ASTM B465-00e1
(Specification)Standard Specification for Copper-Iron Alloy Plate, Sheet, Strip, and Rolled Bar
Standard Specification for Copper-Iron Alloy Plate, Sheet, Strip, and Rolled Bar
SCOPE
1.1 This specification covers Copper Alloy UNS Nos. C19200, C19400, C19500, and C19700 plate, sheet, strip, and rolled bar.
1.2 The values stated in inch-pound units are to be regarded as the standard.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
e1
Designation: B 465 – 00
Standard Specification for
1
Copper-Iron Alloy Plate, Sheet, Strip, and Rolled Bar
This standard is issued under the fixed designation B 465; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
e NOTE—Section 1.1, Summary of Changes, Table 1, and Table 4 were editorially corrected in October 2001.
1. Scope * 3. Terminology
1.1 This specification establishes Copper Alloy UNS Nos. 3.1 Definitions—For definitions of terms related to copper
2
C19200, C19400, C19500, and C19700 plate, sheet, strip, and and copper alloys, refer to Terminology B 846.
rolled bar.
4. General Requirements
1.2 The values stated in inch-pound units are to be regarded
4.1 The following sections of Specification B 248 consti-
as the standard.
tutes a part of this specification:
2. Referenced Documents
4.1.1 Terminology,
2.1 ASTM Standards: 4.1.2 Materials and Manufacture,
B 193 Test Method for Resistivity of Electrical Conductor 4.1.3 Workmanship, Finish, and Appearance,
2
Materials 4.1.4 Sampling,
B 248 Specification for General Requirements for Wrought 4.1.5 Number of Tests and Retests,
Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled 4.1.6 Specimen Preparation,
3
Bar 4.1.7 Test Methods (except chemical analysis),
B 601 Practice for Temper Designations for Copper and 4.1.8 Significance of Numerical Limits,
3
Copper Alloys—Wrought and Cast 4.1.9 Inspection,
3
B 846 Terminology for Copper and Copper Alloys 4.1.10 Rejection and Rehearing,
4
E 8 Test Methods for Tension Testing of Metallic Materials 4.1.11 Certification,
E 54 Test Methods for Chemical Analysis of Special 4.1.12 Test Reports (Mill),
5
Brasses and Bronzes 4.1.13 Packaging and Package Marking, and
E 62 Test Methods for Chemical Analysis of Copper and 4.1.14 Supplementary Requirements.
5
Copper Alloys (Photometric Methods) 4.2 In addition, when a section with a title identical to that
E 75 Test Methods for Chemical Analysis of Copper-Nickel referenced in 4.1 appears in this specification, it contains
5
and Copper-Nickel-Zinc Alloys additional requirements which supplement those appearing in
E 76 Test Methods for Chemical Analysis of Nickel-Copper Specification B 248.
5
Alloys
4 5. Ordering Information
E 112 Test Methods for Determining Average Grain Size
5.1 Contracts or purchase orders for product under this
E 478 Test Methods for Chemical Analysis of Copper
6
Alloys specification should include the following information:
4
5.1.1 ASTM designation and year of issue (for example
E 527 Practice for Numbering Metals and Alloys (UNS)
B 465–XX),
5.1.2 Copper Alloy UNS No. designation (for example,
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper
C19200),
and Copper Alloys and is the direct responsibility of Subcommittee B05.1 on Plate,
5.1.3 Temper (Section 8),
Sheet, and Strip.
5.1.4 Dimensions—Thickness, width, length, and so forth
Current edition approved May 10, 2000. Published July 2000. Originally
published as B 465 – 68. Last previous edition B 465 – 93.
(Section 11),
2
Annual Book of ASTM Standards, Vol 02.03.
5.1.5 Form—Plate, sheet, strip, or rolled bar,
3
Annual Book of ASTM Standards, Vol 02.01.
4 5.1.6 How Furnished—Coils (rolls), specific lengths or
Annual Book of ASTM Standards, Vol 03.01.
5
Annual Book of ASTM Standards, Vol 03.05. stock lengths, with or without ends,
6
Annual Book of ASTM Standards, Vol 03.06.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
e1
B465–00
5.1.7 Quantity—total weight each form, temper, and size, required for unnamed elements by agreement between the
and manufacturer and the purchaser.
5.1.8 When material is purchased for agencies of the U.S. 7.2 Copper, when specified as the remainder, may be taken
Government (Section 11). as the difference between the sum of results for specified
5.2 The following options are available under this specifi- elements and 100 %.
cation and should be specified in the contract or purchase order 7.3 When all elements listed in Table 1 for the designated
when required: alloy are determined, the sum of results shall be 99.8 %
5.2.1 Type of Edge—Slit, sheared, sawed, square corners, minimum.
round corners, rounded ed
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.