hydrostatic test or to a nondestructive electric test.
SCOPE
1.1 This specification covers alloys UNS N08330 and N08332 in the form of hot-finished and cold-finished seamless pipe and tube intended for heat resisting applications and general corrosive service.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-May-2011
• ICS: 77.150.40 - Nickel and chromium products
• Technical Committee: B02 - Nonferrous Metals and Alloys
• Drafting Committee: B02.07 - Refined Nickel and Cobalt and Their Alloys

Relations

• Replaces: ASTM B535-06 - Standard Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Seamless Pipe and Tube
• Effective Date: 01-Jun-2011
• Referred By: ASTM B366/B366M-23 - Standard Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings
• Effective Date: 01-Jun-2011

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B535 −06(Reapproved 2011)
Standard Specification for
Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and
1
N08332) Seamless Pipe and Tube
This standard is issued under the fixed designation B535; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 4. General Requirement
2
4.1 Material furnished under this specification shall con-
1.1 This specification covers alloys UNS N08330 and
N08332 in the form of hot-finished and cold-finished seamless form to the applicable requirements of Specification B829
unless otherwise provided herein.
pipe and tube intended for heat resisting applications and
general corrosive service.
5. Ordering Information
1.2 The values stated in inch-pound units are to be regarded
5.1 It is the responsibility of the purchaser to specify all
as standard. The values given in parentheses are mathematical
requirements that are necessary for material ordered under this
conversions to SI units that are provided for information only
specification. Examples of such requirements include, but are
and are not considered standard.
not limited to, the following:
1.3 This standard does not purport to address all of the
5.1.1 Alloy name or UNS number,
safety concerns, if any, associated with its use. It is the
5.1.2 ASTM designation and year of issue,
responsibility of the user of this standard to become familiar
5.1.3 Dimensions:
with all hazards including those identified in the appropriate
5.1.3.1 Pipe—Specify standard pipe size and schedule,
Material Safety Data Sheet (MSDS) for this product/material
5.1.3.2 Tube—Specify outside diameter and nominal or
as provided by the manufacturer, to establish appropriate
minimum wall,
safety and health practices, and determine the applicability of
5.1.3.3 Length (specific or random),
regulatory limitations prior to use.
5.1.4 Finish:
5.1.4.1 Pipe—Specify cold-worked or hot-worked,
2. Referenced Documents
5.1.4.2 Tube—Specify cold-worked or hot-finished,
3
2.1 ASTM Standards:
5.1.5 Quantity (feet or meters or number of pieces),
B829 Specification for General Requirements for Nickel and 5.1.6 Hydrostatic Test or Nondestructive Electric Test—
Nickel Alloys Seamless Pipe and Tube
Specify type of test (see 8.4),
B899 Terminology Relating to Non-ferrous Metals and Al- 5.1.7 Certification—State if certification is required,
loys
5.1.8 Samples for Product (Check) Analysis—State whether
samples for product analysis should be furnished, and
3. Terminology 5.1.9 Purchaser Inspection—If purchaser wishes to witness
tests or inspection of material at place of manufacture, the
3.1 Definitions—Definitions for terms defined in Terminol-
purchase order must so state indicating which test or inspec-
ogy B899 shall apply unless otherwise defined by the require-
tions are to be witnessed.
ments of this document.
6. Materials and Manufacture
6.1 Heat Treatment—The material shall be furnished in the
1
This specification is under the jurisdiction of ASTM Committee B02 on
annealed condition. The final heat treatment of UNS N08330
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
shall be 1900°F (1040°C) minimum. The final heat treatment
B02.07 on Refined Nickel and Cobalt and Their Alloys.
Current edition approved June 1, 2011. Published June 2011. Originally
of UNS N08332 shall be 2100°F (1150°C) minimum.
approved in 1970. Last previous edition approved in 2006 as B535 – 06. DOI:
10.1520/B0535-06R11.
7. Chemical Composition
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi-
cation SB-535 in Section II of that Code.
7.1 The material shall conform to the composition limits
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
specified in Table 1.
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
7.1.1 A chemical analysis shall be made on each lot of
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. material as described in Specification B829.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B535−06(2011)
TABLE 1 Chemical Requirements
8.3 Flattening Test—One section of pipe or tube per lot, not
1
Element Composition Limits, % less than 2 ⁄2 in. (63.5 mm) in length, shall be flattened cold
A
C . between parallel plates in two steps. During the first step,
Mn 2.00 max
which is test for ductility, no cracks or breaks on the inside,
P 0.03 max
outside or
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B535–06 Designation: B535 – 06 (Reapproved 2011)
Standard Specification for
Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and
1
N08332) Seamless Pipe and Tube
This standard is issued under the fixed designation B535; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
2
1.1 This specification covers alloys UNS N08330 and N08332 in the form of hot-finished and cold-finished seamless pipe and
tube intended for heat resisting applications and general corrosive service.
1.2Thevaluesstatedininch-poundunitsaretobeconsideredasthestandard.Thevaluesgiveninparenthesesareforinformation
only.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
B829 Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube
B899 Terminology Relating to Non-ferrous Metals and Alloys
3. Terminology
3.1 Definitions:
3.1.1 Definitions for terms defined in Terminology B899 shall apply unless otherwise defined by the requirements of this
document.
4. General Requirement
4.1 Material furnished under this specification shall conform to the applicable requirements of Specification B829 unless
otherwise provided herein.
5. Ordering Information
5.1 It is the responsibility of the purchaser to specify all requirements that are necessary for material ordered under this
specification. Examples of such requirements include, but are not limited to, the following:
5.1.1 Alloy name or UNS number,
5.1.2 ASTM designation and year of issue,
5.1.3 Dimensions:
5.1.3.1 Pipe—Specify standard pipe size and schedule,
5.1.3.2 Tube—Specify outside diameter and nominal or minimum wall,
5.1.3.3 Length (specific or random),
5.1.4 Finish:
5.1.4.1 Pipe—Specify cold-worked or hot-worked,
5.1.4.2 Tube—Specify cold-worked or hot-finished,
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB02onNonferrousMetalsandAlloysandisthedirectresponsibilityofSubcommitteeB02.07onRefined
Nickel and Cobalt and Their Alloys.
Current edition approved Dec.June 1, 2006.2011. Published January 2007.June 2011. Originally approved in 1970. Last previous edition approved in 20042006 as
B535 – 046. DOI: 10.1520/B0535-06R11.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SB-535 in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
B535 – 06 (2011)
5.1.5 Quantity (feet or meters or number of pieces),
5.1.6 Hydrostatic Test or Nondestructive Electric Test—Specify type of test (see 8.4),
5.1.7 Certification—State if certification is required,
5.1.8 Samples for Product (Check) Analysis—State whether samples for product analysis should be furnished, and
5.1.9 Purchaser Inspection—If purchaser wishes to witness tests or inspection of material at place of manufacture, the purchase
order must so state indicating which test or inspections are to be witnessed.
6. Materials and Manufacture
6.1 Heat Treatment—The material shall be furnished in the annealed condition. The final heat treatment of UNS N08330 shall
be 1900°F (1040°C) minimum. The final heat treatment of UNS N08332 shall be 2100°F (1150°C) minimum.
7. Chemical Composition
7.1 The material shall conform to the composition limits specified in Table 1.
7.1.1 A chemical analysis shall be
...