ASTM A1025-05(2010)
(Specification)Standard Specification for Ferroalloys, General Requirements
Standard Specification for Ferroalloys, General Requirements
ABSTRACT
This specification covers a group of common requirements that, unless otherwise specified in an individual specification, shall apply to ferroalloys and other alloying materials. The chemical analysis method shall be agreed upon by the purchaser and supplier. Unless otherwise specified, the material shall be sampled for determination of chemical composition and size.
SCOPE
1.1 This specification covers a group of common requirements that, unless otherwise specified in an individual specification, shall apply to ferroalloys and other alloying materials under each of the following ASTM specifications:
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A1025 – 05 (Reapproved 2010)
Standard Specification for
Ferroalloys and Other Alloying Materials, General
Requirements
This standard is issued under the fixed designation A1025; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
1.1 This specification covers a group of common require- 2.1 ASTM Standards:
ments that, unless otherwise specified in an individual speci- A99 Specification for Ferromanganese
fication, shall apply to ferroalloys and other alloying materials A100 Specification for Ferrosilicon
under each of the following ASTM specifications: A101 Specification for Ferrochromium
A102 Specification for Ferrovanadium
Title of Specification ASTM Designation
Ferromanganese A99
A132 Specification for Ferromolybdenum
Ferrosilicon A100
A146 Specification for Molybdenum Oxide Products
Ferrochromium A101
A323 Specification for Ferroboron
Ferrovanadium A102
Ferromolybdenum A132
A324 Specification for Ferrotitanium
Molybdenum Oxide Products A146
A481 Specification for Chromium Metal
Ferroboron A323
A482 Specification for Ferrochrome-Silicon
Ferrotitanium A324
Chromium Metal A481
A483 Specification for Silicomanganese
Ferrochrome-Silicon A482
A495 Specification for Calcium-Silicon Alloys
Silicomanganese A483
Calcium-Silicon Alloys A495 A550 Specification for Ferrocolumbium
Ferrocolumbium A550
A601 Specification for Electrolytic Manganese Metal
Electrolytic Manganese Metal A601
A610 Test Methods for Sampling and Testing Ferroalloys
Nickel Oxide Sinter A636
Ferromanganese Silicon A701 for Determination of Size
Titanium Scrap for Use in Deoxidation and Alloying of Steel A845
A636 Specification for Nickel Oxide Sinter
Aluminum Scrap for Use in Deoxidation and Alloying of Steel A846
A701 Specification for Ferromanganese-Silicon
Silicon Metal A922
A845 Specification for Titanium Scrap for Use in Deoxida-
1.2 This specification also covers a group of supplementary 3
tion and Alloying of Steel
requirements which may be applied to the above specifications
A846 Specification for Aluminum Scrap for Use in Deoxi-
as indicated therein. These are provided for use when addi- 3
dation and Alloying of Steel
tional testing or inspection is desired and apply only when
A922 Specification for Silicon Metal
specified individually by the purchaser in the order.
E29 Practice for Using Significant Digits in Test Data to
1.3 In case of conflict between the requirements of the
Determine Conformance with Specifications
individual specification and this general specification, the
E32 Practices for Sampling Ferroalloys and SteelAdditives
former shall prevail.
for Determination of Chemical Composition
1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
3. Ordering Information
responsibility of the user of this standard to establish appro-
3.1 Orders for material should include the following as
priate safety and health practices and determine the applica-
required, to describe the material adequately:
bility of regulatory requirements prior to use.
1 2
This specification is under the jurisdiction of ASTM Committee A01 on Steel, For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
A01.18 on Castings. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved April 1, 2010. Published May 2010. Originally the ASTM website.
approved in 2002. Last previous edition approved in 2005 as A1025 - 05. DOI: Withdrawn. The last approved version of this historical standard is referenced
10.1520/A1025-05R10. on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
A1025 – 05 (2010)
3.1.1 ASTM designation and year of issue, 6. Inspection
3.1.2 Grade of material,
6.1 The manufacturer shall afford the inspector representing
3.1.3 Size of material,
thepurchaserallreasonablefacilities,withoutcharge,tosatisfy
3.1.4 Quantity,
the purchaser that the material is being furnished in accordance
3.1.5 Packaging requirements, and
with the material specification.
3.1.6 Supplementary requirements desired, including the
7. Rejection
standards of acceptance.
7.1 Any rejections based on tests made in accordance with
4. Chemical Analysis the material specification shall be reported to the manufacturer
within 45 days from receipt of material by the purchaser.
4.1 The chemical analysis method shall be agreed upon by
the purchaser and supplier.
8. Certification
4.2 The manufacturer shall furnish a certificate referencing
8.1 The manufacturer’s certification shall be furnished to
the chemical analysis and appropriate supplementary require-
the purchaser at the time of shipment stating that the material
ments in the material specification.
was manufactured, sampled, tested, and inspected in accor-
4.3 For purposes of determining conformance with this
dancewiththematerialspecificationandwasfoundtomeetthe
specification, the reported analysis shall be rounded to the
requirements.
nearest unit in the last right-hand place of figures, used in
expressing the limiting value, in accordance with the rounding
9. Packaging and Package Marking
method of Practice E29.
9.1 Each lot/shipment shall be identified with appropriate
identification showing the material, theASTM designation, the
5. Sampling
size, the lot number, and name brand or trademark.
5.1 Unless otherwise specified, the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.