ASTM D7611/D7611M-13e1
(Practice)Standard Practice for Coding Plastic Manufactured Articles for Resin Identification
Standard Practice for Coding Plastic Manufactured Articles for Resin Identification
SIGNIFICANCE AND USE
4.1 Resin Identification Codes are used solely to identify the plastic resin used in a manufactured article.
4.2 Resin Identification Codes are not “recycle codes.” The use of a Resin Identification Code on a manufactured plastic article does not imply that the article is recycled or that there are systems in place to effectively process the article for reclamation or re-use. The term “recyclable” or other environmental claims shall not be placed in proximity to the Code.
4.3 This practice is based upon the system developed in 1988 by the Society of the Plastics Industry, Inc (SPI). It is possible that some states or countries will have incorporated the original SPI practice into statute or regulation. In those situations, that statute or regulation takes precedence over this standard.
4.4 This practice shall only apply to new tooling. Existing molds that already incorporate older versions of the SPI RIC may be modified, but modification is not required.
SCOPE
1.1 This practice stipulates the types, names, and sizes of Codes for those material types specified in Table 1.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are likely not to be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems is likely to result in non-conformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1: There is no known ISO equivalent to this standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation:D7611/D7611M −13
Standard Practice for
Coding Plastic Manufactured Articles for Resin
1
Identification
This standard is issued under the fixed designation D7611/D7611M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Editorially corrected adjunct information in September 2014.
1. Scope 4.2 Resin Identification Codes are not “recycle codes.” The
use of a Resin Identification Code on a manufactured plastic
1.1 This practice stipulates the types, names, and sizes of
article does not imply that the article is recycled or that there
Codes for those material types specified in Table 1.
are systems in place to effectively process the article for
1.2 The values stated in either SI units or inch-pound units
reclamation or re-use. The term “recyclable” or other environ-
are to be regarded separately as standard. The values stated in
mental claims shall not be placed in proximity to the Code.
each system are likely not to be exact equivalents; therefore,
4.3 This practice is based upon the system developed in
each system shall be used independently of the other. Combin-
1988 by the Society of the Plastics Industry, Inc (SPI). It is
ing values from the two systems is likely to result in non-
possible that some states or countries will have incorporated
conformance with the standard.
the original SPI practice into statute or regulation. In those
1.3 This standard does not purport to address all of the
situations, that statute or regulation takes precedence over this
safety concerns, if any, associated with its use. It is the
standard.
responsibility of the user of this standard to establish appro-
4.4 This practice shall only apply to new tooling. Existing
priate safety and health practices and determine the applica-
molds that already incorporate older versions of the SPI RIC
bility of regulatory limitations prior to use.
may be modified, but modification is not required.
NOTE 1—There is no known ISO equivalent to this standard.
5. Requirements
2. Referenced Documents
5.1 The Code is to be molded, formed or imprinted on the
manufactured article.
2.1 ASTM Adjuncts:
Adjunct to D7611/D7611M Standard Practice for Coding
5.2 The Code shall be clear and legible.
2
Plastic Manufactured Articles for Resin Identification
5.3 The size of the Code shall normally equal or exceed 12
1
mm [ ⁄2 in.] in height and width.
3. Terminology
NOTE 2—For small parts or components, it is not always possible to
3.1 Definitions:
conform to these size requirements. In these cases, it is important to
3.1.1 Resin Identification Code (RIC Code)—a molded,
maximize the size and legibility of the Code.
imprinted or raised symbol or wording that consists of an
5.4 The Code shall be placed in an inconspicuous location
equilateral triangle, a Resin Identification Number, and an
on the manufactured article, such as the bottom or the back,
Abbreviated Term for polymeric material in compliance with
where it will not be obvious to the consumer at the point of
Fig. 1 and Table 1.
purchase so it does not influence the consumer’s buying
decision.
4. Significance and Use
5.5 The Code shall be as shown in Table 1. Option A is
4.1 Resin Identification Codes are used solely to identify the
commonly found in North America. Option B is often found
plastic resin used in a manufactured article.
internationally. Either option is acceptable.
5.6 The numbering system within the equilateral triangle
1
This practice is under the jurisdiction ofASTM Committee D20 on Plastics and
shall correspond to the generic class of resins shown in Table
is the direct responsibility of Subcommittee D20.95 on Recycled Plastics.
1.
Current edition approved June 1, 2013. Published June 2013. Originally
approved in 2010. Last previous edition approved in 2010 as D7611/D7611M - 10.
5.7 The Code with the Resin Identification Number “1” and
DOI:10.1520/D7611_D7611M-13.
2
the Abbreviated Term “PETE” is reserved for manufactured
Available from ASTM International Headquarters. Order Adjunct No.
ADJD761114-EA. Original adjunct produced in 2010.Adjunct last revised in 2014. articles produced from Poly(ethylene terephthalate).
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´1
D7611/D7611M−13
TABLE 1 Resin Identification Codes
5.7.1 The Code with the Resin Identification Number “1” also contain at least one additional layer of a different material.
and the Abbreviated Term “PETE+” is reserved for manufac- ThisCodedoesnotrequirethemodificationofexistingtooling.
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: D7611/D7611M − 13 D7611/D7611M − 13
Standard Practice for
Coding Plastic Manufactured Articles for Resin
1
Identification
This standard is issued under the fixed designation D7611/D7611M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Editorially corrected adjunct information in September 2014.
1. Scope
1.1 This practice stipulates the types, names, and sizes of Codes for those material types specified in Table 1.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system are likely not to be exact equivalents; therefore, each system shall be used independently of the other. Combining values
from the two systems is likely to result in non-conformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
NOTE 1—There is no known ISO equivalent to this standard.
2. Referenced Documents
2.1 ASTM Adjuncts:
2
Adjunct to D7611/D7611M Standard Practice for Coding Plastic Manufactured Articles for Resin Identification
3. Terminology
3.1 Definitions:
3.1.1 Resin Identification Code (RIC;(RIC Code)—a molded, imprinted or raised symbol or wording that consists of an
equilateral triangle, a Resin Identification Number, and an Abbreviated Term for polymeric material in compliance with Fig. 1 and
Table 1.
4. Significance and Use
4.1 Resin Identification Codes are used solely to identify the plastic resin used in a manufactured article.
4.2 Resin Identification Codes are not “recycle codes.” The use of a Resin Identification Code on a manufactured plastic article
does not imply that the article is recycled or that there are systems in place to effectively process the article for reclamation or
re-use. The term “recyclable” or other environmental claims shall not be placed in proximity to the Code.
4.3 This practice is based upon the system developed in 1988 by the Society of the Plastics Industry, Inc (SPI). It is possible
that some states or countries will have incorporated the original SPI practice into statute or regulation. In those situations, that
statute or regulation takes precedence over this standard.
4.4 This practice shall only apply to new tooling. Existing molds that already incorporate older versions of the SPI RIC may
be modified, but modification is not required.
5. Requirements
5.1 The Code is to be molded, formed or imprinted on the manufactured article.
5.2 The Code shall be clear and legible.
1
This practice is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.95 on Recycled Plastics.
Current edition approved June 1, 2013. Published June 2013. Originally approved in 2010. Last previous edition approved in 2010 as D7611/D7611M - 10.
DOI:10.1520/D7611_D7611M-13.
2
Available from ASTM International Headquarters. Order Adjunct No. ADJD7611A-E-PDFADJD761114-EA. Original adjunct produced in 2010. Adjunct last revised in
2013.2014.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´1
D7611/D7611M − 13
TABLE 1 Resin Identification Codes
1
5.3 The size of the Code shall normally equal or exceed 12 mm [ ⁄2 in.] in height and width.
NOTE 2—For small parts or components, it is not always possible to conform to these size requirements. In these cases, it is important to maximize
the size and legibility of the Code.
2
---------------------- Page: 2 ----------------------
´1
D7611/D7611M − 13
FIG. 1 Example of a Resin Identification Marker
5.4 The Code shall be placed in an inconspicuous location on the manufactured article, such as the bottom or the back, where
it will not be obvious to the consumer at the point of purchase so it does not influence the consumer’s buying decision.
5.5 The Code shall be as shown in Table 1. Option A is commonly found in North America. Option B is often found
internationally. Either option is acceptable.
5.6 The numbering system within the equilateral triangle shall correspond to th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.