ASTM F758-14
(Specification)Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Plastic Underdrain Systems for Highway, Airport, and Similar Drainage
Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Plastic Underdrain Systems for Highway, Airport, and Similar Drainage
ABSTRACT
This specification covers the requirements for smooth-wall perforated and nonperforated poly(vinyl chloride) (PVC) plastic pipe and couplings for use in subsurface drainage systems of highways, airports, and similar applications. Two classes (or pipe stiffness) are included and designated as PS 28 and PS 46. The pipe stiffness, impact resistance, pipe flattening, and solvent cement joint tightness shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers the requirements for smooth-wall perforated and nonperforated poly(vinyl chloride) (PVC) plastic pipe and couplings for use in subsurface drainage systems of highways, airports, and similar applications in nominal sizes of 4, 6, and 8 in. and in pipe stiffnesses (PS) that are designated as Type PS 28 and Type PS 46 in accordance with its minimum pipe stiffness.
1.2 Molded fittings for use with highway underdrain pipe are in accordance with Specification D3034. For convenience, some of these fittings are reproduced in Annex A1.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
Note 1: Type PS 28 and Type PS 46 indicate “pipe stiffness” of 28 and 46, respectively, as outlined in 11.1.
Note 2: Pipe and fittings should be installed in accordance with Practice D2321, or applicable state or local specifications.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F758 −14
Standard Specification for
Smooth-Wall Poly(Vinyl Chloride) (PVC) Plastic Underdrain
1
Systems for Highway, Airport, and Similar Drainage
ThisstandardisissuedunderthefixeddesignationF758;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)
Compounds and Chlorinated Poly(Vinyl Chloride)
1.1 This specification covers the requirements for smooth-
(CPVC) Compounds
wall perforated and nonperforated poly(vinyl chloride) (PVC)
D2122 Test Method for Determining Dimensions of Ther-
plastic pipe and couplings for use in subsurface drainage
moplastic Pipe and Fittings
systems of highways, airports, and similar applications in
D2152 Test Method for Adequacy of Fusion of Extruded
nominal sizes of 4, 6, and 8 in. and in pipe stiffnesses (PS) that
Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by
are designated as Type PS 28 and Type PS 46 in accordance
Acetone Immersion
with its minimum pipe stiffness.
D2321 PracticeforUndergroundInstallationofThermoplas-
1.2 Molded fittings for use with highway underdrain pipe
tic Pipe for Sewers and Other Gravity-Flow Applications
are in accordance with Specification D3034. For convenience,
D2412 Test Method for Determination of External Loading
some of these fittings are reproduced in Annex A1.
Characteristics of Plastic Pipe by Parallel-Plate Loading
1.3 The values stated in inch-pound units are to be regarded
D2444 Test Method for Determination of the Impact Resis-
as the standard. The values given in parentheses are for tance of Thermoplastic Pipe and Fittings by Means of a
information only.
Tup (Falling Weight)
D2564 Specification for Solvent Cements for Poly(Vinyl
NOTE1—TypePS28andTypePS46indicate“pipestiffness”of28and
Chloride) (PVC) Plastic Piping Systems
46, respectively, as outlined in 11.1.
NOTE 2—Pipe and fittings should be installed in accordance with D2855 Practice for Making Solvent-Cemented Joints with
Practice D2321, or applicable state or local specifications.
Poly(Vinyl Chloride) (PVC) Pipe and Fittings
1.4 The following safety hazards caveat pertains only to the
D3034 Specification for Type PSM Poly(Vinyl Chloride)
test methods portion, Section 11, of this specification:This (PVC) Sewer Pipe and Fittings
standard does not purport to address all of the safety concerns,
D3212 Specification for Joints for Drain and Sewer Plastic
if any, associated with its use. It is the responsibility of the user
Pipes Using Flexible Elastomeric Seals
of this standard to establish appropriate safety and health
D4396 Specification for Rigid Poly(Vinyl Chloride) (PVC)
practices and determine the applicability of regulatory limita-
and Chlorinated Poly(Vinyl Chloride) (CPVC) Com-
tions prior to use.
pounds for Plastic Pipe and Fittings Used in Nonpressure
3
Applications (Withdrawn 2015)
2. Referenced Documents
F402 Practice for Safe Handling of Solvent Cements,
2
2.1 ASTM Standards:
Primers, and Cleaners Used for Joining Thermoplastic
D618 Practice for Conditioning Plastics for Testing Pipe and Fittings
D1600 Terminology forAbbreviatedTerms Relating to Plas-
F412 Terminology Relating to Plastic Piping Systems
tics
2.2 Federal Standard:
4
Fed. Std. No. 123 Marking for Shipments (Civil Agencies)
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
2.3 Military Standard:
Piping Systems and is the direct responsibility of Subcommittee F17.65 on Land
4
MIL-STD-129 Marking for Shipment and Storage
Drainage.
Current edition approved Nov. 1, 2014. Published December 2014. Originally
ε1
approved in 1982. Last previous edition approved in 2007 as F758 – 95(2007) .
DOI: 10.1520/F0758-14.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or The last approved version of this historical standard is referenced on
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM www.astm.org.
4
Standards volume information, refer to the standard’s Document Summary page on DLA Document Services Building 4/D 700 Robbins Avenue Philadelphia, PA
the ASTM website. 19111-5094 http://quicksearch.dla.mil/.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F758−14
TABLE 2 Dimensions of Bends
3. Terminology
3.1 Definitions—Definitions are in accordance with Termi-
nology F412, and abbreviations are in accordance with
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: F758 − 95 (Reapproved 2007) F758 − 14 An American National Standard
Standard Specification for
Smooth-Wall Poly(Vinyl Chloride) (PVC) Plastic Underdrain
1
Systems for Highway, Airport, and Similar Drainage
This standard is issued under the fixed designation F758; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1
ε NOTE—Section 7.2.8.1 was editorially corrected in February 2007.
1. Scope Scope*
1.1 This specification covers the requirements for smooth-wall perforated and nonperforated poly(vinyl chloride) (PVC) plastic
pipe and couplings for use in subsurface drainage systems of highways, airports, and similar applications in nominal sizes of 4,
6, and 8 in. and in pipe stiffnesses (PS) that are designated as Type PS 28 and Type PS 46 in accordance with its minimum pipe
stiffness.
1.2 Molded fittings for use with highway underdrain pipe are in accordance with Specification D3034. For convenience, some
of these fittings are reproduced in Annex A1.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
NOTE 1—Type PS 28 and Type PS 46 indicate “pipe stiffness” of 28 and 46, respectively, as outlined in 11.1.
NOTE 2—Pipe and fittings should be installed in accordance with Practice D2321, or applicable state or local specifications.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 1111,, of this specification: This
standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior
to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2152 Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone
Immersion
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling
Weight)
D2564 Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
D2855 Practice for Making Solvent-Cemented Joints with Poly(Vinyl Chloride) (PVC) Pipe and Fittings
D3034 Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings
D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.65 on Land Drainage.
Current edition approved Feb. 1, 2007Nov. 1, 2014. Published February 2007December 2014. Originally approved in 1982. Last previous edition approved in 20002007
ε1
as F758 – 95(2000).(2007) . DOI: 10.1520/F0758-95R07E01.10.1520/F0758-14.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F758 − 14
D4396 Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for
Plastic Pipe and Fittings Used in Nonpressure Applications
F402 Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings
F412 Terminology Relating to Plastic Piping Systems
2.2 Feder
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.