ASTM C1281-16

Standard Specification for Preformed Tape Sealants for Glazing Applications

ABSTRACT
This specification describes preformed tape sealants for use in glazing applications. These materials are generally used to serve as components of glazing systems. They are intended to serve as a water and air barrier. The preformed tape sealant shall be composed of appropriate raw materials conformed to the requirements specified. The preformed tape sealant shall be of uniform dimensions and consistency. When properly applied, this material shall form a seal to prevent air and water from entering the system. Different test methods shall be performed in order to determine the following properties: low temperature flexibility, weight loss, vehicle migration, backing removal, yield strength, compression or recovery, water absorption, and flow.
SIGNIFICANCE AND USE
6.1 This specification describes only preformed tape sealants for glazing applications. Their use is specific under glazing systems to serve as a water and air barrier. The test methods chosen are to determine their efficiency in this use. This specification does not describe all required properties of the preformed tape sealants. It should be recognized by the purchaser and design professional that not all preformed tape sealants meeting this specification are suitable for all applications. In some instances, additional requirements will be agreed to by the supplier and user.
SCOPE
1.1 This specification describes preformed tape sealants for use in glazing applications. These materials are generally used to serve as components of glazing systems. They are intended to serve as a water and air barrier.  
1.2 This specification is not intended for preformed foam tape sealants.  
1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are provided for information purposes only.  
1.4 The subcommittee with jurisdiction is not aware of any similar ISO standard.  
1.5 The following precautionary statement pertains only to the test method section of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-May-2016
• ICS: 91.100.50 - Binders. Sealing materials
• Technical Committee: C24 - Building Seals and Sealants
• Drafting Committee: C24.10 - Specifications, Guides and Practices

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1281 −16
Standard Specification for
1
Preformed Tape Sealants for Glazing Applications
This standard is issued under the fixed designation C1281; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope C972 Test Method for Compression-Recovery of Tape Seal-
ant
1.1 This specification describes preformed tape sealants for
C1016 Test Method for Determination of Water Absorption
use in glazing applications. These materials are generally used
of Sealant Backing (Joint Filler) Material
to serve as components of glazing systems. They are intended
C1266 Test Method for Flow Characteristics of Preformed
to serve as a water and air barrier.
Tape Sealants
1.2 This specification is not intended for preformed foam
3. Terminology
tape sealants.
3.1 Definitions—Thedefinitionsofthefollowingtermsused
1.3 The values stated in SI units are to be regarded as the
in this specification are found in Terminology C717: compres-
standard. The values in parentheses are provided for informa-
sion seal, glazing, standard conditions, tape sealant.
tion purposes only.
1.4 The subcommittee with jurisdiction is not aware of any 4. Materials and Manufacturers
similar ISO standard.
4.1 The preformed tape sealant shall be composed of
1.5 The following precautionary statement pertains only to
appropriate raw materials to result in conformance to this
the test method section of this specification. This standard does
specification.
not purport to address all of the safety concerns, if any,
4.2 The preformed tape sealant shall be of uniform dimen-
associated with its use. It is the responsibility of the user of this
sions and consistency.
standard to establish appropriate safety and health practices
4.3 When properly applied, this material shall form a seal to
and determine the applicability of regulatory limitations prior
prevent air and water from entering the system.
to use.
5. Requirements
2. Referenced Documents
5.1 The shelf-life of this sealant shall be determined by its
2
2.1 ASTM Standards:
manufacturer. When establishing the shelf-life, the manufac-
C717 Terminology of Building Seals and Sealants
turer should also identify acceptable conditions of storage for
C765 Test Method for Low-Temperature Flexibility of Pre-
the sealant.
formed Tape Sealants
5.2 Physical Properties—The physical properties of the
C771 Test Method for Weight Loss After Heat Aging of
material shall conform to the requirements specified in Table 1.
Preformed Tape Sealants
C772 Test Method for Oil Migration or Plasticizer Bleed-
6. Significance and Use
Out of Preformed Tape Sealants
6.1 This specification describes only preformed tape seal-
C879 Test Methods for Release Papers Used with Preformed
ants for glazing applications. Their use is specific under
Tape Sealants
glazing systems to serve as a water and air barrier. The test
C908 Test Method for Yield Strength of Preformed Tape
methods chosen are to determine their efficiency in this use.
Sealants
This specification does not describe all required properties of
the preformed tape sealants. It should be recognized by the
1
This specification is under the jurisdiction of ASTM Committee C24 on
purchaser and design professional that not all preformed tape
Building Seals and Sealants and is the direct responsibility of Subcommittee C24.10
sealants meeting this specification are suitable for all applica-
on Specifications, Guides and Practices.
tions.Insomeinstances,additionalrequirementswillbeagreed
CurrenteditionapprovedJune1,2016.PublishedJuly2016.Originallyapproved
in 1994. Last previous edition approved in 2014 as C1281 – 14. DOI: 10.1520/
to by the supplier and user.
C1281-16.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or 7. Sampling
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
7.1 The preformed tape sealant to be tested for conformance
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. with the requirements of this specification shall be taken
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1281−16
TABLE 1 Material Requirements
8.5 Backing Removal—Test Method C879.
Properties ASTM Test Method Requirements
8.6 Yield Strength—Test Method C908.
Low Temp Flex C765 No Cracks at − 23°C (−10°F)
8.7 Compression/Recovery—Test Method C972.
No Adhesion Loss
Weight Loss C771 2 % Maximum
8.8 Water Absorption—Test Method C1016, Procedure A,
Vehicle Migration C772 1 paper stained maximum and t
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1281 − 14 C1281 − 16
Standard Specification for
1
Preformed Tape Sealants for Glazing Applications
This standard is issued under the fixed designation C1281; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification describes preformed tape sealants for use in glazing applications. These materials are generally used to
serve as components of glazing systems. They are intended to serve as a water and air barrier.
1.2 This specification is not intended for preformed foam tape sealants.
1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are provided for information
purposes only.
1.4 The subcommittee with jurisdiction is not aware of any similar ISO standard.
1.5 The following precautionary statement pertains only to the test method section of this specification.This standard does not
purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to
establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C717 Terminology of Building Seals and Sealants
C765 Test Method for Low-Temperature Flexibility of Preformed Tape Sealants
C771 Test Method for Weight Loss After Heat Aging of Preformed Tape Sealants
C772 Test Method for Oil Migration or Plasticizer Bleed-Out of Preformed Tape Sealants
C879 Test Methods for Release Papers Used with Preformed Tape Sealants
C908 Test Method for Yield Strength of Preformed Tape Sealants
C972 Test Method for Compression-Recovery of Tape Sealant
C1016 Test Method for Determination of Water Absorption of Sealant Backing (Joint Filler) Material
C1266 Test Method for Flow Characteristics of Preformed Tape Sealants
3. Terminology
3.1 Definitions—The definitions of the following terms used in this specification are found in Terminology C717: compression
seal, glazing, standard conditions, tape sealant.
4. Materials and Manufacturers
4.1 The preformed tape sealant shall be composed of appropriate raw materials to result in conformance to this specification.
4.2 The preformed tape sealant shall be of uniform dimensions and consistency.
4.3 When properly applied, this material shall form a seal to prevent air and water from entering the system.
5. Requirements
5.1 The tape sealant in the original unopened container shall meet the requirements of this specification and remain suitable for
use for a minimum of 12 months from the date of manufacture when stored at a temperature of 26.6°C (80°F) maximum.shelf-life
1
This specification is under the jurisdiction of ASTM Committee C24 on Building Seals and Sealants and is the direct responsibility of Subcommittee C24.10 on
Specifications, Guides and Practices.
Current edition approved June 1, 2014June 1, 2016. Published July 2014July 2016. Originally approved in 1994. Last previous edition approved in 20092014 as
C1281 – 03C1281(2009). – 14. DOI: 10.1520/C1281-14.10.1520/C1281-16.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1281 − 16
of this sealant shall be determined by its manufacturer. When establishing the shelf-life, the manufacturer should also identify
acceptable conditions of storage for the sealant.
5.2 Physical Properties—The physical properties of the material shall conform to the requirements specified in Table 1.
6. Significance and Use
6.1 This specification describes only preformed tape sealants for glazing applications. Their use is specific under glazing
systems to serve as a water and air barrier. The test methods chosen are to determine their efficiency in this use. This specification
does not describe all required properties of the preformed tape sealants. It should be recognized by the purchaser and design
professional that not all preformed tape sealants meeting this specification are suitable for all applications. In some ins
...