ASTM B470-02(2012)
(Specification)Standard Specification for Bonded Copper Conductors for Use in Hookup Wires for Electronic Equipment
Standard Specification for Bonded Copper Conductors for Use in Hookup Wires for Electronic Equipment
ABSTRACT
This specification covers stranded uninsulated bare, tin, or tin-lead alloy coated copper conductors in which wires in the strand are metallically bonded together by the application of heat additional tin, or tin-lead alloy for use in hookup wire for electronic equipment. Conductor constructions shall conform to standard ASTM requirements except that, in addition, the following bondings may be specified: Type I, Type II, and Type III. The conductors shall consist of tinned copper and bare copper, conforming to product description, quality, and specification requirements. The material shall undergo flex, fraying, mandrel, and resistance tests. The material shall meet the minimum flex life requirements and shall conform to the required conditions for flex, fraying, and madrel tests.
SCOPE
1.1 This specification covers stranded uninsulated bare, tin, or tin-lead alloy coated copper conductors in which wires in the strand are metallically bonded together by the application of heat or additional tin, or tin-lead alloy for use in hookup wire for electronic equipment.
1.2 The SI values for density and resistivity are to be regarded as standard. For all other properties, the inch-pound values are to be regarded as the standard and the SI units may be approximate.
1.3 The hazard caveat pertains only to Section 6 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B470 −02 (Reapproved 2012)
Standard Specification for
Bonded Copper Conductors for Use in Hookup Wires for
1
Electronic Equipment
This standard is issued under the fixed designation B470; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.1.3 Special package marking if required (Section 8), and
3.1.4 Place of inspection (Section 7).
1.1 This specification covers stranded uninsulated bare, tin,
ortin-leadalloycoatedcopperconductorsinwhichwiresinthe
4. Conductor Constructions
strand are metallically bonded together by the application of
4.1 Conductor constructions shall conform to the applicable
heat or additional tin, or tin-lead alloy for use in hookup wire
for electronic equipment. constructions of Specification B286, except that in addition the
following bondings may be specified:
1.2 The SI values for density and resistivity are to be
4.1.1 Type I—Bare copper, stranded, light bonding,
regarded as standard. For all other properties, the inch-pound
4.1.2 Type II—Tin or tin-lead alloy coated copper, stranded,
values are to be regarded as the standard and the SI units may
light bonding, or
be approximate.
4.1.3 TypeIII—Tinortin-leadalloycoatedcopper,stranded,
1.3 The hazard caveat pertains only to Section 6 of this
heavy bonding.
specification. This standard does not purport to address all of
the safety concerns, if any, associated with its use. It is the
5. General Requirements
responsibility of the user of this standard to establish appro-
5.1 The conductors shall consist of tinned copper conform-
priate safety and health practices and determine the applica-
ing to the product description, quality and specification re-
bility of regulatory limitations prior to use.
quirements of Specification B286 and bare copper conforming
to the product description, quality and specification require-
2. Referenced Documents
ments of Specification B3.
2.1 The following documents of the issue in effect at the
5.2 Flex Life—The average of six flex tests specified in 6.1
time of reference form a part of this specification to the extent
shall meet the minimum requirements of Table 1 for the
referenced herein:
applicable type and construction.
2
2.2 ASTM Standards:
5.3 Fraying, Types I and II—After performing the test in
B3 Specification for Soft or Annealed Copper Wire
6.2,noseparationsofstrandsshallbevisibletotheunaidedeye
B286 Specification for Copper Conductors for Use in
(normal spectacles excepted), from the cut end to the point of
Hookup Wire for Electronic Equipment
bend nearest to that cut end.
3. Ordering Information
5.4 Mandrel Test, Type III Only (see Explanatory Note
3.1 Orders for material under this specification shall include
1)—After performing the test specified in 6.3 no separation of
the following information:
strands shall be visible to the unaided eye (normal spectacles
3.1.1 Quantity of each size, material, construction, and type
excepted).
(see 4.1),
3.1.2 Package size (see 8.1),
6. Test Methods
6.1 Flex Life—The testing equipment shall be designed and
1
This specification is under the jurisdiction of ASTM Committee B01 on
set up for operation so that steel mandrels shall be horizontal
Electrical Conductors and is the direct responsibility of Subcommittee B01.04 on
and so positioned that any vertical movement of the specimen
Conductors of Copper and Copper Alloys.
is minimized. The conductor as clamped for test shall pass
Current edition approved Oct. 15, 2012. Published November 2012. Originally
through the vertical center line between the mandrels.
approved in 1968. Last previous edition approved in 2007 as B470 – 02 (2007).
DOI: 10.1520/B0470-02R12.
6.1.1 The conductor shall be bent repeatedly in alternating
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
directions in an arc of 60° on both sides of the vertical center
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
line of the mandrels, at a rate of 24 to 36 cpm, between
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. mandrels of size and spacing specified in Table 2. The
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B470−02 (2012)
TABLE 1 Flex Life Requirements, Minimum Cycles
7. Inspection
Un-
Type I
7.1 General—All test and inspections shall be made at the
bonded Type III
and II
place of manufacture unless otherwise agreed upon between
Construction (see (Heavy
(Light
Explanatory Bonding)
the manufacturer and
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.