iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM B152/B152M-00

(Specification)

Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar

Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar

SCOPE
1.1 This specification establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the following coppers. Copper UNS No.Previous DesignationAType of CopperC10100 OFEOxygen-free electronicC10200BOF Oxygen-free without residualdeoxidantsC10300 ...Oxygen-free extra low phosphorusC10400, C10500, C10700OFS Oxygen-free, silver bearingC10800 ...Oxygen-free low phosphorusC10910 ...Low oxygenC11000BETP Electrolytic tough pitchC11300, C11400, C11600BSTP Silver bearing tough pitchC12000 DLPPhosphorized, low residual phos-phorusC12200BDHP Phosphorized, high residual phos-phorusC12300 DPSPhosphorized, silver bearingC14200 DPAPhosphorus deoxidized, arsenicalC14420 ...Tin bearing tellurium copperC14530 ...Tin tellurium bearing copperAExcept Copper UNS No. C10300 (oxygen-free extra low phosphorus), No. C10800 (oxygen-free low phosphorus), and C10910 (low oxygen), these types of copper are classified in Classification B 224.
BSAE Specification CA101 conforms to Copper UNS No. C10100; SAE Specification CA102 conforms to the requirements for Copper UNS No. C10200; SAE Specification CA110 conforms to the requirements for Copper UNS No. C11000; SAE Specifications CA113, CA114, and CA116 conform to the requirements for Copper UNS Nos. C11300, C11400, and C11600; SAE Specification CA120 conforms to Copper UNS No. C12000; and SAE Specification CA122 conforms to the requirements for Copper UNS No. C12200.
Note 1--Each of the coppers listed has unique properties that can make it suitable for specific applications. The purchaser should consult with the supplier to determine which copper would be best suited for the intended application.
Note 2--Copper UNS Nos. C10400, C10500, C10700, C11300, C11400, and C11600 identify coppers with specific silver content (see Table 1 ).
Note 3--This specification is not intended to cover material rolled to ounce-weight thicknesses. Such material is covered by Specification B370.
Plates for locomotive fireboxes are covered by Specification B 11.
Flat copper products with finished (rolled or drawn) edges (flat wire and strip) are also covered by Specification B72.
1.1.1 When no specific copper is identified in the contract or purchase order, the supplier may furnish product from any of the listed coppers.
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are provided for information only.
1.3The following safety hazards caveat only pertains to the test method portion, Section 14 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-Nov-2000
ICS
77.150.30 - Copper products
Technical Committee
B05 - Copper and Copper Alloys
Drafting Committee
B05.01 - Plate, Sheet, and Strip
Current Stage
Ref Project

Relations

Replaced By
ASTM B152/B152M-06 - Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
Effective Date
15-Feb-2006
Referred By
ASTM B813-16 - Standard Specification for Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube
Effective Date
10-Nov-2000
Referred By
ASTM D3433-99(2020) - Standard Test Method for Fracture Strength in Cleavage of Adhesives in Bonded Metal Joints
Effective Date
10-Nov-2000
Referred By
ASTM C665-23 - Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing
Effective Date
10-Nov-2000
Referred By
ASTM E18-22 - Standard Test Methods for Rockwell Hardness of Metallic Materials
Effective Date
10-Nov-2000
Referred By
ASTM F2798-09(2023) - Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications
Effective Date
10-Nov-2000
Referred By
ASTM B506-22 - Standard Specification for Copper-Clad Stainless Steel Sheet and Strip for Building Construction
Effective Date
10-Nov-2000
Referred By
ASTM B432-19 - Standard Specification for Copper and Copper Alloy Clad Steel Plate
Effective Date
10-Nov-2000
Referred By
ASTM D849-15(2019)e1 - Standard Test Method for Copper Strip Corrosion by Industrial Aromatic Hydrocarbons
Effective Date
10-Nov-2000
Referred By
ASTM C764-19 - Standard Specification for Mineral Fiber Loose-Fill Thermal Insulation
Effective Date
10-Nov-2000
Referred By
ASTM C739-21a - Standard Specification for Cellulosic Fiber Loose-Fill Thermal Insulation
Effective Date
10-Nov-2000
Referred By
ASTM F375-20 - Standard Specification for Integrated Circuit Lead Frame Material (Withdrawn 2023)
Effective Date
10-Nov-2000
Referred By
ASTM D1002-10(2019) - Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
Effective Date
10-Nov-2000
Referred By
ASTM E746-18 - Standard Practice for Determining Relative Image Quality Response of Industrial Radiographic Imaging Systems
Effective Date
10-Nov-2000
Referred By
ASTM B753-07(2018) - Standard Specification for Thermostat Component Alloys
Effective Date
10-Nov-2000

Buy Standard

ASTM B152/B152M-00 - Standard Specification for Copper Sheet, Strip, Plate, and Rolled BarASTM B152/B152M-00 - Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
PreviousNext
Technical specification
ASTM B152/B152M-00 - Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Used in USDOE-NE standards
Designation: B 152/B 152M – 00
Standard Specification for
1
Copper Sheet, Strip, Plate, and Rolled Bar
This standard is issued under the fixed designation B 152/B 152M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
NOTE 3—This specification is not intended to cover material rolled to
1. Scope*
ounce-weight thicknesses. Such material is covered by Specification
2
1.1 This specification establishes the requirements for cop-
B 370.
per sheet, strip, plate, and rolled bar produced from the
Plates for locomotive fireboxes are covered by SpecificationB11.
following coppers.
Flat copper products with finished (rolled or drawn) edges (flat wire and
strip) are also covered by Specification B 272.
Previous
Copper
Designa-
UNS No. Type of Copper
A 1.1.1 Whennospecificcopperisidentifiedinthecontractor
tion
purchase order, the supplier may furnish product from any of
C10100 OFE Oxygen-free electronic
the listed coppers.
B
C10200 OF Oxygen-free without residual
1.2 The values stated in inch-pound units are to be regarded
deoxidants
C10300 . Oxygen-free extra low phosphorus as the standard. The SI values given in parentheses are
C10400, C10500, C10700 OFS Oxygen-free, silver bearing
provided for information only.
C10800 . Oxygen-free low phosphorus
1.3 The following safety hazards caveat only pertains to the
C10910 . Low oxygen
B
C11000 ETP Electrolytic tough pitch test method portion, Section 14 of this specification: This
B
C11300, C11400, C11600 STP Silver bearing tough pitch
standard does not purport to address all of the safety concerns,
C12000 DLP Phosphorized, low residual phos-
if any, associated with its use. It is the responsibility of the user
phorus
B
C12200 DHP Phosphorized, high residual phos-
of this standard to establish appropriate safety and health
phorus
practices and determine the applicability of regulatory limita-
C12300 DPS Phosphorized, silver bearing
tions prior to use.
C14200 DPA Phosphorus deoxidized, arsenical
C14420 . Tin bearing tellurium copper
C14530 . Tin tellurium bearing copper 2. Referenced Documents
_______________
2.1 ASTM Standards:
A
Except Copper UNS No. C10300 (oxygen-free extra low phosphorus), No.
B11 Specification for Copper Plates for Locomotive Fire-
C10800 (oxygen-free low phosphorus), and C10910 (low oxygen), these types of
3
boxes
copper are classified in Classification B 224.
B
SAE Specification CA101 conforms to Copper UNS No. C10100; SAE Speci-
B 170 Specification for Oxygen-Free Electrolytic Copper—
fication CA102 conforms to the requirements for Copper UNS No. C10200; SAE 4
Refinery Shapes
Specification CA110 conforms to the requirements for Copper UNS No. C11000;
B 193 Test Method for Resistivity of Electrical Conductor
SAE Specifications CA113, CA114, and CA116 conform to the requirements for
5
Copper UNS Nos. C11300, C11400, and C11600; SAE Specification CA120
Materials
conforms to Copper UNS No. C12000; and SAE Specification CA122 conforms to
B 216 Specification forTough-Pitch Fire-Refined Copper—
the requirements for Copper UNS No. C12200.
4
Refinery Shapes
4
NOTE 1—Eachofthecopperslistedhasuniquepropertiesthatcanmake
B 224 Classification of Coppers
it suitable for specific applications. The purchaser should consult with the
B 248 Specification for General Requirements for Wrought
supplier to determine which copper would be best suited for the intended
Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled
application.
4
Bar
NOTE 2—Copper UNS Nos. C10400, C10500, C10700, C11300,
C11400, and C11600 identify coppers with specific silver content (see B 248M Specification for General Requirements for
Table 1).
Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and
4
Rolled Bar [Metric]
B 272 Specification for Copper Flat Products with Finished
4
(Rolled or Drawn) Edges (Flat Wire and Strip)
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB05onCopper
andCopperAlloysandisthedirectresponsibilityofSubcommitteeB05.01onPlate,
Sheet, and Strip.
Current edition approved Nov. 10, 2000. Published January 2001. Originally
3
published as B 152 – 42 T. Last previous edition B 152 – 97a. Discontinued—see 1980 Annual Book of ASTM Standards, Part 6.
2 4
For ASME Boiler and Pressure Vessel Code applications see related Specifi- Annual Book of ASTM Standards, Vol 02.01.
5
cation SB-152 in Section 10 of that Code. Annual Book of ASTM Standards, Vol 02.03.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Bo
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM B820-23(Test Method)
Standard Test Method for Bend Test for Determining the Formability of Copper and Copper Alloy Strip

SIGNIFICANCE AND USE
5.1 This bend test provides information as to the formability or the ability of copper and copper alloy strip to resist cracking when being formed.  
5.2 This test method can be used as a quality control tool to determine if material will form to a given radius.  
5.3 This test method is also useful in research and development to provide data for use in selecting a spring material that will safely form to the geometry of a given part.  
5.3.1 The forming characteristic of interest is the smallest bend radius that can be formed without cracks or otherwise unacceptable surface conditions (8.4). This radius, R, is the radius of curvature of the nose of the punch used in the test.  
5.3.2 In addition, the difference between the angle of the bend after testing and 90° provides a measure of post-forming springback.  
5.4 The results are suitable for direct application in design and manufacturing, only when all factors such as the geometry of the part, punch and die design, lubrication, stamping speed, and other material properties are known.
SCOPE
1.1 This test method covers the technique of bend testing copper and copper alloy strip samples to determine product formability or the ability to resist cracking when forming a bend around a specific radius. The criterion for failure is the occurrence of cracks on the convex surface of the bend.  
1.2 This bend test is limited to strip from 0.003 in. to and including 0.031 in. (0.076 mm to and including 0.79 mm) thick.  
1.3 The forming or punch radius for the bend test shall be determined by agreement between the manufacturer or supplier and purchaser. This punch radius is typically equal to or greater than the minimum bend radius without failure for the alloy, temper and thickness combination of the strip being tested.  
1.4 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM B36/B36M-23(Specification)
Standard Specification for Brass Plate, Sheet, Strip, And Rolled Bar

ABSTRACT
This specification establishes the requirements brass plates, sheets, strips, and rolled bars made from UNS C21000, C22000, C22600, C23000, C24000, C26000, C26800, C27200, or C28000. Plates are generally available only in the hot-rolled temper. The standard tempers of as hot rolled, rolled, annealed, and annealed-to-temper materials are detailed in this specification as well as in other specifications listed herein. This specification also contains information on the required tensile strengths, Rockwell hardness and grain sizes of the materials. The Rockwell hardness test can be used to test for general conformity to the specification requirements for temper, tensile strength and grain size.
SCOPE
1.1 This specification establishes the requirements for brass (copper-zinc alloy) plate, sheet, strip, and rolled bar of the following alloys:    
Copper Alloy
UNS No.  
Type of Metal  
C21000  
Gilding  
C22000  
Commerical Bronze  
C22600  
Jewerly Bronze  
C23000  
Red Brass  
C24000  
Low Brass  
C26000  
Cartridge Brass  
C26800  
Yellow Brass  
C27200  
…  
C28000  
Muntz Metal  
1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification.  
1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM B763/B763M-23(Specification)
Standard Specification for Copper Alloy Sand Castings for Valve Applications

ABSTRACT
This specification establishes requirements for copper alloy sand castings for valve applications. The castings shall conform to the chemical composition requirements specified. Mechanical properties shall be determined from separately cast test bars, and shall conform with the requirements. Brinell hardness readings shall be taken in the grip end of the tension test bar and shall be made in accordance with the specified requirements.
SCOPE
1.1 This specification covers requirements for copper alloy sand castings for valve applications. Nominal compositions of the alloys defined by this specification are shown in Table 1.2  
Note 1: This specification does not cover Copper Alloy UNS Nos. C83600, C92200, C96200, and C96400. These alloys are also used in valve applications. They are covered by the following specifications:
C83600: B62  
C92200: B61  
C96200: B369  
C96400: B369  
1.2 The castings produced under this specification are used in products which may be manufactured in advance and supplied for sale from stock by the manufacturer.  
1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM B950-23(Guide)
Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys

SIGNIFICANCE AND USE
4.1 The Form and Style for ASTM Standards manual provides mandatory requirements and recommended practices for the preparation and content of ASTM specifications. In order to promote consistency in the style and content of product specifications under its jurisdiction, Committee B05 recognizes the need to provide a supplementary document pertaining to the types of products and materials covered by specifications under its jurisdiction.  
4.2 This guide contains a list of sections to be considered for inclusion in a specification for copper and copper alloys, recommended wording, or both, for such sections. An electronic template including committee adopted language is included in the Appendix.7  
4.3 Persons drafting new product specifications, or modifying existing ones, under the jurisdiction of Committee B05, should follow this guide and the requirements of the Form and Style Manual to ensure consistency.
SCOPE
1.1 This guide covers the editorial procedures and form and style for product specifications under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys.
Note 1: For standards other than product specifications, such as test methods, practices, and guides, see the appropriate sections of Form and Style for ASTM Standards (Blue Book).2  
1.2 This guide has been prepared as a supplement to the current edition of the Form and Style Manual, and is appropriate for use by the subcommittees within ASTM Committee B05 on Copper and Copper Alloys. This guide is to be applied in conjunction with the Form and Style Manual. The Appendix contains a copy of the B05 electronic template which includes adopted language for various sections and provides a template for drafting B05 product specifications.
Note 2: The contents of this guide were previously maintained as a white paper under the title, “ASTM Committee B05 Outline of Form of Specifications.”  
1.3 Subcommittees preparing new product specifications or revising existing ones should follow the practices and procedures outlined herein, and be guided by the latest specifications covering similar commodities.  
1.4 If a conflict exists between this guide and the mandatory sections of the current edition of the Form and Style Manual, the Form and Style Manual requirements have precedence. If a conflict exists between this guide and the nonmandatory sections of the current edition of the Form and Style Manual, this guide has precedence.  
1.5 When patents are involved, the specifications writer should refer to the Form and Style Manual section on patents and trademarks. Also, refer to part F of the Form and Style Manual for trademark information and the safety hazards caveat.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    17 pages
    English language
    sale 15% off
  • Guide
    17 pages
    English language
    sale 15% off
ASTM
ASTM B103/B103M-23(Specification)
Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar

ABSTRACT
This specification covers plate, rolled bar, sheet, and strip of copper-tin alloy (phosphor bronze plate), copper-tin-lead alloy (leaded phosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze). Copper alloys covered include UNS Nos. C51000, C51100, C51180, C51900, C52100, C52180, C52400, C53400, and C54400. Product shall be manufactured by hot or cold working, rolling, and annealing. Chemical composition of the materials shall conform to UNS designation of the material. Product shall conform to chemical analysis, tensile strength and Rockwell hardness tests specified in the specification. Chemical composition testing shall be performed for each element, namely, copper, iron, lead, phosphorus, tin, and zinc. Tension test shall be made so that the longitudinal axis of the specimen is parallel to direction of rolling.
SCOPE
1.1 This specification covers the requirements for copper-tin alloy (phosphor bronze), copper-tin-lead alloy (leaded phosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze), plate, sheet, strip, and rolled bar for general application produced from Copper Alloy UNS Nos. C51000, C51100, C51180, C51900, C52100, C52180, C52400, C53400, and C54400. The phosphor bronzes commonly are used for deep drawing into bellows and stamping and forming into spring devices and into terminals and connectors for electrical apparatus because they combine high strength with high elongation. The leaded phosphor bronzes are used where strength, corrosion resistance, and machinability are required. The bearing bronze is used in bushings, bearings, and load-bearing thrust washers.
Note 1: All of the above alloys contain small amounts of phosphorus, used as a deoxidant in melting, and to enhance the mechanical properties.  
1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM B505/B505M-23(Specification)
Standard Specification for Copper Alloy Continuous Castings

ABSTRACT
This specification establishes requirements for continuously cast rod, bar, tube, and shapes produced from copper alloys with nominal compositions. Castings produced to this specification may be manufactured for and supplied from stock. Mechanical tests are required only when specified by the purchaser in the purchase order. Continuous castings shall not be mechanically repaired, plugged, or burned in. Weld repairs may be made at the manufacturer's discretion. For sampling purposes, a lot shall consist of castings of the same composition and same cross-sectional dimensions, produced during the continuous operation of one casting machine, and submitted for inspection at one time unless specified otherwise. The specimen shall be comprised of the following major elements: copper, tin, lead, zinc, iron, aluminum, manganese, and nickel including cobalt. Residual elements may be present in cast copper-base alloys. The fractured bars shall be retained for chemical verification. Both the Brinell hardness reading and Rockwell hardness reading shall be taken on the grip end of the tension test bar. At the request of the purchaser castings shall be marked with the alloy number.
SCOPE
1.1 This specification covers requirements for continuously cast rod, bar, tube, and shapes produced from copper alloys with nominal compositions as listed in Table 1.2  
1.2 Castings produced to this specification may be manufactured for and supplied from stock. In such cases the manufacturer shall maintain heat traceability to specific manufacturing date and chemical analysis.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    10 pages
    English language
    sale 15% off
  • Technical specification
    10 pages
    English language
    sale 15% off
ASTM
ASTM B806-23(Specification)
Standard Specification for Copper Alloy Permanent Mold Castings for General Applications

ABSTRACT
This specification covers the requirements for UNS C95300, C95400, C95410, C95500, C95800, C87500, C87800, C87850, and C89540 copper alloy permanent mold castings for general applications. UNS C95800 copper alloy used in sea water applications should be heat treated for better corrosion resistance. In general, alloys included in this specification are weldable. Mechanical properties like the tensile strength, yield strength and elongation are determined from separately cast test bar castings and should conform to the specified requirements.
SCOPE
1.1 This specification covers requirements for copper alloy2 permanent mold castings for general applications. Nominal compositions of the alloys under this specification are shown in Table 1.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM B249/B249M-23(Specification)
Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings

ABSTRACT
This specification establishes the general requirements common to wrought copper and copper alloy rods, bars, shapes, and forgings. Products shall be manufactured by hot working, cold working, or both, and finished by cold working, annealing, or heat treatment and straightening as identified necessary to meet the properties specified. Materials shall be sampled and prepared, then tested accordingly to examine their conformance to dimensional (mass, diameter, length, straightness, and edge contours), mechanical (tensile strength, Rockwell hardness, elongation, and hydrogen embrittlement), electrical resistivity, chemical composition, and grain size requirements. The products shall also meet performance requirements when subjected to residual stress, mercurous nitrate, ammonia vapor, and semiguided bend tests. In the event of conflict between this specification and the individual casting product specifications, the requirements of the casting specification shall take precedence.
SIGNIFICANCE AND USE
12.1 For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table and for dimensional tolerances, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.    
Property  
Rounded Unit for Observed or
Calculated Value  
Chemical composition  
Hardness  
nearest unit in the last right-hand  
Electrical resistivity  
significant digit used in expressing the  
Electrical conductivity  
limiting value  
Tensile strength  
nearest ksi [5 MPa]  
Yield strength  
Elongation:  
nearest 1 %  
Grain size:  
Under 0.060 mm  
nearest multiple of 0.005 mm  
0.060 mm and over  
nearest 0.01 mm
SCOPE
1.1 This specification2 covers the general requirements common to wrought copper and copper alloy rod, bar, shapes, and forgings which shall apply to Specifications B16/B16M, B21/B21M, B98/B98M, B124/B124M, B138/B138M, B139/B139M, B140/B140M, B150/B150M, B151/B151M, B187/B187M, B196/B196M, B283/B283M, B301/B301M, B371/B371M, B411/B411M, B441, B453/B453M, B455, B570, B870, B927/B927M, B929, B967/B967M, B974/B974M, and B981/B981M to the extent referenced therein.  
1.2 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification are prescribed in the product specification.  
1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3.1 Within the text the SI values are given in brackets.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    13 pages
    English language
    sale 15% off
  • Technical specification
    13 pages
    English language
    sale 15% off
ASTM
ASTM B927/B927M-23(Specification)
Standard Specification for Brass Rod, Bar, and Shapes

ABSTRACT
This specification establishes requirements for brass rod (round, hexagonal, and octagonal), bar (rectangular and square), and shapes of UNS Alloys C21000, C22000, C23000, C24000, C26000, C26800, C27000, and C27400. The material shall be made from cast billets, logs, or rods of copper alloy, as determined by chemical analysis. The products shall be manufactured by such hot working, cold working, and annealing processing as to produce a uniform wrought structure. The material shall conform to the chemical compositional requirements prescribed for copper, lead, iron, and zinc. The standard tempers, either hard or soft anneal (namely: O60, H01, H02, and H04), for rod and bar are specified. Tensile requirements to which the product shall conform includes tensile strength, yield strength, and elongation. The dimensional requirements for rods, bars, and shapes are given.
SCOPE
1.1 This specification establishes requirements for brass rod (round, hexagonal, and octagonal), bar (rectangular and square), and shapes of UNS Alloys C21000, C22000, C23000, C24000, C26000, C26800, C27000, C27400, C27450, C27451, C27453, C27550, and C28500.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM B271/B271M-23(Specification)
Standard Specification for Copper-Base Alloy Centrifugal Castings

ABSTRACT
This specification establishes the requirements for copper-based brass or bronze centrifugal castings. Mechanical properties are determined from test bar castings and should meet the requirements listed herein. Brinell hardness readings should be taken on the grip end of tension test bars. All castings should not be repaired by welding without customer approval. UNS C95520 copper alloy castings are used in the heat treated condition only.
SCOPE
1.1 This specification covers requirements for centrifugal castings of copper-base alloys having the nominal compositions shown in Table 1.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off