ASTM B435-06

Standard Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Plate, Sheet, and Strip

ABSTRACT
This specification covers alloys UNS N06002, UNS N06230, UNS N12160, and UNS R30556 in the form of rolled plate, sheet, and strip for heat-resisting and general corrosive service. The material shall conform to the required chemical composition for nickel, iron, chromium, cobalt, molybdenum, tungsten, carbon, silicon, manganese, phosphorus, sulfur, columbium, tantalum, aluminum, zirconium, lanthanum, nitrogen, boron, and titanium. The alloy shall conform to specific mechanical requirements such as tensile strength, yield strength, and elongation. Annealed alloys UNS N06002, UNS N06230, and UNS R30556 sheet and strip shall conform to the grain size requirements.
SCOPE
1.1 This specification covers alloys UNS N06002, UNS N06230, UNS N12160, and UNS R30556* in the form of rolled plate, sheet, and strip for heat-resisting and general corrosive service.
1.2 The following products are covered under this specification:
1.2.1 Sheet and Strip Hot- or cold-rolled, annealed, and descaled unless solution annealing is performed in an atmosphere yielding a bright finish.
1.2.2 PlateHot-rolled, solution-annealed, and descaled.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-May-2006
• ICS: 77.140.50 - Flat steel products and semi-products
• Technical Committee: B02 - Nonferrous Metals and Alloys
• Drafting Committee: B02.07 - Refined Nickel and Cobalt and Their Alloys

Relations

• Replaces: ASTM B435-03 - Standard Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Plate, Sheet, and Strip
• Effective Date: 01-Jun-2006
• Replaced By: ASTM B435-06(2011) - Standard Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Plate, Sheet, and Strip
• Effective Date: 01-Jun-2011
• Referred By: ASTM B474/B474M-19 - Standard Specification for Electric Fusion Welded Nickel and Nickel Alloy Pipe
• Effective Date: 01-Jun-2006
• Referred By: ASTM B366/B366M-23 - Standard Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings
• Effective Date: 01-Jun-2006
• Referred By: ASTM B906-22 - Standard Specification for General Requirements for Flat-Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip
• Effective Date: 01-Jun-2006

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B435 – 06
Standard Specification for
UNS N06002, UNS N06230, UNS N12160, and UNS R30556
1
Plate, Sheet, and Strip
This standard is issued under the fixed designation B435; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope B906 Specification for General Requirements for Flat-
2 Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip
1.1 This specification covers alloys UNS N06002, UNS
E527 Practice for Numbering Metals and Alloys in the
N06230, UNS N12160, and UNS R30556* in the form of
Unified Numbering System (UNS)
rolled plate, sheet, and strip for heat-resisting and general
corrosive service.
3. Terminology
1.2 The following products are covered under this specifi-
3.1 Definitions of Terms Specific to This Standard:
cation:
3
3.1.1 plate, n—material ⁄16 in. (4.76 mm) and over in
1.2.1 Sheet and Strip—Hot- or cold-rolled, annealed, and
thickness.
descaled unless solution annealing is performed in an atmo-
3
3.1.2 sheet and strip, n—materialunder ⁄16in.(4.76mm)in
sphere yielding a bright finish.
thickness.
1.2.2 Plate—Hot-rolled, solution-annealed, and descaled.
1.3 The values stated in inch-pound units are to be regarded
4. General Requirements
as the standard. The values given in parentheses are for
4.1 Material furnished under this specification shall con-
information only.
form to the applicable requirements of Specification B906
1.4 This standard does not purport to address all of the
unless otherwise provided herein.
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to become familiar
5. Ordering Information
with all hazards including those identified in the appropriate
5.1 It is the responsibility of the purchaser to specify all
Material Safety Data Sheet (MSDS) for this product/material
requirements that are necessary for material ordered under this
as provided by the manufacturer, to establish appropriate
specification. Examples of such requirements include, but are
safety and health practices, and determine the applicability of
not limited to the following:
regulatory limitations prior to use.
5.1.1 Alloy,
5.1.2 Dimensions—Thickness (in decimals of an inch),
2. Referenced Documents
3 width, and length (inch or fraction of an inch),
2.1 ASTM Standards:
5.1.3 Certification—State if certification or a report of test
resultsisrequired(SpecificationB906,sectiononMaterialTest
1
This specification is under the jurisdiction of ASTM Committee B02 on
Report an Certification),
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
5.1.4 Optional Requirement—Plate; state how plate is to be
B02.07 on Refined Nickel and Cobalt and Their Alloys.
cut (Specification B906, Table titled Permissible Variations in
Current edition approved June 1, 2006. Published June 2006. Originally
approved in 1966. Last previous edition approved in 2003 as B435 - 03. DOI: width and Length of Sheared, Torch-Cut, or Abrasive-Cut
10.1520/B0435-06.
Rectangular Plate),
2
For ASME Boiler and Pressure Vessel Code applications, see related Specifi-
5.1.5 Purchase Inspection—State which tests or inspections
cation SB-435 in Section II of that Code.
aretobewitnessed(SpecificationB906,sectiononInspection),
* NewdesignationestablishedinaccordancewithPracticeE527andSAEJ1086,
Practice for Numbering Metals and Alloys (UNS).
and
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
5.1.6 Samples for Product (Check) Analysis—State whether
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
samples should be furnished (Specification B906, section on
Standards volume information, refer to the standard’s Document Summary page on
Sampling).
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
B435 – 06
TABLE 1 Chemical Requirements
Composition Limits, %
Element
UNS N06002 UNS N06230 UNS R30556 UNS N12160
Nickel remainder remainder 19.0–22.5 remainder
Iron 17.0–20.0 3.0 max remainder 3.5 max
Chromium 20.5–23.0 20.0–24.0 21.0–23.0 26.0–30.0
Cobalt 0.5–2.5 5.0 max 16.0–21.0 27.0–33.0
Molybdenum 8.0–10.0 1.0–3.00 2.5–4.0 1.0 max
Tungsten 0.2–1.0 13.0–15.0 2.0–3.5 1.0 max
Carbon 0.05–0.15 0.05–0.15 0.05–0.15 0.15 max
Silicon 1.00 max 0.25–0.75 0.20–0.80 2.4–3.0
Manganese 1.00 max 0.30–1.00 0.50–2.00 1.5 max
Phosphorus 0.04 max 0.030 max 0.04 max 0.030 max
Sulfur 0.03 max 0.015 max 0.015 max 0.015 max
Columbium (N6) . . 0.30 max 1.0 max
Tantalum . . 0.30–1.25 .
Aluminum . 0.50 max
...