ASTM F1081-23
(Specification)Standard Specification for Competition Wrestling Mats
Standard Specification for Competition Wrestling Mats
ABSTRACT
This specification establishes the physical and performance requirements for qualifying construction designs of competition wrestling mats used in U.S. collegiate or high school style (Type I), and international free style (Type II) wrestling. All mat constructions are included here, except for felt-core mats enclosed in sewn covers. The mats shall be tested and conform accordingly to tensile strength, shock absorption, and thickness requirements.
SIGNIFICANCE AND USE
5.1 The mats shall be constructed to yield the values listed in Table 1 throughout the mat area under the conditions of the manufacturer's warranty.
5.2 Special requirements for the mats shall be subject to purchase agreements. Special requirements shall never reduce any of the basic requirements listed in this standard.
5.3 Good manufacturing practices shall be used in the construction and inspection of the mats.
SCOPE
1.1 This specification covers competition wrestling mats used at the high school and college levels. All mat constructions are included, except felt-core mats enclosed in sewn covers. The intended use of this standard is for the qualification of construction designs.
Note 1: The known constructions, as of the issuance of this specification are: (1) closed-cell foam cores with polyvinyl chloride (PVC) or PVC copolymer coatings, or both, which are integral parts of the mat; (2) closed-cell foam cores with attached fabric cover; (3) foam cores, either open- or closed-cell enclosed in sewn, loose covers, and (4) molded open-cell PVC foam with a dense skin on one surface which is an integral part of the mat.
Note 2: There is no known ISO equivalent to this standard.
1.2 This specification covers mats used in the two major styles of wrestling: U.S. collegiate or high school, and international free style.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Note 6 for specific hazards statements.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F1081 − 23 An American National Standard
Standard Specification for
1
Competition Wrestling Mats
This standard is issued under the fixed designation F1081; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
1.1 This specification covers competition wrestling mats 2.1 ASTM Standards:
used at the high school and college levels. All mat construc- D412 Test Methods for Vulcanized Rubber and Thermoplas-
tions are included, except felt-core mats enclosed in sewn tic Elastomers—Tension
covers. The intended use of this standard is for the qualification D1056 Specification for Flexible Cellular Materials—
of construction designs. Sponge or Expanded Rubber
D1682 Test Method for Breaking Load and Elongation of
NOTE 1—The known constructions, as of the issuance of this specifi-
3
Textile Fabric (Withdrawn 1992)
cation are: (1) closed-cell foam cores with polyvinyl chloride (PVC) or
F355 Test Method for Impact Attenuation of Playing Surface
PVC copolymer coatings, or both, which are integral parts of the mat; (2)
closed-cell foam cores with attached fabric cover; (3) foam cores, either
Systems, Other Protective Sport Systems, and Materials
open- or closed-cell enclosed in sewn, loose covers, and (4) molded
Used for Athletics, Recreation and Play
open-cell PVC foam with a dense skin on one surface which is an integral
4
2.2 National Collegiate Athletic Association Document:
part of the mat.
NCAA Official Wrestling Rules
NOTE 2—There is no known ISO equivalent to this standard.
5
2.3 U.S. Wrestling Federation Document:
1.2 This specification covers mats used in the two major
International Wrestling Rules, Freestyle, and Greco-Roman
styles of wrestling: U.S. collegiate or high school, and inter-
2.4 National Federation of State High School Associations
national free style.
6
Document:
1.3 The values stated in inch-pound units are to be regarded
Official High School Wrestling Rules
as standard. The values given in parentheses are mathematical
3. Terminology
conversions to SI units that are provided for information only
and are not considered standard.
3.1 Definitions of Terms Specific to This Standard:
3.1.1 coating—Polyvinyl chloride (PVC) or PVC
1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the copolymer, or both, or other suitable polymeric materials.
responsibility of the user of this standard to establish appro-
3.1.2 cure—Evaporation of solvents from coating and
priate safety, health, and environmental practices and deter-
coated foam mats only.
mine the applicability of regulatory limitations prior to use.
4. Classification
See Note 6 for specific hazards statements.
1.5 This international standard was developed in accor-
4.1 Classify mats in accordance with the style of wrestling
dance with internationally recognized principles on standard-
being performed.
ization established in the Decision on Principles for the
4.2 The classifications are:
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
2
Barriers to Trade (TBT) Committee. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
1 3
This specification is under the jurisdiction of ASTM Committee F08 on Sports The last approved version of this historical standard is referenced on
Equipment, Playing Surfaces, and Facilitiesand is the direct responsibility of www.astm.org.
4
Subcommittee F08.12 on Gymnastics and Wrestling Equipment. NCAA, Shawnee Mission, KN 66222.
5
Current edition approved Nov. 1, 2023. Published November 2023. Originally US Wrestling Federation, 405 West Hall of Fame Ave., Stillwater, OK 74074.
6
approved in 1987. Last previous edition approved in 2021 as F1081 – 09 (2021). National Federation of State High School Associations, P.O. Box 20626,
DOI: 10.1520/F1081-23. Kansas City, MO 64195.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1081 − 23
4.2.1 Type I—U.S. collegiate or high school style wrestling. 7.2 A mat shall have a maximum of 20 sections, unless
4.2.2 Type II—International free style wrestling.
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1081 − 09 (Reapproved 2021) F1081 − 23 An American National Standard
Standard Specification for
1
Competition Wrestling Mats
This standard is issued under the fixed designation F1081; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers competition wrestling mats used at the high school and college levels. All mat constructions are
included, except felt-core mats enclosed in sewn covers. The intended use of this standard is for the qualification of construction
designs.
NOTE 1—The known constructions, as of the issuance of this specification are: (1) closed-cell foam cores with polyvinyl chloride (PVC) or PVC
copolymer coatings, or both, which are integral parts of the mat; (2) closed-cell foam cores with attached fabric cover; (3) foam cores, either open- or
closed-cell enclosed in sewn, loose covers, and (4) molded open-cell PVC foam with a dense skin on one surface which is an integral part of the mat.
NOTE 2—There is no known ISO equivalent to this standard.
1.2 This specification covers mats used in the two major styles of wrestling: U.S. collegiate or high school, and international free
style.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use. See Note 6 for specific hazards statements.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D412 Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
D1056 Specification for Flexible Cellular Materials—Sponge or Expanded Rubber
3
D1682 Test Method for Breaking Load and Elongation of Textile Fabric (Withdrawn 1992)
F355 Test Method for Impact Attenuation of Playing Surface Systems, Other Protective Sport Systems, and Materials Used for
Athletics, Recreation and Play
1
This specification is under the jurisdiction of ASTM Committee F08 on Sports Equipment, Playing Surfaces, and Facilitiesand is the direct responsibility of Subcommittee
F08.12 on Gymnastics and Wrestling Equipment.
Current edition approved Dec. 1, 2021Nov. 1, 2023. Published January 2022November 2023. Originally approved in 1987. Last previous edition approved in 20152021
as F1081 – 09 (2015).(2021). DOI: 10.1520/F1081-09R21.10.1520/F1081-23.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1081 − 23
4
2.2 National Collegiate Athletic Association Document:
NCAA Official Wrestling Rules
5
2.3 U.S. Wrestling Federation Document:
International Wrestling Rules, Freestyle, and Greco-Roman
6
2.4 National Federation of State High School Associations Document:
Official High School Wrestling Rules
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 coating—Polyvinyl chloride (PVC) or PVC copolymer, or both, or other suitable polymeric materials.
3.1.2 cure—Evaporation of solvents from coating and coated foam mats only.
4. Classification
4.1 Classify mats in accordance with the style of wrestling being performed.
4.2 The classifications are:
4.2.1 Type I—U.S. collegiate or high school style wrestling.
4.2.2 Type II—International free style wrestling.
5. Significance and Use
5.1 The mats shall be constructed to yield the value
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.