ASTM B465-03
(Specification)Standard Specification for Copper-Iron Alloy Plate, Sheet, Strip, and Rolled Bar
Standard Specification for Copper-Iron Alloy Plate, Sheet, Strip, and Rolled Bar
SCOPE
1.1 This specification establishes Copper Alloy UNS Nos. C19200, C19210, C19400, C19500, and C19700 plate, sheet, strip, and rolled bar.
1.2 The values stated in inch-pound units are to be regarded as the standard.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B 465 – 03
Standard Specification for
1
Copper-Iron Alloy Plate, Sheet, Strip, and Rolled Bar
This standard is issued under the fixed designation B 465; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* 3.1.1 Terminology,
3.1.2 Materials and Manufacture,
1.1 This specification establishes Copper Alloy UNS Nos.
3.1.3 Workmanship, Finish, and Appearance,
C19200, C19210, C19400, C19500, and C19700 plate, sheet,
3.1.4 Sampling,
strip, and rolled bar.
3.1.5 Number of Tests and Retests,
1.2 The values stated in inch-pound units are to be regarded
3.1.6 Specimen Preparation,
as the standard.
3.1.7 Test Methods (except chemical analysis),
2. Referenced Documents 3.1.8 Significance of Numerical Limits,
2
3.1.9 Inspection,
2.1 ASTM Standards:
3.1.10 Rejection and Rehearing,
B 193 Test Method for Resistivity of Electrical Conductor
3.1.11 Certification,
Materials
3.1.12 Test Reports (Mill),
B 248 Specification for General Requirements for Wrought
3.1.13 Packaging and Package Marking, and
Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled
3.1.14 Supplementary Requirements.
Bar
3.2 In addition, when a section with a title identical to that
B 601 Classification for Temper Designations for Copper
referenced in 3.1 appears in this specification, it contains
and Copper Alloys—Wrought and Cast
additional requirements which supplement those appearing in
B 846 Terminology for Copper and Copper Alloys
Specification B 248.
E 8 Test Methods for Tension Testing of Metallic Materials
E 54 Test Methods for Chemical Analysis of Special
4. Terminology
Brasses and Bronzes
4.1 Definitions—For definitions of terms related to copper
E 62 Test Methods for Chemical Analysis of Copper and
and copper alloys, refer to Terminology B 846.
Copper Alloys (Photometric Methods)
E 75 Test Methods for Chemical Analysis of Copper-Nickel
5. Ordering Information
and Copper-Nickel-Zinc Alloys
5.1 Contracts or purchase orders for product under this
E 76 Test Methods for Chemical Analysis of Nickel-Copper
specification should include the following information:
Alloys
5.1.1 ASTM designation and year of issue (for example
E 112 Test Methods for Determining Average Grain Size
B 465–XX),
E 478 Test Methods for Chemical Analysis of Copper
5.1.2 Copper Alloy UNS No. designation (for example,
Alloys
C19200),
E 527 Practice for Numbering Metals and Alloys (UNS)
5.1.3 Temper (Section 8),
3. General Requirements 5.1.4 Dimensions—Thickness, width, length, and so forth
(Section 13),
3.1 The following sections of Specification B 248 consti-
5.1.5 Form—Plate, sheet, strip, or rolled bar,
tutes a part of this specification:
5.1.6 How Furnished—Coils (rolls), specific lengths or
stock lengths, with or without ends,
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper
5.1.7 Quantity—total weight each form, temper, and size,
and Copper Alloys and is the direct responsibility of Subcommittee B05.1 on Plate,
and
Sheet, and Strip.
5.1.8 When material is purchased for agencies of the U.S.
Current edition approved Oct. 1, 2003. Published November 2003. Originally
approved in 1968. Last previous edition approved in 2000 as B 465 – 00.
government (Section 12).
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
5.2 The following options are available under this specifi-
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
cation and should be specified in the contract or purchase order
Standards volume information, refer to the standard’s Document Summary page on
when required:
the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B465–03
5.2.1 Type of Edge—Slit, sheared, sawed, square corners, 8. Temper
round corners, rounded edges, or full rounded edges,
8.1 As defined in Classification B 601, products shall be
5.2.2 Width and straightness tolerances (appropriate table in
produced in tempers O60 (soft annealed), O61 (annealed), O50
Specification B 248), 1 1
(light annealed), O82 (annealed to temper - ⁄2 hard), H01 ( ⁄4
5.2.3 Heat identification or traceability details,
1 3
hard), H02 ( ⁄2 hard), H03 ( ⁄4 hard), H04 (hard), H06 (extra
5.2.4 Certification, and
hard), H08 (spring), H10 (extra spring), and H14 (super
5.2.5 Mill test report.
spring).
6. Materials and Manufacture
NOTE 2—The purchaser should confer with
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.