ASTM D1718-09(2017)
(Specification)Standard Specification for Isobutyl Acetate (95 % Grade)
Standard Specification for Isobutyl Acetate (95 % Grade)
ABSTRACT
This specification details the properties and requirements for isobutyl acetate. The specimens shall be sampled, go through chemical tests and conform accordingly to specified values of the following requirements: apparent specific gravity; color (Pt-Co units) distillation (initial boiling point and dry point); nonvolatile matter content; water content; acidity (free acid as acetic acid); and purity.
SCOPE
1.1 This specification covers isobutyl acetate (95 % grade).
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 For specific hazard information and guidance, see the supplier’s Safety Data Sheet for material listed in this specification.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D1718 − 09 (Reapproved 2017)
Standard Specification for
Isobutyl Acetate (95 % Grade)
This standard is issued under the fixed designation D1718; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope D1209 Test Method for Color of Clear Liquids (Platinum-
Cobalt Scale)
1.1 This specification covers isobutyl acetate (95 % grade).
D1353 Test Method for Nonvolatile Matter in Volatile Sol-
1.2 The following applies to all specified limits in this
vents for Use in Paint, Varnish, Lacquer, and Related
standard; for purposes of determining conformance with this
Products
standard, an observed value or a calculated value shall be
D1364 Test Method for Water in Volatile Solvents (Karl
rounded off “to the nearest unit” in the last right-hand digit
Fischer Reagent Titration Method)
used in expressing the specification limit, in accordance with
D1476 Test Method for Heptane Miscibility of Lacquer
the rounding-off method of Practice E29.
Solvents
1.3 The values stated in SI units are to be regarded as D1613 Test Method for Acidity in Volatile Solvents and
Chemical Intermediates Used in Paint, Varnish, Lacquer,
standard. No other units of measurement are included in this
standard. and Related Products
D3545 Test Method for Alcohol Content and Purity of
1.4 For specific hazard information and guidance, see the
Acetate Esters by Gas Chromatography
supplier’s Safety Data Sheet for material listed in this specifi-
D4052 Test Method for Density, Relative Density, and API
cation.
Gravity of Liquids by Digital Density Meter
1.5 This international standard was developed in accor-
D5386 Test Method for Color of Liquids Using Tristimulus
dance with internationally recognized principles on standard-
Colorimetry
ization established in the Decision on Principles for the
E29 Practice for Using Significant Digits in Test Data to
Development of International Standards, Guides and Recom-
Determine Conformance with Specifications
mendations issued by the World Trade Organization Technical
E300 Practice for Sampling Industrial Chemicals
Barriers to Trade (TBT) Committee. 3
2.2 U.S. Federal Specification:
PPP-C-2020 Chemicals, Liquid, Dry, and Paste: Packaging
2. Referenced Documents
of
2.1 ASTM Standards:
D268 Guide for Sampling and Testing Volatile Solvents and 3. Properties
Chemical Intermediates for Use in Paint and Related
3.1 Isobutyl acetate shall conform to the following require-
Coatings and Material 4
ments:
D1078 Test Method for Distillation Range of Volatile Or-
ganic Liquids
This specification is under the jurisdiction of ASTM Committee D01 on Paint
and Related Coatings, Materials, and Applications and is the direct responsibility of
Subcommittee D01.35 on Solvents, Plasticizers, and Chemical Intermediates.
Current edition approved Dec. 1, 2017. Published December 2017. Originally
approved in 1960. Last previous edition approved in 2009 as D1718 – 09. DOI:
10.1520/D1718-09R17. Available from DLA Document Services, Building 4/D, 700 Robbins Ave.,
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Philadelphia, PA 19111-5094, http://quicksearch.dla.mil.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM In some c
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D1718 − 09 D1718 − 09 (Reapproved 2017)
Standard Specification for
Isobutyl Acetate (95 % Grade)
This standard is issued under the fixed designation D1718; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*Scope
1.1 This specification covers isobutyl acetate (95 % grade).
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard,
an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing
the specification limit, in accordance with the rounding-off method of Practice E29.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 For specific hazard information and guidance, see the supplier’s Material supplier’s Safety Data Sheet for material listed in
this specification.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 ASTM Standards:
D268 Guide for Sampling and Testing Volatile Solvents and Chemical Intermediates for Use in Paint and Related Coatings and
Material
D1078 Test Method for Distillation Range of Volatile Organic Liquids
This specification is under the jurisdiction of ASTM Committee D01 on Paint and Related Coatings, Materials, and Applications and is the direct responsibility of
Subcommittee D01.35 on Solvents, Plasticizers, and Chemical Intermediates.
Current edition approved Dec. 1, 2009Dec. 1, 2017. Published January 2010December 2017. Originally approved in 1960. Last previous edition approved in 20032009
as D1718 – 03.D1718 – 09. DOI: 10.1520/D1718-09.10.1520/D1718-09R17.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D1718 − 09 (2017)
D1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
D1353 Test Method for Nonvolatile Matter in Volatile Solvents for Use in Paint, Varnish, Lacquer, and Related Products
D1364 Test Method for Water in Volatile Solvents (Karl Fischer Reagent Titration Method)
D1476 Test Method for Heptane Miscibility of Lacquer Solvents
D1613 Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related
Products
D3545 Test Method for Alcohol Content and Purity of Acetate Esters by Gas Chromatography
D4052 Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
D5386 Test Method for Color of Liquids Using Tristimulus Colorimetry
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E300 Practice for Sampling Industrial Chemicals
2.2 U.S. Federal Specification:
PPP-C-2020 Chemicals, Liquid, Dry, and Paste:
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.