ASTM F2276-10(2015)
(Specification)Standard Specification for Fitness Equipment
Standard Specification for Fitness Equipment
ABSTRACT
This specification establishes parameters for the design and manufacture of fitness equipment intended for use by individuals age 12 and above. The design and construction requirements for the following are specified: (1) stability, (2) support, (3) edges, corners, and tube ends, and (4) moving parts in accessible areas such as rotating and reciprocating points. The equipment shall meet the guarding, enclosure, and spacing requirements specified for: (1) squeeze, shear, and crush points, (2) adjustment and locking means, (3) handgrips (integral, applied, and rotating) and foot support, (4) load development and transmitting components such as ropes, belts, chains, and other means, and chain or gear drives, and (5) intrinsic, extrinsic, and endurance loading. The documentation shall include the following: assembly instructions, list of equipment parts, operational instructions, and maintenance instructions. Adequate warnings or warning labels alerting users, third parties, and service personnel to hazards associated with use and service of the equipment shall be provided for consumer, commercial, and institutional fitness equipment. The requirements for site-specific labels and user weight restrictions are specified.
SCOPE
1.1 This specification establishes parameters for the design and manufacture of fitness equipment as defined in 3.1.9.
1.2 It is intended that these fitness products be used in an indoor setting or environment.
1.3 It is the intent of this specification to specify products for use by individuals age 13 and above.
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F2276 − 10 (Reapproved 2015) An American National Standard
Standard Specification for
1
Fitness Equipment
This standard is issued under the fixed designation F2276; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
The goal of this specification is to promote proper design and manufacturing practices for stationary
fitness equipment. Through these specifications this standard aims to assist designers and manufac-
turers in producing functional, safe products under proper operations. This standard specifies safety
requirements that are generally applicable to all stationary fitness equipment. For specific types of
fitness equipment, these requirements shall be supplemented or superseded by the requirements of
specific standards that have been issued to cover these specific types or groups of fitness products.
Where specific standards exist, this standard should be used in conjunction with the other standards.
Special care is required in applying this standard alone to equipment for which no specific standard
exists.
The equipment user must recognize, however, that a standard alone will not necessarily prevent
injuries. Like other physical activities, exercise involving fitness equipment involves the risk of injury,
particularly if the equipment is used improperly.
1. Scope F1749 Specification for Fitness Equipment and Fitness Fa-
cility Safety Signage and Labels
1.1 This specification establishes parameters for the design
3
2.2 ANSI Standards:
and manufacture of fitness equipment as defined in 3.1.9.
ANSI B29.1 Precision Power Transmission Roller Chains,
1.2 It is intended that these fitness products be used in an
Attachments and Sprockets
4
indoor setting or environment.
2.3 European Standards:
1.3 It is the intent of this specification to specify products EN 957-1 Stationary Training Equipment-Part 1: General
Safety Requirements and Test Methods
for use by individuals age 13 and above.
1.4 The values stated in SI units are to be regarded as the
3. Terminology
standard. The values given in parentheses are for information
3.1 Definitions of Terms Specific to This Standard:
only.
3.1.1 accessible area, n—area accessible to the user or third
1.5 This standard does not purport to address all of the
party when the equipment is in normal use, during setting up,
safety concerns, if any, associated with its use. It is the
grasping, or adjusting of equipment or position of the body.
responsibility of the user of this standard to establish appro-
3.1.1.1 Discussion—This area encompasses a region from
priate safety and health practices and determine the applica-
the floor to a height of 1800 mm (71 in.) above the floor. This
bility of regulatory limitations prior to use.
does not include areas that are accessible during the initial
assembly.
2. Referenced Documents
3.1.2 applied handgrips, n—handgrip that is formed,
2
2.1 ASTM Standards:
molded, or attached to a support, component, or structure.
3.1.3 consumer fitness equipment, n—fitness equipment in-
1
This specification is under the jurisdiction of ASTM Committee F08 on Sports
tended for use by one person or one family unit.
Equipment, Playing Surfaces, and Facilities and is the direct responsibility of
3.1.4 corner, n—intersection of three planes or surfaces on a
Subcommittee F08.30 on Fitness Products.
Current edition approved Oct. 1, 2015. Published December 2015. Originally single component.
approved in 2003. Last previous edition approved in 2010 as F2276 – 10. DOI:
10.1520/F2276-10R15.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM 4th Floor, New York, NY 10036, http://www.ansi.org.
4
Standards volume information, refer to the standard’s Document Summary page on Available from European Committee for Standardization (CEN), 36 rue de
the ASTM website. Stassart, B-1050, Brussels, Belgium, http://www.cenorm.be.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2276 − 10 (2015)
3.1.5 cycle, n—movement of a point or load from a starting component, that when entered causes a portion of the body to
position and back to the same starting position. The cycle being be pulled into and entrapped between the components.
executed through the full range of intended motion.
3.1.23 range of movement, n—space in which the user or
3.1.6 edge,
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2276 − 10 F2276 − 10 (Reapproved 2015) An American National Standard
Standard Specification for
1
Fitness Equipment
This standard is issued under the fixed designation F2276; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
The goal of this specification is to promote proper design and manufacturing practices for stationary
fitness equipment. Through these specifications this standard aims to assist designers and manufac-
turers in producing functional, safe products under proper operations. This standard specifies safety
requirements that are generally applicable to all stationary fitness equipment. For specific types of
fitness equipment, these requirements shall be supplemented or superseded by the requirements of
specific standards that have been issued to cover these specific types or groups of fitness products.
Where specific standards exist, this standard should be used in conjunction with the other standards.
Special care is required in applying this standard alone to equipment for which no specific standard
exists.
The equipment user must recognize, however, that a standard alone will not necessarily prevent
injuries. Like other physical activities, exercise involving fitness equipment involves the risk of injury,
particularly if the equipment is used improperly.
1. Scope
1.1 This specification establishes parameters for the design and manufacture of fitness equipment as defined in 3.1.9.
1.2 It is intended that these fitness products be used in an indoor setting or environment.
1.3 It is the intent of this specification to specify products for use by individuals age 13 and above.
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
F1749 Specification for Fitness Equipment and Fitness Facility Safety Signage and Labels
3
2.2 ANSI Standards:
ANSI B29.1 Precision Power Transmission Roller Chains, Attachments and Sprockets
4
2.3 European Standards:
EN 957-1 Stationary Training Equipment-Part 1: General Safety Requirements and Test Methods
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
1
This specification is under the jurisdiction of ASTM Committee F08 on Sports Equipment, Playing Surfaces, and Facilities and is the direct responsibility of
Subcommittee F08.30 on Fitness Products.
Current edition approved Feb. 1, 2010Oct. 1, 2015. Published March 2010December 2015. Originally approved in 2003. Last previous edition approved in 20092010 as
F2276 – 09.F2276 – 10. DOI: 10.1520/F2276-10.10.1520/F2276-10R15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
4
Available from European Committee for Standardization (CEN), 36 rue de Stassart, B-1050, Brussels, Belgium, http://www.cenorm.be.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2276 − 10 (2015)
3.1.1 accessible area, n—area accessible to the user or third party when the equipment is in normal use, during setting up,
grasping, or adjusting of equipment or position of the body.
3.1.1.1 Discussion—
This area encompasses a region from the floor to a height of 1800 mm (71 in.) above the floor. This does not include areas that
are accessible during the initial assembly.
3.1.2 applied handgrips, n—handgrip that is formed, molded, or attached to a support, component, or structure.
3.1.3 consumer fitness equipment, n—fitness equipment intended for use by one person or one family unit.
3.1.4 corner, n—intersection of three planes or surfaces on a single component.
3.1.5 cycle, n—movement of a point or load from
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.