ASTM F2444-04

Standard Practice for Damage Prevention of Bearings, and Bearing Components Through Proper Handling Techniques

SCOPE
1.1 This practice covers requirements for the handling of all bearings and bearing components.
1.2 This is a general practice. The individual bearing handling requirements shall be as specified herein or as specified in the contract or purchase order. In the event of any conflict between requirements of this practice and the individual bearing requirements of an OEM drawing, procurement specification, or other specification, the latter shall govern. Many companies, organizations, and bearing users have excellent facilities, equipment, and knowledgeable personnel for handling bearings. The thrust of this practice is for users that do not have this knowledge of bearings.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-Oct-2004
• ICS: 21.100.01 - Bearings in general
• Technical Committee: F34 - Rolling Element Bearings
• Drafting Committee: F34.03 - Preservation, Cleaning and Packaging

Relations

• Replaced By: ASTM F2444-04(2012) - Standard Practice for Damage Prevention of Bearings, and Bearing Components Through Proper Handling Techniques
• Effective Date: 01-Dec-2012

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F2444 − 04
StandardPractice for
Damage Prevention of Bearings, and Bearing Components
1
Through Proper Handling Techniques
This standard is issued under the fixed designation F2444; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Terminology
3.1 Definitions—For definitions of terms used in this
1.1 This practice covers requirements for the handling of all
practice, refer to ABMA 1.
bearings and bearing components.
1.2 This is a general practice. The individual bearing han-
4. Significance and Use
dling requirements shall be as specified herein or as specified
4.1 This practice covers bearings and bearing components
in the contract or purchase order. In the event of any conflict
of all material compositions and grades. It may be used to
between requirements of this practice and the individual
develop a process for adequately handling bearings.
bearing requirements of an OEM drawing, procurement
specification, or other specification, the latter shall govern.
4.2 Unless the proper conditions of an adequate facility,
Many companies, organizations, and bearing users have excel-
equipment,andtrainedpersonnelareavailable,itmaybebetter
lent facilities, equipment, and knowledgeable personnel for
not to inspect the bearings in-house. The danger of contami-
handlingbearings.Thethrustofthispracticeisforusersthatdo
nating and damaging the bearings may be much greater than
not have this knowledge of bearings.
the possibility of receiving bearings that will not function.
1.3 This standard does not purport to address all of the
4.3 Bearings are easily damaged at the customers’ receiving
safety concerns, if any, associated with its use. It is the
and test areas. In most cases, bearings should be accepted
responsibility of the user of this standard to establish appro-
based on the bearing manufacturer’s certification. Certificates
priate safety and health practices and determine the applica-
of quality (conformance) supplied by the bearing manufacturer
bility of regulatory limitations prior to use.
may be furnished in lieu of actual performance of such testing
by the receiving activity of the bearings. The certificate shall
2. Referenced Documents
include the name of the purchaser, contract number/PO
number, name of the manufacturer or supplier, item
2
2.1 ABMA Standard:
identification, name of the material, lot number, lot size,
ABMA 1 Terminology
sample size, date of testing, test method, individual test results,
3
2.2 ISO Standards: and the specification requirements.
ISO 14644-1 Cleanrooms and Associated Controlled
4.4 This practice does not cover clean room requirements of
Environments—Part 1: Classification of Air Cleanliness
miniature and instrument precision bearings. These bearings
(DOD Adopted)
require clean room environments in accordance with ISO
ISO 14644-2 Cleanrooms and Associated Controlled
14644-1 and ISO 14644-2.
Environments—Part 2: Specifications for Testing and
Monitoring to Prove Continued Compliance with ISO
5. Reasons for Not Handling Bearings
14644-1
5.1 When bearings are received, the following questions
ISO 9001 Quality Management Systems—Requirements
must be asked:
5.1.1 What amount of inspection checks will be performed
on the bearings? Do we need to do any checks?
1
This practice is under the jurisdiction of ASTM Committee F34 on Rolling
5.1.2 What will it cost to establish and maintain equipment
Element Bearings and is the direct responsibility of Subcommittee F34.03 on
and facilities to inspect and test bearings?
Preservation, Cleaning and Packaging.
5.1.3 What is the established history of the bearing? If there
Current edition approved Nov. 1, 2004. Published November 2004. DOI:
10.1520/F2444-04.
has never been a rejection, is inspection warranted?
2
Available from American Bearing Manufacturers Association (ABMA), 2025
5.1.4 What type of test is required and how detailed is it?
M Street, NW Suite 800 Washington, DC 20036.
3
5.1.4.1 Rough spin,
Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
4th Floor, New York, NY 10036. 5.1.4.2 Destructive,
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2444 − 04
5.1.4.3 Nondestructive (NDT), 7.2 The training may be divided into two parts. Classroom
5.1.4.4 Disassembly, training may be Part I and performance training may be Part II.
5.1.4.5 Test requires recleaning, relubrication, and repack-
7.3 Personnel must complete all of the training require-
aging of the bearings,
ments.
5.1.
...