ASTM B435-06(2011)
(Specification)Standard Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Plate, Sheet, and Strip
Standard Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Plate, Sheet, and Strip
ABSTRACT
This specification covers alloys UNS N06002, UNS N06230, UNS N12160, and UNS R30556 in the form of rolled plate, sheet, and strip for heat-resisting and general corrosive service. The material shall conform to the required chemical composition for nickel, iron, chromium, cobalt, molybdenum, tungsten, carbon, silicon, manganese, phosphorus, sulfur, columbium, tantalum, aluminum, zirconium, lanthanum, nitrogen, boron, and titanium. The alloy shall conform to specific mechanical requirements such as tensile strength, yield strength, and elongation. Annealed alloys UNS N06002, UNS N06230, and UNS R30556 sheet and strip shall conform to the grain size requirements.
SCOPE
1.1 This specification covers alloys UNS N06002, UNS N06230, UNS N12160, and UNS R30556* in the form of rolled plate, sheet, and strip for heat-resisting and general corrosive service.
1.2 The following products are covered under this specification:
1.2.1 Sheet and Strip—Hot- or cold-rolled, annealed, and descaled unless solution annealing is performed in an atmosphere yielding a bright finish.
1.2.2 Plate—Hot-rolled, solution-annealed, and descaled.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B435 −06(Reapproved2011)
Standard Specification for
UNS N06002, UNS N06230, UNS N12160, and UNS R30556
Plate, Sheet, and Strip
This standard is issued under the fixed designation B435; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope E527 Practice for Numbering Metals and Alloys in the
2 Unified Numbering System (UNS)
1.1 This specification covers alloys UNS N06002, UNS
N06230, UNS N12160, and UNS R30556* in the form of
3. Terminology
rolled plate, sheet, and strip for heat-resisting and general
corrosive service. 3.1 Definitions of Terms Specific to This Standard:
3.1.1 plate, n—material ⁄16 in. (4.76 mm) and over in
1.2 The following products are covered under this specifi-
thickness.
cation:
1.2.1 Sheet and Strip—Hot- or cold-rolled, annealed, and
3.1.2 sheet and strip, n—material under ⁄16 in. (4.76 mm) in
descaled unless solution annealing is performed in an atmo-
thickness.
sphere yielding a bright finish.
1.2.2 Plate—Hot-rolled, solution-annealed, and descaled.
4. General Requirements
1.3 The values stated in inch-pound units are to be regarded
4.1 Material furnished under this specification shall con-
as standard. The values given in parentheses are mathematical
form to the applicable requirements of Specification B906
conversions to SI units that are provided for information only
unless otherwise provided herein.
and are not considered standard.
1.4 This standard does not purport to address all of the
5. Ordering Information
safety concerns, if any, associated with its use. It is the
5.1 It is the responsibility of the purchaser to specify all
responsibility of the user of this standard to become familiar
requirements that are necessary for material ordered under this
with all hazards including those identified in the appropriate
specification. Examples of such requirements include, but are
Material Safety Data Sheet (MSDS) for this product/material
not limited to the following:
as provided by the manufacturer, to establish appropriate
5.1.1 Alloy,
safety and health practices, and determine the applicability of
5.1.2 Dimensions—Thickness (in decimals of an inch),
regulatory limitations prior to use.
width, and length (inch or fraction of an inch),
5.1.3 Certification—State if certification or a report of test
2. Referenced Documents
resultsisrequired(SpecificationB906,sectiononMaterialTest
2.1 ASTM Standards:
Report an Certification),
B906 Specification for General Requirements for Flat-
5.1.4 Optional Requirement—Plate; state how plate is to be
Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip
cut (Specification B906, Table titled Permissible Variations in
width and Length of Sheared, Torch-Cut, or Abrasive-Cut
Rectangular Plate),
This specification is under the jurisdiction of ASTM Committee B02 on
5.1.5 Purchase Inspection—State which tests or inspections
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
B02.07 on Refined Nickel and Cobalt and Their Alloys.
aretobewitnessed(SpecificationB906,sectiononInspection),
Current edition approved June 1, 2011. Published June 2011. Originally
and
approved in 1966. Last previous edition approved in 2006 as B435 - 06. DOI:
5.1.6 Samples for Product (Check) Analysis—State whether
10.1520/B0435-06R11.
For ASME Boiler and Pressure Vessel Code applications, see related Specifi- samples should be furnished (Specification B906, section on
cation SB-435 in Section II of that Code.
Sampling).
* NewdesignationestablishedinaccordancewithPracticeE527andSAEJ1086,
Practice for Numbering Metals and Alloys (UNS).
6. Chemical Composition
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
6.1 The material shall conform to the requirements as to
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. chemical composition prescribed in Table 1.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
B435−06(2011)
TABLE 1 Chemical Requirements
Composition Limits, %
Element
UNS N06002 UNS N06230 UNS R30556 UNS N12160
Nickel remainder remainder 19.0–22.5 remainder
Iron 17.0–20.0 3.0 max remainder 3.5 max
Chromium 20.5–23.0 20.0–24.0 21.0–23.0 26.0–30.0
Cobalt 0.5–2.5 5.0 max 16.0–21.0 27.0–33.0
Molybdenum 8.0–10.0 1.0–3.00 2.5–4.0 1.0 max
Tungsten 0.2–1.0 13.0–15.0 2.0–3.5 1.0 max
Carbon 0.05–0.15 0.05–0.15 0.05–0.15 0.15 max
Silicon 1.00 max 0.25–0.75 0.20–0.80 2.4–3.0
Manganese 1.00 max 0.30–1.00 0.50–2.00 1.5 max
Phosphorus 0.04 max 0.030 max 0.04 max 0.030 max
Sulfur 0.03 max 0.015 max 0.015 max 0.015 max
Columbium (N6) . . 0.30 max 1.0 max
Tantalum . . 0.30–1.25 .
Aluminum . 0.50 max 0.10–0.50 .
Zirconium . . 0.001–0.10 .
Lanthanum . 0.005–0.050 0.005–0.10 .
Ni
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.