iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D5755-02

(Test Method)

Standard Test Method for Microvacuum Sampling and Indirect Analysis of Dust by Transmission Electron Microscopy for Asbestos Structure Number Concentrations

Standard Test Method for Microvacuum Sampling and Indirect Analysis of Dust by Transmission Electron Microscopy for Asbestos Structure Number Concentrations

SCOPE
1.1 This test method covers a procedure to ( a) identify asbestos in dust and (b) provide an estimate of the surface loading of asbestos in the sampled dust reported as the number of asbestos structures per unit area of sampled surface.
1.1.1 If an estimate of the asbestos mass is to be determined, the user is referred to Test Method D 5756.
1.2 This test method describes the equipment and procedures necessary for sampling, by a microvacuum technique, non-airborne dust for levels of asbestos structures. The non-airborne sample is collected inside a standard filter membrane cassette from the sampling of a surface area for dust which may contain asbestos.
1.2.1 This procedure uses a microvacuuming sampling technique. The collection efficiency of this technique is unknown and will vary among substrates. Properties influencing collection efficiency include surface texture, adhesiveness, electrostatic properties and other factors.
1.3 Asbestos identified by transmission electron microscopy (TEM) is based on morphology, selected area electron diffraction (SAED), and energy dispersive X-ray analysis (EDXA). Some information about structure size is also determined.
1.4 This test method is generally applicable for an estimate of the surface loading of asbestos structures starting from approximately 1000 asbestos structures per square centimetre.
1.4.1 The procedure outlined in this test method employs an indirect sample preparation technique. It is intended to disperse aggregated asbestos into fundamental fibrils, fiber bundles, clusters, or matrices that can be more accurately quantified by transmission electron microscopy. However, as with all indirect sample preparation techniques, the asbestos observed for quantification may not represent the physical form of the asbestos as sampled. More specifically, the procedure described neither creates nor destroys asbestos, but it may alter the physical form of the mineral fibers.
1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-Nov-2002
ICS
13.040.20 - Ambient atmospheres
Technical Committee
D22 - Air Quality
Drafting Committee
D22.07 - Sampling, Analysis, Management of Asbestos, and Other Microscopic Particles
Current Stage
Ref Project

Relations

Replaces
ASTM D5755-95 - Standard Test Method for Microvacuum Sampling and Indirect Analysis of Dust by Transmission Electron Microscopy for Asbestos Structure Number Concentrations
Effective Date
10-Nov-2002
Replaced By
ASTM D5755-03 - Standard Test Method for Microvacuum Sampling and Indirect Analysis of Dust by Transmission Electron Microscopy for Asbestos Structure Number Surface Loading
Effective Date
10-Apr-2003
Referred By
ASTM D7390-18e1 - Standard Guide for Evaluating Asbestos in Dust on Surfaces by Comparison Between Two Environments
Effective Date
10-Nov-2002
Referred By
ASTM D1356-20a - Standard Terminology Relating to Sampling and Analysis of Atmospheres
Effective Date
10-Nov-2002
Referred By
ASTM D6620-19 - Standard Practice for Asbestos Detection Limit Based on Counts
Effective Date
10-Nov-2002
Referred By
ASTM E3272-21 - Standard Guide for Collection of Soils and Other Geological Evidence for Criminal Forensic Applications
Effective Date
10-Nov-2002
Referred By
ASTM D7712-18 - Standard Terminology for Sampling and Analysis of Asbestos
Effective Date
10-Nov-2002

Buy Standard

ASTM D5755-02 - Standard Test Method for Microvacuum Sampling and Indirect Analysis of Dust by Transmission Electron Microscopy for Asbestos Structure Number ConcentrationsASTM D5755-02 - Standard Test Method for Microvacuum Sampling and Indirect Analysis of Dust by Transmission Electron Microscopy for Asbestos Structure Number Concentrations
PreviousNext
Standard
ASTM D5755-02 - Standard Test Method for Microvacuum Sampling and Indirect Analysis of Dust by Transmission Electron Microscopy for Asbestos Structure Number Concentrations
English language
13 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: D 5755 – 02
Standard Test Method for
Microvacuum Sampling and Indirect Analysis of Dust by
Transmission Electron Microscopy for Asbestos Structure
1
Number Surface Loading
This standard is issued under the fixed designation D 5755; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope 1.5 The values stated in SI units are to be regarded as the
standard. The values given in parentheses are for information
1.1 This test method covers a procedure to (a) identify
only.
asbestos in dust and (b) provide an estimate of the surface
1.6 This standard does not purport to address all of the
loading of asbestos in the sampled dust reported as the number
safety concerns, if any, associated with its use. It is the
of asbestos structures per unit area of sampled surface.
responsibility of the user of this standard to establish appro-
1.1.1 If an estimate of the asbestos mass is to be determined,
priate safety and health practices and determine the applica-
the user is referred to Test Method D 5756.
bility of regulatory limitations prior to use.
1.2 This test method describes the equipment and proce-
dures necessary for sampling, by a microvacuum technique,
2. Referenced Documents
non-airborne dust for levels of asbestos structures. The non-
2.1 ASTM Standards:
airborne sample is collected inside a standard filter membrane
2
D 1193 Specification for Reagent Water
cassette from the sampling of a surface area for dust which may
3
D 3195 Practice for Rotameter Calibration
contain asbestos.
D 3670 Guide for Determination of Precision and Bias of
1.2.1 This procedure uses a microvacuuming sampling tech-
3
Methods of Committee D-22
nique. The collection efficiency of this technique is unknown
D 5756 Test Method for Microvacuum Sampling and Indi-
and will vary among substrates. Properties influencing collec-
rect Analysis of Dust by Transmission Electron Micros-
tion efficiency include surface texture, adhesiveness, electro-
3
copy for Asbestos Mass Surface Loading
static properties and other factors.
D 6620 Practice for Determining a Detection Limit for
1.3 Asbestos identified by transmission electron microscopy
3
Asbestos Measurements Based on Counts
(TEM) is based on morphology, selected area electron diffrac-
tion (SAED), and energy dispersive X-ray analysis (EDXA).
3. Terminology
Some information about structure size is also determined.
3.1 Definitions:
1.4 This test method is generally applicable for an estimate
3.1.1 asbestiform—a special type of fibrous habit in which
of the surface loading of asbestos structures starting from
the fibers are separable into thinner fibers and ultimately into
approximately 1000 asbestos structures per square centimetre.
fibrils. This habit accounts for greater flexibility and higher
1.4.1 The procedure outlined in this test method employs an
tensile strength than other habits of the same mineral. For more
indirect sample preparation technique. It is intended to disperse
4
information on asbestiform mineralogy, see Refs (1), (2) and
aggregated asbestos into fundamental fibrils, fiber bundles,
(3).
clusters, or matrices that can be more accurately quantified by
3.1.2 asbestos—a collective term that describes a group of
transmission electron microscopy. However, as with all indi-
naturally occurring, inorganic, highly fibrous, silicate domi-
rect sample preparation techniques, the asbestos observed for
nated minerals, which are easily separated into long, thin,
quantification may not represent the physical form of the
flexible fibers when crushed or processed.
asbestos as sampled. More specifically, the procedure de-
scribed neither creates nor destroys asbestos, but it may alter
the physical form of the mineral fibers.
1
This test method is under the jurisdiction of ASTM Committee D22 on
2
Sampling and Analysis of Atmospheres and is the direct responsibility of Subcom- Annual Book of ASTM Standards, Vol 11.01.
3
mittee D22.07 on Sampling and Analysis of Asbestos. Annual Book of ASTM Standards, Vol 11.03.
4
Current edition approved November 10, 2002. Published January 2002. Origi- The boldface numbers in parentheses refer to the list of references at the end of
nally approved in 1995. Last previous edition approved in 1995 as D 5755 - 95. this test method.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E3193-23(Test Method)
Standard Test Method for Measurement of Lead (Pb) by Flame Atomic Absorption Spectrophotometry (FAAS)

SIGNIFICANCE AND USE
5.1 This test method is intended for use with other standards that address the collection and preparation of samples (airborne particulate, dusts by wipe and micro-vacuuming, dried paint chips, and soils) that are obtained during the assessment or mitigation of lead hazards from buildings and related structures.  
5.2 Laboratories analyzing samples obtained during the assessment or mitigation of lead hazards from buildings and related structures shall conform to Practice E1583, or shall be recognized for lead analysis as promulgated by authorities having jurisdiction, or both.  
Note 2: In the United States of America, laboratories performing analysis of samples collected during lead-based paint activities are required to be accredited to ISO/IEC 17025 and to other requirements promulgated by the Environmental Protection Agency (EPA).  
5.3 This test method may also be used to analyze similar samples from other environments such as toxic characteristic extracts of waste sampled using Guide E1908, and soil and sludge as prepared for analysis using U.S. EPA SW-846 Test Method 1311.
SCOPE
1.1 This test method covers the determination of lead (Pb) in airborne particulate, dust by wipe and micro-vacuuming, paint, and soil collected in and around buildings and related structures by flame atomic absorption spectrophotometry (FAAS) and is derived from Test Methods D4185 and E1613.  
1.2 The sensitivity, detection limit, and optimum working concentration for lead (Pb) are given in Table 1.  
1.3 The values stated in SI units are to be regarded as standard. No other values of measurement are included in this standard.  
1.3.1 Exception—The SI and inch-pound units shown for wipe and micro-vacuuming sampling data are to be individually regarded as standard for wipe and micro-vacuuming sampling data (14.4.2 and 14.4.3).  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM D6589-23(Guide)
Standard Guide for Statistical Evaluation of Atmospheric Dispersion Model Performance

SIGNIFICANCE AND USE
5.1 Guidance is provided on designing model evaluation performance procedures and on the difficulties that arise in statistical evaluation of model performance caused by the stochastic nature of dispersion in the atmosphere. It is recognized there are examples in the literature where, knowingly or unknowingly, models were evaluated on their ability to describe something which they were never intended to characterize. This guide is attempting to heighten awareness, and thereby, to reduce the number of “unknowing” comparisons. A goal of this guide is to stimulate development and testing of evaluation procedures that accommodate the effects of natural variability. A technique is illustrated to provide information from which subsequent evaluation and standardization can be derived.
SCOPE
1.1 This guide provides techniques that are useful for the comparison of modeled air concentrations with observed field data. Such comparisons provide a means for assessing a model's performance, for example, bias and precision or uncertainty, relative to other candidate models. Methodologies for such comparisons are yet evolving; hence, modifications will occur in the statistical tests and procedures and data analysis as work progresses in this area. Until the interested parties agree upon standard testing protocols, differences in approach will occur. This guide describes a framework, or philosophical context, within which one determines whether a model's performance is significantly different from other candidate models. It is suggested that the first step should be to determine which model's estimates are closest on average to the observations, and the second step would then test whether the differences seen in the performance of the other models are significantly different from the model chosen in the first step. An example procedure is provided in Appendix X1 to illustrate an existing approach for a particular evaluation goal. This example is not intended to inhibit alternative approaches or techniques that will produce equivalent or superior results. As discussed in Section 6, statistical evaluation of model performance is viewed as part of a larger process that collectively is referred to as model evaluation.  
1.2 This guide has been designed with flexibility to allow expansion to address various characterizations of atmospheric dispersion, which might involve dose or concentration fluctuations, to allow development of application-specific evaluation schemes, and to allow use of various statistical comparison metrics. No assumptions are made regarding the manner in which the models characterize the dispersion.  
1.3 The focus of this guide is on end results, that is, the accuracy of model predictions and the discernment of whether differences seen between models are significant, rather than operational details such as the ease of model implementation or the time required for model calculations to be performed.  
1.4 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This guide cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This guide is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should it be applied without consideration of a project's many unique aspects. The word “Standard” in the title of this guide means only that the document has been approved through the ASTM consensus process.  
1.5 This standard applies to gaussian plume models; it may not be applicable to non-point sources, heavy gas models from evaporation from pool (for example, liquid spills), as well as near-field receptors.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this guide...

  • Guide
    18 pages
    English language
    sale 15% off
  • Guide
    18 pages
    English language
    sale 15% off
ASTM
ASTM D7440-23(Practice)
Standard Practice for Characterizing Uncertainty in Air Quality Measurements

SIGNIFICANCE AND USE
6.1 A primary use intended for this practice is for qualifying ASTM International Standards as Standard Test Methods. In the past, a “Precision and Bias” report has been required. However, recently a statement of uncertainty has become an acceptable alternative to Guide D3670. Inclusion of such a statement with a method description simplifies comparison of ASTM Test Methods to analogous ISO and Committee for European Normalization (CEN) standards, now required to have uncertainty statements.  
6.2 Standardizing the characterization of sampling/analytical method performance is expected to be useful in other applications as well. For example, performance details are a necessity for justifying compliance decisions based on experimental air quality assessments (7). Documented uncertainty can form a basis for specific criteria defining acceptable sampling/analytical method performance.  
6.3 Furthermore, high quality atmospheric measurements are vital for making decisions as to how hazardous substances are to be controlled. Valid data are required for drawing reasonable epidemiological conclusions, for making sound decisions as to acceptable limits, as well as for determining the efficacy of a hazard control system.  
6.4 Finally, because of developing world-wide acceptance of ISO GUM for detailing measurements when statistics are simple, the practice should be useful in comparing ASTM International Test Methods to other published methods. The codification of statistical procedures may in fact minimize the difficulty in interpreting a plethora of individual, albeit possibly valid, approaches.
SCOPE
1.1 This practice is for assisting developers and users of air quality methods for sampling concentrations of both airborne and settled materials in characterizing measurements as to uncertainty. Where possible, analysis into uncertainty components as recommended in the International Organization for Standardization (ISO) Guide to the Expression of Uncertainty in Measurement (ISO GUM, (1)2) is suggested. Aspects of uncertainty estimation particular to air quality measurement are emphasized. For example, air quality assessment is often complicated by: the difficulty of taking replicate measurements owing to the large spatio-temporal variation in concentration values to be measured; systematic error or bias, both corrected and uncorrected; and the (rare) non-normal distribution of errors. This practice operates mainly through example. Background and mathematical development are relegated to appendices for optional reading.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    14 pages
    English language
    sale 15% off
ASTM
ASTM D7520-16(2023)(Test Method)
Standard Test Method for Determining the Opacity of a Plume in the Outdoor Ambient Atmosphere

SIGNIFICANCE AND USE
5.1 Air permits from regulatory agencies often require measurements of opacity from stationary air pollution point sources in the outdoor ambient environment. Opacity has been visually measured by certified smoke readers in accordance with USEPA (USEPA Method 9). DCOT is also a method to determine plume opacity in the outdoor ambient environment.  
5.2 The concept of DCOT was based on previous method development using Digital Still Cameras and field testing of those methods.7,8 The purpose of this standard is to set a minimum level of performance for products that use DCOT to determine plume opacity in ambient environments.
SCOPE
1.1 This test method describes the procedures to determine the opacity of a plume, using digital imagery and associated hardware and software. The aforementioned plume is caused by particulate matter emitted from a stationary point source in the outdoor ambient environment.  
1.2 The opacity of emissions is determined by the application of a Digital Camera Opacity Technique (DCOT) that consists of a Digital Still Camera, Analysis Software, and the Output Function’s content to obtain and interpret digital images to determine and report plume opacity.  
1.3 This method is suitable to determine the opacity of plumes from zero (0) percent to one hundred (100) percent.  
1.4 Conditions that shall be considered when using this method to obtain the digital image of the plume include the plume’s background, the existence of condensed water in the plume, orientation of the Digital Still Camera to the plume and the sun (see Section 8).  
1.5 This standard describes the procedures to certify the DCOT, hardware, software, and method to determine the opacity of the plumes.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    22 pages
    English language
    sale 15% off
ASTM
ASTM D7788-14(2023)(Practice)
Standard Practice for Collection of Total Airborne Fungal Structures via Inertial Impaction Methodology

SIGNIFICANCE AND USE
4.1 This practice is intended for the collection of airborne fungal spores or fragments, or both, using inertial impaction.  
4.2 It is the responsibility of the user to assure that they are in compliance with all local, state and federal regulations governing the inspection of buildings for fungal colonization and the collection of associated samples.  
4.3 This practice is intended to provide the user with a basic understanding of the equipment, materials and instructions necessary to effectively collect air samples using an inertial impactor.  
4.4 This practice, when properly executed, may also be used for the evaluation of other types of airborne particles with the capturing characteristics appropriate for inertial impactor, and for which appropriate analytical methods exist. Such particles may include dust mites, skin cells, pollen, and other materials.
SCOPE
1.1 The purpose of this practice is to describe procedures for the collection of airborne fungal spores or fragments, or both, using inertial impaction sampling techniques.  
1.2 This practice is not intended to limit the user from the collection of other airborne particulates that may be of interest and captured through this technique.  
1.3 This practice presumes that the user has a fundamental understanding of field investigative techniques related to the scientific process, and sampling plan development and implementation. It is important to establish the related hypothesis to be tested and the supporting analytical methodology needed in order to identify the sampling media to be used and the laboratory conditions for analysis.  
1.4 This practice does not address the development of a formal hypothesis or the establishment of appropriate and defensible investigation and sampling objectives. It is presumed the investigator has the experience and knowledge base to address these issues.  
1.5 This practice does not provide the user sufficient information to allow for interpretation of the analytical results from sample collection. It is the user's responsibility to seek or obtain the information and knowledge necessary to interpret the sample results reported by the laboratory.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6196-23(Practice)
Standard Practice for Choosing Sorbents, Sampling Parameters and Thermal Desorption Analytical Conditions for Monitoring Volatile Organic Chemicals in Air

SIGNIFICANCE AND USE
5.1 This practice is recommended for use in measuring the concentration of VOCs in ambient, indoor, and workplace atmospheres. It may also be used for measuring emissions from materials in small or full scale environmental chambers for material emission testing or human exposure assessment.  
5.2 Such measurements in ambient air are of importance because of the known role of VOCs as ozone precursors, and in some cases (for example, benzene), as toxic pollutants in their own right.  
5.3 Such measurements in indoor air are of importance because of the association of VOCs with air quality problems in indoor environments, particularly in relation to sick building syndrome and emissions from building materials. Many volatile organic compounds have the potential to contribute to air quality problems in indoor environments and in some cases toxic VOCs may be present at such elevated concentrations in home or workplace atmospheres as to prompt serious concerns over human exposure and adverse health effects (5).  
5.4 Such measurements in workplace air are of importance because of the known toxic effects of many such compounds.
Note 1: While workplace air monitoring has traditionally been carried out using disposable sorbent tubes, typically packed with charcoal and extracted using chemical desorption (solvent extraction) prior to GC analysis – for example following NIOSH and OSHA reference methods – routine thermal desorption (TD) technology was originally developed specifically for this application area. TD overcomes the inherent analyte dilution limitation of solvent extraction improving method detection limits by 2 or 3 orders of magnitude and making methods easier to automate. Relevant international standard methods include ISO 16017-1 and ISO 16017-2. For a detailed history of the development of analytical thermal desorption and a comparison with solvent extraction methods see Ref (6).  
5.5 In order to protect the environment as a whole and human health in part...
SCOPE
1.1 This practice is intended to assist in the selection of sorbents and procedures for the sampling and analysis of ambient (1),2 indoor (2), and workplace (3, 4) atmospheres for a variety of common volatile organic compounds (VOCs). It may also be used for measuring emissions from materials in small or full scale environmental chambers or for human exposure assessment.  
1.2 This practice is based on the sorption of VOCs from air onto selected sorbents or combinations of sorbents. Sampled air is either drawn through a tube containing one or a series of sorbents (pumped sampling) or allowed to diffuse, under controlled conditions, onto the sorbent surface at the sampling end of the tube (diffusive or passive sampling). The sorbed VOCs are subsequently recovered by thermal desorption and analyzed by capillary gas chromatography.  
1.3 This practice applies to three basic types of samplers that are compatible with thermal desorption: (1) pumped sorbent tubes containing one or more sorbents; (2) axial passive (diffusive) samplers (typically of the same physical dimensions as standard pumped sorbent tubes and containing only one sorbent); and (3) radial passive (diffusive) samplers.  
1.4 This practice recommends a number of sorbents that can be packed in sorbent tubes for use in the sampling of vapor-phase organic chemicals; including volatile and semi-volatile organic compounds which, generally speaking, boil in the range 0 °C to 400 °C (v.p. 15 kPa to 0.01 kPa at 25 °C).  
1.5 This practice can be used for the measurement of airborne vapors of these organic compounds over a wide concentration range.  
1.5.1 With pumped sampling, this practice can be used for the speciated measurement of airborne vapors of VOCs in a concentration range of approximately 0.1 μg/m3 to 1 g/m3, for individual organic compounds in 1 L to 10 L air samples. Quantitative measurements are possible when using validated procedures with appropri...

  • Standard
    32 pages
    English language
    sale 15% off
  • Standard
    32 pages
    English language
    sale 15% off
ASTM
ASTM E2115-22(Guide)
Standard Guide for Conducting Lead Hazard Assessments of Dwellings and of Other Child-Occupied Facilities

SIGNIFICANCE AND USE
5.1 This guide is intended to help prevent lead poisoning of children by providing standardized procedures for conducting a lead hazard assessment and providing information needed to develop and recommend lead hazard control options as described in Practice E2252.  
5.2 This guide is applicable for use in either occupied or unoccupied dwellings and in other child-occupied facilities.  
5.3 The procedures in this guide, when supplemented by recommendations for controlling lead hazards, provide for the conduct of a lead risk assessment of a dwelling or of other child-occupied facilities.  
5.4 This guide may be used to supplement assessment procedures used to determine the causes of elevated blood lead (EBL) levels in young children.
Note 2: In cases of EBL levels, investigation of the total living environment of the child and a pediatric medical evaluation may also be needed. Reference should be made to documents such as Managing Elevated Blood Lead Levels Among Young Children,6 Preventing Lead Poisoning in Young Children (1991),7 the HUD Guidelines, and Screening Young Children for Lead Poisoning (1997).7  
5.5 Although this guide was developed for dwellings and for other child-occupied facilities, this guide may be suitable for lead hazard assessments in non-residential buildings and other properties following agreement between assessor and client on appropriate lead action levels.  
5.6 This guide is not intended for use in identifying building materials that when abraded or otherwise degraded, such as that which may occur in remodeling or renovation activities, may result in lead hazards.  
5.7 Lead hazard assessment reports describe lead hazards identified at the time the assessment was performed. The locations, types, or severities of lead hazards can change over time as a result of property improvement or deterioration, significant changes in property use, or other factors.
Note 3: The term “lead-free” should never be used to describe the absence of ...
SCOPE
1.1 This guide covers how to conduct, document, and report findings of a lead hazard assessment of dwellings and of other child-occupied facilities.  
1.2 Procedures for assessment of personal items, such as toys, dishes, and hobby materials that may contribute to elevated lead levels in blood are not included in this guide.  
1.3 Procedures for random sampling of units within dwellings having multiple units are not included.  
1.4 This guide contains notes, which are explanatory, and are not part of the mandatory requirements of this guide.  
1.5 The values stated in SI units are to be regarded as the standard.  
1.5.1 Exception—The inch-pound and SI units shown for wipe sampling data are to be individually regarded as standard for wipe sampling data.  
1.6 Methods described in this guide may not meet or be allowed by requirements or regulations established by local authorities having jurisdiction. It is the responsibility of the user of this standard to comply with all such requirements and regulations.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    10 pages
    English language
    sale 15% off
  • Guide
    10 pages
    English language
    sale 15% off
ASTM
ASTM D1914-95(2022)(Practice)
Standard Practice for Conversion Units and Factors Relating to Sampling and Analysis of Atmospheres

SIGNIFICANCE AND USE
3.1 ASTM requires the use of SI units in all its publications and their use in reporting atmospheric measurement data. However, there are historic data and even data currently reported that are based on a variety of units of measurement. This practice tabulates factors that are necessary to convert such data to SI and other units of measurement.  
3.2 IEEE/ASTM SI-10 does not list all the conversion factors commonly used in air pollution and meteorological fields. This practice supplements IEEE/ASTM SI-10.  
3.3 The values reported here were obtained from a number of standard publications. They were adjusted to five figures and organized in a rational order. All values reflect the latest information from the 16th General Conference on Weights and Measurements held in 1979.  
3.4 The factors in Table 1 are provided to change units of measurement from one system to related units in other systems, as well as to smaller or larger units in the same system.  
3.5 Values of units in the left column may be converted to values of units in the right column merely by multiplying by the conversion factor provided in the center column.  (A) For specific applications and exceptions, see Terminology D1356.
SCOPE
1.1 This practice provides units and factors useful for members of the air pollution and meteorological communities.  
1.2 This practice is used together with IEEE/ASTM SI-10, which discusses SI units and contains selected conversion factors for inter-relation of SI units and some commonly used non-metric units.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D8406-22(Practice)
Standard Practice for Performance Evaluation of Ambient Outdoor Air Quality Sensors and Sensor-based Instruments for Portable and Fixed-point Measurement

SIGNIFICANCE AND USE
5.1 This practice establishes standardized tests for the performance evaluation of sensor-based continuous instruments for ambient air quality measurements. Public and private air monitoring interests have manifested themselves as a driving force for the deployment of air quality sensors and instruments to quantify air pollutant concentrations in communities, around schools, around industrial facilities, and elsewhere. Users of air quality sensors require information on the performance and limitations of these devices so that informed decisions regarding their suitability for various purposes can be determined. This practice describes both laboratory and field tests that provide information on candidate instrument repeatability, sensitivity, linearity, cross-interferences, drift and comparability with more costly instruments typically used by entities such as government agencies. The air quality sensors are first evaluated in a laboratory chamber by comparing their response to a reference instrument and challenging the gas sensors with interferents. The sensors are then deployed outdoors for field testing at two sites with different climates against reference air quality instruments. This practice is intended to be referenced in standards and codes that establish minimum performance quality for sensor-based ambient outdoor air monitoring.  
5.2 This practice is intended for air quality sensors that measure one or more of the criteria pollutants in ambient air (ozone, carbon monoxide, nitrogen dioxide, sulfur dioxide, PM10 and PM2.5) that can be operated in outdoor environments and can log a concentration reading. It is not intended for devices or transducers that require additional enclosures for deployment outdoors or post-processing to convert their output signal into a pollutant concentration reading.  
5.3 It is anticipated that the main users of this practice will be manufacturers, developers, and distributors of outdoor air quality sensors, air quality agenc...
SCOPE
1.1 This practice establishes standardized tests for the performance evaluation of sensor-based continuous instruments for ambient outdoor air quality measurements. It describes both laboratory and field tests that provide information on candidate sensor repeatability, sensitivity, linearity, cross-interferences, drift, and comparability against reference instruments.  
1.2 This practice does not apply to sensors or instruments that remotely measure atmospheric pollutants using open path, lidar, or imaging technology.  
1.3 The evaluation procedures contained in this practice are for sensors that alone or in combination measure outdoor criteria pollutants in ambient air: particulate matter (PM2.5 and PM10), sulfur dioxide (SO2), ozone (O3), carbon monoxide (CO), or nitrogen dioxide (NO2) at concentrations that are relevant to public health.  
1.4 Testing is to be performed by a competent entity able to demonstrate that it operates in conformity with internationally accepted test laboratory quality standards such as ISO/IEC 17025.  
1.5 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D2914-15(2022)(Test Method)
Standard Test Methods for Sulfur Dioxide Content of the Atmosphere (West-Gaeke Method)

SIGNIFICANCE AND USE
5.1 Sulfur dioxide is a major air pollutant, commonly formed by the combustion of sulfur-bearing fuels. The Environmental Protection Agency (EPA) has set primary and secondary air quality standards (7) that are designed to protect the public health and welfare.  
5.2 The Occupational Safety and Health Administration (OSHA) has promulgated exposure limits for sulfur dioxide in workplace atmospheres (8).  
5.3 These methods have been found satisfactory for measuring sulfur dioxide in ambient and workplace atmospheres over the ranges pertinent in 5.1 and 5.2.  
5.4 Method A has been designed to correspond to the EPA-Designated Reference Method (7) for the determination of sulfur dioxide.
SCOPE
1.1 These test methods cover the bubbler collection and colorimetric determination of sulfur dioxide (SO2) in the ambient or workplace atmosphere.  
1.2 These test methods are applicable for determining SO2 over the range from approximately 25 μg/m3 (0.01 ppm(v)) to 1000 μg/m3 (0.4 ppm(v)), corresponding to a solution concentration of 0.03 μg SO2/mL to 1.3 μg SO2/mL. Beer's law is followed through the working analytical range from 0.02 μg SO2/mL to 1.4 μg SO2/mL.  
1.3 The lower limit of detection is 0.075 μg SO2/mL (1),2 representing an air concentration of 25 μg SO2/m3 (0.01 ppm(v)) in a 30-min sample, or 13 μg SO2/m3 (0.005 ppm(v)) in a 24-h sample.  
1.4 These test methods incorporate sampling for periods between 30 min and 24 h.  
1.5 These test methods describe the determination of the collected (impinged) samples. A Method A and a Method B are described.  
1.6 Method A is preferred over Method B, as it gives the higher sensitivity, but it has a higher blank. Manual Method B is pH-dependent, but is more suitable with spectrometers having a spectral band width greater than 20 nm.
Note 1: These test methods are applicable at concentrations below 25 μg/m3 by sampling larger volumes of air if the absorption efficiency of the particular system is first determined, as described in Annex A4.
Note 2: Concentrations higher than 1000 μg/m3 can be determined by using smaller gas volumes, larger collection volumes, or by suitable dilution of the collected sample with absorbing solution prior to analysis.  
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.8 Warning—Mercury has been designated by many regulatory agencies as a hazardous material that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see 8.3.1, Section 9, and A3.1.3.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    15 pages
    English language
    sale 15% off