iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F2511-05e1

(Specification)

Standard Specification for Rollers, Bearing, Needle, Ferrous, Solid

Standard Specification for Rollers, Bearing, Needle, Ferrous, Solid

ABSTRACT
This specification covers the procurement requirements for solid ferrous needle rollers, including the MS19065 spherical ended solid ferrous needle rollers, intended for use in bearings and bearing applications. Rollers shall be made of chrome alloy steel E52100, and manufactured in any of the following types: Type I—spherical end; Type II—flat end; Type III—ball end; Type IV—crankpin end; Type V—conical end; and Type VI—trunnion end. Representative rollers shall be inspected by dimensional and visual examination, surface roughness examination, hot acid etch test, decarburization test, hardness test, chemical analysis, macro-examination, austenitic grain size test, and inclusion rating test.
SCOPE
1.1 This specification covers the procurement requirements for solid ferrous needle bearing rollers including the MS19065 spherical ended solid ferrous needle rollers as specified in Specification F 2443.
1.2 Intended UseThe rollers covered in this specification are intended for use in bearings and bearing applications.
1.3 This specification contains many of the requirements of MIL-R-22440, which was originally developed by the Department of Defense and maintained by the Defense Supply Center in Richmond. The following government activity codes may be found in the Department of Defense, Standardization Directory SD-1.
1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parenthesis are provided for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Jul-2005
ICS
21.100.01 - Bearings in general
Technical Committee
F34 - Rolling Element Bearings
Drafting Committee
F34.01 - Rolling Element
Current Stage
Ref Project

Relations

Replaces
ASTM F2511-05 - Standard Specification for Rollers, Bearing, Needle, Ferrous, Solid
Effective Date
01-Aug-2005

Buy Standard

ASTM F2511-05e1 - Standard Specification for Rollers, Bearing, Needle, Ferrous, SolidASTM F2511-05e1 - Standard Specification for Rollers, Bearing, Needle, Ferrous, Solid
PreviousNext
Technical specification
ASTM F2511-05e1 - Standard Specification for Rollers, Bearing, Needle, Ferrous, Solid
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation:F2511 −05
StandardSpecification for
1
Rollers, Bearing, Needle, Ferrous, Solid
This standard is issued under the fixed designation F2511; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
´ NOTE—8.1.2.1 was editorially corrected in August 2007.
1. Scope A295/A295M Specification for High-Carbon Anti-Friction
Bearing Steel
1.1 This specification covers the procurement requirements
A751 Test Methods, Practices, and Terminology for Chemi-
for solid ferrous needle bearing rollers including the MS19065
cal Analysis of Steel Products
spherical ended solid ferrous needle rollers as specified in
D1974 Practice for Methods of Closing, Sealing, and Rein-
Specification F2443.
forcing Fiberboard Boxes
1.2 Intended Use—The rollers covered in this specification
D3951 Practice for Commercial Packaging
are intended for use in bearings and bearing applications.
D3953 Specification for Strapping, Flat Steel and Seals
1.3 This specification contains many of the requirements of D5118/D5118M PracticeforFabricationofFiberboardShip-
ping Boxes
MIL-R-22440, which was originally developed by the Depart-
ment of Defense and maintained by the Defense Supply Center D5168 Practice for Fabrication and Closure of Triple-Wall
Corrugated Fiberboard Containers
inRichmond.Thefollowinggovernmentactivitycodesmaybe
foundintheDepartmentofDefense,StandardizationDirectory D6251/D6251M Specification forWood-Cleated Panelboard
2
Shipping Boxes
SD-1.
E18 Test Methods for Rockwell Hardness of Metallic Ma-
Preparing Activity Custodians Review Activities
DLA-GS4 Army-AT Army-CR4 terials
Navy-OS Air Force-84
E140 Hardness Conversion Tables for Metals Relationship
Air Force-99
Among Brinell Hardness, Vickers Hardness, Rockwell
DLA-GS4
Hardness, Superficial Hardness, Knoop Hardness, and
1.4 The values stated in inch-pound units are to be regarded
Scleroscope Hardness
as the standard. The values given in parenthesis are provided
E381 Method of Macroetch Testing Steel Bars, Billets,
for information only.
Blooms, and Forgings
1.5 This standard does not purport to address all of the
E384 Test Method for Knoop and Vickers Hardness of
safety concerns, if any, associated with its use. It is the
Materials
responsibility of the user of this standard to establish appro-
F2443 Specification for Roller, Bearing, Needle, Ferrous,
priate safety and health practices and determine the applica-
Solid, Spherical End
bility of regulatory limitations prior to use.
4
2.2 ANSI Standards:
ASME B46.1 Surface Texture (Surface Roughness,
2. Referenced Documents
Waviness, and Lay)
3
2.1 ASTM Standards:
ASME Y14.5 Dimensioning and Tolerancing
ANSI/ASQ Z1.4 Sampling Procedures and Tables for In-
spection by Attributes
1
ThisspecificationisunderthejurisdictionofASTMCommitteeF34onRolling
5
2.3 ISO Standards:
Element Bearings and is the direct responsibility of Subcommittee F34.01 on
Rolling Element. ISO 5593 Rolling Bearings—Vocabulary
Current edition approved Aug. 1, 2005. Published August 2005. DOI: 10.1520/
ISO 10012–1 Quality Assurance Requirements for Measur-
F2511-05E01.
ing Equipment
2
The Military codes that are listed in SD-1 give the address and phone numbers
of the DoD contacts. These are found in the DoD’s ASSIST website http://
assist.daps.dla.mil/online/start/.
3 4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM 4th Floor, New York, NY 10036.
5
Standards volume information, refer to the standard’s Document Summary page on Available from International Organization for Standardization (ISO), 1 rue de
the ASTM website. Varembé, Case postale 56, CH-1211, Geneva 20, Switzerland.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
´1
F2511−05
6
2.4 Military Standards: 5.1.5 Quantity required,
MIL-PRF-121 Barrier Materials, Greaseproof, Waterproof,
5.1.6 Dimensions and tolerances governing formulation of
Flexible, Heat-Sealable
roller ends, if different than 8.1,
MIL-STD-129 Military Marking for Shipment and Storage
5.1.7 Inspection records required (see 16.1.1),
MIL-PRF-131 Barrier Materials, Watervaporproof,
5.1.8 Required levels of packaging (see 15.1),
Greaseproof, Flexible, Heat-Sealable
5.1.9 Preservative required, if different than 15.2.1.2 and
MIL-STD-2073-1 DODStandardPracticeforMilitar
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F2488-05(2022)(Terminology)
Standard Terminology for Rolling Element Bearings

SCOPE
1.1 This terminology covers terms and their definitions relevant to the materials and processes associated with rolling element bearings.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F2511-05(2022)(Specification)
Standard Specification for Rollers, Bearing, Needle, Ferrous, Solid

ABSTRACT
This specification covers the procurement requirements for solid ferrous needle rollers, including the MS19065 spherical ended solid ferrous needle rollers, intended for use in bearings and bearing applications. Rollers shall be made of chrome alloy steel E52100, and manufactured in any of the following types: Type I—spherical end; Type II—flat end; Type III—ball end; Type IV—crankpin end; Type V—conical end; and Type VI—trunnion end. Representative rollers shall be inspected by dimensional and visual examination, surface roughness examination, hot acid etch test, decarburization test, hardness test, chemical analysis, macro-examination, austenitic grain size test, and inclusion rating test.
SCOPE
1.1 This specification covers the procurement requirements for solid ferrous needle bearing rollers including the MS19065 spherical ended solid ferrous needle rollers as specified in Specification F2443.  
1.2 Intended Use—The rollers covered in this specification are intended for use in bearings and bearing applications.  
1.3 This specification contains many of the requirements of MIL-R-22440, which was originally developed by the Department of Defense and maintained by the Defense Supply Center in Richmond. The following government activity codes may be found in the Department of Defense, Standardization Directory SD-1.2    
Preparing Activity  
Custodians  
Review Activities  
DLA-GS4  
Army-AT  
Army-CR4  
Navy-OS  
Air Force-84  
Air Force-99  
DLA-GS4  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM F2161-21(Guide)
Standard Guide for Instrument and Precision Bearing Lubricants—Part 1 Oils

SIGNIFICANCE AND USE
4.1 The purpose of this guide is to report on the testing of, to discuss and compare the properties of, and to provide guidelines for the choice of lubricants for precision rolling element bearings (PREB). The PREB are, for the purposes of this guide, meant to include bearings of ABEC 5 quality and above. This guide limits its scope to oils used in PREB and is to be followed by a similar document to encompass greases used in PREB.  
4.2 The number of lubricants, both oils and greases, used in PREB increased dramatically from the early 1940s to the mid 1990s. In the beginning of this period, petroleum products were the only widely available base stocks. Later, synthetic lubricants became available including synthetic hydrocarbons, esters, silicones, and fluorinated materials, including perfluorinated ethers and the fluorosilicones. This broad spectrum of lubricant choices has led to the use of a large number of different lubricants in PREB applications. The U.S. Department of Defense, as a user of many PREB, has seen a significant increase in the logistics effort required to support the procurement and distribution of these items. In addition, as time has passed some of the lubricants used in certain PREB are no longer available. The SRG Series, LSO-26, and Teresso V-78 are examples of such lubricants. This implies that replacement lubricants must be found as, in this era of extending the lifetime of DoD assets, stockpiles of replacement parts become depleted.  
4.3 One of the primary goals of this study was to take a broad spectrum of the lubricants used in PREB and do a comprehensive series of tests on them in order that their properties could be compared and, if necessary, potential replacement lubricants identified. This study is also meant to be a design guide for choosing lubricants for PREB applications. This guide represents a collective effort of many members of this community who span the spectrum from bearing manufacturers, original equipment manufacture...
SCOPE
1.1 This guide is a tool to aid in the choice of an oil for precision rolling element bearing applications. There are two areas where this guide should have the greatest impact: (1) when a lubricant is being chosen for a new bearing application and (2) when a lubricant for a bearing has to be replaced because the original lubricant specified for the bearing can no longer be obtained. The Report (Section 5) contains a series of tests performed by the same laboratory on a wide variety of oils commonly used in bearing applications to allow comparisons of those properties of the oil that the committee thought to be most important when making a choice of lubricant. This guide contains a listing of the properties of oils by chemical type, that is, ester, silicone, and so forth. This organization is necessary since the operational requirements in a particular bearing application may limit the choice of lubricant to a particular chemical type due to its temperature stability, viscosity index or temperature-vapor pressure characteristics, and so forth. The Report includes the results of tests on the oils included in this study. The Report recommends replacement lubricants for those oils tested that are no longer available. The Report also includes a glossary of terms used in describing/discussing the lubrication of precision and instrument bearings. The Report presents a discussion of elastohydrodynamic lubrication as applied to rolling element bearings.  
1.2 Although other compendia of lubricant properties have been published, for example, the Barden Product Standard, Lubricants2 and the NASA Lubricant Handbook for the Space Industry3, none have centered their attention on lubricants commonly used in precision rolling element bearings (PREB). The PREB put a host of unique requirements upon a lubricant. The lubricant must operate at both high and low temperatures. The lubricant must provide lubrication for months, if not years,...

  • Guide
    14 pages
    English language
    sale 15% off
ASTM
ASTM F2444-04(2018)(Practice)
Standard Practice for Damage Prevention of Bearings, and Bearing Components Through Proper Handling Techniques

SIGNIFICANCE AND USE
4.1 This practice covers bearings and bearing components of all material compositions and grades. It may be used to develop a process for adequately handling bearings.  
4.2 Unless the proper conditions of an adequate facility, equipment, and trained personnel are available, it may be better not to inspect the bearings in-house. The danger of contaminating and damaging the bearings may be much greater than the possibility of receiving bearings that will not function.  
4.3 Bearings are easily damaged at the customers' receiving and test areas. In most cases, bearings should be accepted based on the bearing manufacturer’s certification. Certificates of quality (conformance) supplied by the bearing manufacturer may be furnished in lieu of actual performance of such testing by the receiving activity of the bearings. The certificate shall include the name of the purchaser, contract number/PO number, name of the manufacturer or supplier, item identification, name of the material, lot number, lot size, sample size, date of testing, test method, individual test results, and the specification requirements.  
4.4 This practice does not cover clean room requirements of miniature and instrument precision bearings. These bearings require clean room environments in accordance with ISO 14644-1 and ISO 14644-2.
SCOPE
1.1 This practice covers requirements for the handling of all bearings and bearing components.  
1.2 This is a general practice. The individual bearing handling requirements shall be as specified herein or as specified in the contract or purchase order. In the event of any conflict between requirements of this practice and the individual bearing requirements of an OEM drawing, procurement specification, or other specification, the latter shall govern. Many companies, organizations, and bearing users have excellent facilities, equipment, and knowledgeable personnel for handling bearings. The thrust of this practice is for users that do not have this knowledge of bearings.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM F2094/F2094M-18a(Specification)
Standard Specification for Silicon Nitride Bearing Balls

ABSTRACT
This specification covers the establishment of the basic quality, physical/mechanical property, and test requirements for silicon nitride balls Classes I, II, and III to be used for ball bearings and specialty ball applications. Silicon nitride balls should be produced from either silicon nitride powder having the compositional limits from silicon metal powder.
SCOPE
1.1 This specification covers the establishment of the basic quality, physical/mechanical property, and test requirements for silicon nitride balls Classes I, II, and III to be used for ball bearings and specialty ball applications.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM F2488-05(2022)(Terminology)
Standard Terminology for Rolling Element Bearings

SCOPE
1.1 This terminology covers terms and their definitions relevant to the materials and processes associated with rolling element bearings.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F2511-05(2022)(Specification)
Standard Specification for Rollers, Bearing, Needle, Ferrous, Solid

ABSTRACT
This specification covers the procurement requirements for solid ferrous needle rollers, including the MS19065 spherical ended solid ferrous needle rollers, intended for use in bearings and bearing applications. Rollers shall be made of chrome alloy steel E52100, and manufactured in any of the following types: Type I—spherical end; Type II—flat end; Type III—ball end; Type IV—crankpin end; Type V—conical end; and Type VI—trunnion end. Representative rollers shall be inspected by dimensional and visual examination, surface roughness examination, hot acid etch test, decarburization test, hardness test, chemical analysis, macro-examination, austenitic grain size test, and inclusion rating test.
SCOPE
1.1 This specification covers the procurement requirements for solid ferrous needle bearing rollers including the MS19065 spherical ended solid ferrous needle rollers as specified in Specification F2443.  
1.2 Intended Use—The rollers covered in this specification are intended for use in bearings and bearing applications.  
1.3 This specification contains many of the requirements of MIL-R-22440, which was originally developed by the Department of Defense and maintained by the Defense Supply Center in Richmond. The following government activity codes may be found in the Department of Defense, Standardization Directory SD-1.2    
Preparing Activity  
Custodians  
Review Activities  
DLA-GS4  
Army-AT  
Army-CR4  
Navy-OS  
Air Force-84  
Air Force-99  
DLA-GS4  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM B438-21(Specification)
Standard Specification for Bronze-Base Powder Metallurgy (PM) Bearings (Oil-Impregnated)

ABSTRACT
This specification covers sintered bronze, oil-impregnated bearings made primarily from elemental copper, tin, lead, and graphite powders. This specification covers the following variables: Grades (available in three bronze base compositions identifiable by different graphite contents and one leaded bronze grade) and Type (Grades 1 and 2 are available in four types described by specific density ranges. Grade 3 is available in two types and Grade 4 is available in one type). Sintered bronze bearings shall be made by molding or briquetting metal powder mixtures to the proper density. The material shall conform to the required chemical composition for copper, tin, graphite, iron, lead, zinc, nickel, and antimony. The density of bearings supplied impregnated with lubricant shall be within the prescribed limits. Oil content of bearings shall not be less than the prescribed value for each grade and type of material. The material of different grades and types shall conform to the prescribed radial crushing strength requirements. An acceptance specification for the minimum bearing breaking load may be established for any specific standard oil-impregnated bearing. Chemical analysis shall be made for each representative sample of chips, which may be obtained by milling, drilling, filing, or crushing a bearing with clean dry tools without lubrication.
SCOPE
1.1 This specification covers porous metallic sleeve, flange, thrust, and spherical bronze-base bearings that are produced from mixed metal powders utilizing powder metallurgy (PM) technology and then impregnated with oil to supply operating lubrication.  
1.2 Included are the specifications for the chemical, physical, and mechanical requirements of those bronze-base PM materials that have been developed and standardized specifically for use in the manufacture of these self-lubricating bearings.  
1.3 This specification is applicable to the purchase of bronze-base bearings (oil-impregnated) that were formerly covered by military specifications and are intended for government or military applications. Those additional government requirements that only apply to military bearings are listed in the Supplementary Requirements section of this specification.  
1.4 This specification accompanies Specification B439 that covers the requirements for Iron-Base Powder Metallurgy (PM) Bearings, (Oil-Impregnated).  
1.5 Typical applications for bronze-base bearings are listed in Appendix X1.  
1.6 Bearing dimensional tolerance data are shown in Appendix X2, while engineering information regarding installation and operating parameters of PM bearings is included in Appendix X3. Additional useful information on self-lubricating bearings can be found in MPIF Standard 35, ISO 5755 and the technical literature.2  
1.7 With the exception of the values for density and the mass used to determine density, for which the use of the gram per cubic centimetre (g/cm3) and gram (g) units is the industry standard, the values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.8 The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    26 pages
    English language
    sale 15% off
  • Technical specification
    26 pages
    English language
    sale 15% off
ASTM
ASTM F2161-21(Guide)
Standard Guide for Instrument and Precision Bearing Lubricants—Part 1 Oils

SIGNIFICANCE AND USE
4.1 The purpose of this guide is to report on the testing of, to discuss and compare the properties of, and to provide guidelines for the choice of lubricants for precision rolling element bearings (PREB). The PREB are, for the purposes of this guide, meant to include bearings of ABEC 5 quality and above. This guide limits its scope to oils used in PREB and is to be followed by a similar document to encompass greases used in PREB.  
4.2 The number of lubricants, both oils and greases, used in PREB increased dramatically from the early 1940s to the mid 1990s. In the beginning of this period, petroleum products were the only widely available base stocks. Later, synthetic lubricants became available including synthetic hydrocarbons, esters, silicones, and fluorinated materials, including perfluorinated ethers and the fluorosilicones. This broad spectrum of lubricant choices has led to the use of a large number of different lubricants in PREB applications. The U.S. Department of Defense, as a user of many PREB, has seen a significant increase in the logistics effort required to support the procurement and distribution of these items. In addition, as time has passed some of the lubricants used in certain PREB are no longer available. The SRG Series, LSO-26, and Teresso V-78 are examples of such lubricants. This implies that replacement lubricants must be found as, in this era of extending the lifetime of DoD assets, stockpiles of replacement parts become depleted.  
4.3 One of the primary goals of this study was to take a broad spectrum of the lubricants used in PREB and do a comprehensive series of tests on them in order that their properties could be compared and, if necessary, potential replacement lubricants identified. This study is also meant to be a design guide for choosing lubricants for PREB applications. This guide represents a collective effort of many members of this community who span the spectrum from bearing manufacturers, original equipment manufacture...
SCOPE
1.1 This guide is a tool to aid in the choice of an oil for precision rolling element bearing applications. There are two areas where this guide should have the greatest impact: (1) when a lubricant is being chosen for a new bearing application and (2) when a lubricant for a bearing has to be replaced because the original lubricant specified for the bearing can no longer be obtained. The Report (Section 5) contains a series of tests performed by the same laboratory on a wide variety of oils commonly used in bearing applications to allow comparisons of those properties of the oil that the committee thought to be most important when making a choice of lubricant. This guide contains a listing of the properties of oils by chemical type, that is, ester, silicone, and so forth. This organization is necessary since the operational requirements in a particular bearing application may limit the choice of lubricant to a particular chemical type due to its temperature stability, viscosity index or temperature-vapor pressure characteristics, and so forth. The Report includes the results of tests on the oils included in this study. The Report recommends replacement lubricants for those oils tested that are no longer available. The Report also includes a glossary of terms used in describing/discussing the lubrication of precision and instrument bearings. The Report presents a discussion of elastohydrodynamic lubrication as applied to rolling element bearings.  
1.2 Although other compendia of lubricant properties have been published, for example, the Barden Product Standard, Lubricants2 and the NASA Lubricant Handbook for the Space Industry3, none have centered their attention on lubricants commonly used in precision rolling element bearings (PREB). The PREB put a host of unique requirements upon a lubricant. The lubricant must operate at both high and low temperatures. The lubricant must provide lubrication for months, if not years,...

  • Guide
    14 pages
    English language
    sale 15% off
ASTM
ASTM F2444-04(2018)(Practice)
Standard Practice for Damage Prevention of Bearings, and Bearing Components Through Proper Handling Techniques

SIGNIFICANCE AND USE
4.1 This practice covers bearings and bearing components of all material compositions and grades. It may be used to develop a process for adequately handling bearings.  
4.2 Unless the proper conditions of an adequate facility, equipment, and trained personnel are available, it may be better not to inspect the bearings in-house. The danger of contaminating and damaging the bearings may be much greater than the possibility of receiving bearings that will not function.  
4.3 Bearings are easily damaged at the customers' receiving and test areas. In most cases, bearings should be accepted based on the bearing manufacturer’s certification. Certificates of quality (conformance) supplied by the bearing manufacturer may be furnished in lieu of actual performance of such testing by the receiving activity of the bearings. The certificate shall include the name of the purchaser, contract number/PO number, name of the manufacturer or supplier, item identification, name of the material, lot number, lot size, sample size, date of testing, test method, individual test results, and the specification requirements.  
4.4 This practice does not cover clean room requirements of miniature and instrument precision bearings. These bearings require clean room environments in accordance with ISO 14644-1 and ISO 14644-2.
SCOPE
1.1 This practice covers requirements for the handling of all bearings and bearing components.  
1.2 This is a general practice. The individual bearing handling requirements shall be as specified herein or as specified in the contract or purchase order. In the event of any conflict between requirements of this practice and the individual bearing requirements of an OEM drawing, procurement specification, or other specification, the latter shall govern. Many companies, organizations, and bearing users have excellent facilities, equipment, and knowledgeable personnel for handling bearings. The thrust of this practice is for users that do not have this knowledge of bearings.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off