ASTM C834-10

Standard Specification for Latex Sealants

ABSTRACT
This specification covers latex sealants used for sealing joints in building construction. The following are the type and grade of sealant under this specification: Type OP, Type C, Grade 18°C, Grade 0°C, and Grade NF. The sealant shall be composed of latex formulated with appropriate fillers, pigments, and chemical additives. The physical properties of the sealant shall conform to the specified requirements according to type and grade. The following tests shall be done: extrudability after aging, artificial weathering, volume shrinkage, low-temperature flexibility, extension-recovery and adhesion, slump, staining, and tack-free time.
SIGNIFICANCE AND USE
This specification covers two types and three grades of latex sealants as described in Section 4 that are formulated for general caulking and sealing operations in building construction. It should be recognized by the user that not all sealants meeting this specification are suitable for all applications and all substrates. It is essential, therefore, that the type and grade be specified for proper description of a sealant. Test methods relate to special standard substrates of glass, wood and aluminum. If tests are required using substrates in addition to or other than standard, they should be so specified for testing.
Refer to Guide C1193 for information on the proper use of sealants meeting this specification.
SCOPE
1.1 This specification covers one component latex sealants used for sealing joints in building construction.
1.2 A sealant meeting the requirements of this specification shall be classified by the manufacturer to be one of the types and grades defined in Section 4.
1.3 The values stated in SI units are to be regarded as the standard. The inch-pound in parenthesis are provided for information purposes only.
1.4 The following precautionary caveat pertains only to the test method portion, Section 10, of this Specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—Currently, there is no ISO standard similar to this specification.

General Information

• Status: Historical
• Publication Date: 31-Dec-2009
• ICS: 91.100.50 - Binders. Sealing materials
• Technical Committee: C24 - Building Seals and Sealants
• Drafting Committee: C24.10 - Specifications, Guides and Practices

Relations

• Replaces: ASTM C834-05 - Standard Specification for Latex Sealants
• Effective Date: 01-Jan-2010
• Replaced By: ASTM C834-14 - Standard Specification for Latex Sealants
• Effective Date: 01-Jun-2014
• Referred By: ASTM C1021-08(2023) - Standard Practice for Laboratories Engaged in Testing of Building Sealants
• Effective Date: 01-Jan-2010
• Referred By: ASTM C1481-12(2017) - Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS)
• Effective Date: 01-Jan-2010
• Referred By: ASTM C919-22 - Standard Practice for Use of Sealants in Acoustical Applications
• Effective Date: 01-Jan-2010
• Referred By: ASTM E2112-23 - Standard Practice for Installation of Exterior Windows, Doors and Skylights
• Effective Date: 01-Jan-2010
• Referred By: ASTM C1193-16(2023) - Standard Guide for Use of Joint Sealants
• Effective Date: 01-Jan-2010

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C834 −10
StandardSpecification for
1
Latex Sealants
This standard is issued under the fixed designation C834; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope C1241 Test Method for Volume Shrinkage of Latex Sealants
During Cure
1.1 This specification covers one component latex sealants
D2202 Test Method for Slump of Sealants
used for sealing joints in building construction.
D2203 Test Method for Staining from Sealants
1.2 A sealant meeting the requirements of this specification
D2377 Test Method for Tack-Free Time of Caulking Com-
shall be classified by the manufacturer to be one of the types
pounds and Sealants
and grades defined in Section 4.
3. Terminology
1.3 The values stated in SI units are to be regarded as the
standard. The inch-pound in parenthesis are provided for
3.1 Definitions—Definitions of the following terms apply to
information purposes only. thisspecificationandarefoundinTerminologyC717:adhesive
failure (adhesion loss), cure, joint, latex sealant, sealant,
1.4 The following precautionary caveat pertains only to the
shrinkage (volume), and substrate.
test method portion, Section 10, of this Specification: This
standard does not purport to address all of the safety concerns,
4. Classification of Sealants
if any, associated with its use. It is the responsibility of the user
4.1 A sealant qualifying under this specification shall be
of this standard to establish appropriate safety and health
classified by type and grade as follows:
practices and determine the applicability of regulatory limita-
4.1.1 Type OP—An opaque sealant containing color pig-
tions prior to use.
ments or extender pigments, or both, that has no more than
NOTE 1—Currently, there is no ISO standard similar to this specifica-
30 % volume shrinkage (see 10.1.3).
tion.
4.1.2 Type C—A clear or translucent sealant that has no
more than 50 % volume shrinkage (see 10.1.3).
2. Referenced Documents
4.1.3 Grade –18°C—A sealant that meets the requirements
2
2.1 ASTM Standards:
for low temperature flexibility (see 7.1) when tested at –18°C
C717 Terminology of Building Seals and Sealants
(0°F).
C732 Test Method forAging Effects ofArtificialWeathering
4.1.4 Grade 0°C—Asealant that meets the requirements for
on Latex Sealants
low temperature flexibility (see 7.1) when tested at 0°C (32°F).
C734 Test Method for Low-Temperature Flexibility of Latex
4.1.5 Grade NF—A sealant that does not meet the require-
Sealants After Artificial Weathering
ments for low temperature flexibility of Grade 0°C (see 4.1.4).
C736 Test Method for Extension-Recovery andAdhesion of
Latex Sealants
5. Materials and Manufacture
C1183 Test Method for Extrusion Rate of Elastomeric Seal-
5.1 The sealant shall be composed of latex formulated with
ants
appropriatefillers,pigments,andchemicaladditivestoresultin
C1193 Guide for Use of Joint Sealants
conformance to this specification.
5.2 All material and workmanship shall be in accordance
with good commercial practice. The producer is permitted a
1
This specification is under the jurisdiction of ASTM Committee C24 on
wide latitude in choice of raw materials for making these
Building Seals and Sealants and is the direct responsibility of Subcommittee C24.10
on Specifications, Guides and Practices.
products. Consequently, there is no implication that the com-
Current edition approved Jan. 1, 2010. Published February 2010. Originally
pounds are equivalent in all physical properties.
approved in 1976. Last previous edition approved in 2005 as C834 – 05. DOI:
10.1520/C0834-10.
5.3 The manufacturing process shall be such as will ensure
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
a homogeneous mix, free of defects that would affect
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
serviceability, and provide a consistency suitable for immedi-
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. ate application.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C834−10
6. General Requirements num. If tests are required using substrates in addition to or
other than standard, they should be so specified for testing.
6.1 The sealant in the original unopened container shall
8.2 Refer to Guide C1193 for information on the proper use
meet the requirements of this specification for at least 12
of sealants meeting this specification.
mo
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C834–05 Designation: C834 – 10
Standard Specification for
1
Latex Sealants
This standard is issued under the fixed designation C834; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers one component latex sealants used for sealing joints in building construction.
1.2 A sealant meeting the requirements of this specification shall be classified by the manufacturer to be one of the types and
grades defined in Section 4.
1.3 The values stated in SI units are to be regarded as the standard. The inch-pound in parenthesis are provided for information
purposes only.
1.4 The following precautionary caveat pertains only to the test method portion, Section 10, of this Specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
NOTE 1—Currently, there is no ISO standard similar to this specification.
2. Referenced Documents
2
2.1 ASTM Standards:
C717 Terminology of Building Seals and Sealants
C732 Test Method for Aging Effects of Artificial Weathering on Latex Sealants
C734 Test Method for Low-Temperature Flexibility of Latex Sealants After Artificial Weathering
C736 Test Method for Extension-Recovery and Adhesion of Latex Sealants
C1183 Test Method for Extrusion Rate of Elastomeric Sealants
C1193 Guide for Use of Joint Sealants
C1241 Test Method for Volume Shrinkage of Latex Sealants During Cure
D2202 Test Method for Slump of Sealants
D2203 Test Method for Staining from Sealants
D2377 Test Method for Tack-Free Time of Caulking Compounds and Sealants
3. Terminology
3.1 Definitions—Definitions of the following terms apply to this specification and are found in Terminology C717: adhesive
failure (adhesion loss), cure, joint, latex sealant, sealant, shrinkage (volume), and substrate.
4. Classification of Sealants
4.1 A sealant qualifying under this specification shall be classified by type and grade as follows:
4.1.1 TypeOP—Anopaquesealantcontainingcolorpigmentsorextenderpigments,orboth,thathasnomorethan30 %volume
shrinkage (see 10.1.3).
4.1.2 Type C—A clear or translucent sealant that has no more than 50 % volume shrinkage (see 10.1.3).
4.1.3 Grade –18°C—Asealant that meets the requirements for low temperature flexibility (see 7.1) when tested at –18°C (0°F).
4.1.4 Grade 0°C—A sealant that meets the requirements for low temperature flexibility (see 7.1) when tested at 0°C (32°F).
4.1.5 Grade NF—A sealant that does not meet the requirements for low temperature flexibility of Grade 0°C (see 4.1.4).
1
This specification is under the jurisdiction of ASTM Committee C24 on Building Seals and Sealants and is the direct responsibility of Subcommittee C24.10 on
Specifications, Guides and Practices.
´1
Current edition approved May 1, 2005. Published June 2005. Originally approved in 1976. Last previous edition approved in 2000 as C834–00 . DOI: 10.1520/C0834-05.
Current edition approved Jan. 1, 2010. Published February 2010. Originally approved in 1976. Last previous edition approved in 2005 as C834 – 05. DOI:
10.1520/C0834-10.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C834 – 10
5. Materials and Manufacture
5.1 The sealant shall be composed of latex formulated with appropriate fillers, pigments, and chemical additives to result in
conformance to this specification.
5.2 All material and workmanship shall be in accordance with good commercial practice. The producer is permitted a wide
latitude in choice of raw materials for making these products. Consequently, there is no implication that the compounds are
equivalent in all physical properties.
5.3 The manufacturing process shall be such as will ensure a homogeneous mix, free of defects that
...