ASTM A323-05(2015)
(Specification)Standard Specification for Ferroboron
Standard Specification for Ferroboron
ABSTRACT
This specification covers several grades of ferroboron. The grades shall conform to the required chemical composition for boron, carbon, silicon, and aluminum. Various sizes of ferroboron are detailed. Chemical analysis of the material shall be made.
SCOPE
1.1 This specification covers several grades of ferroboron.
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A323 −05 (Reapproved 2015)
Standard Specification for
Ferroboron
This standard is issued under the fixed designation A323; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope mentary requirements that are indicated in the purchase order.
Failure to comply with the general requirements of Specifica-
1.1 This specification covers several grades of ferroboron.
tion A1025 constitutes nonconformance with this specification.
1.2 The values stated in inch-pound units are to be regarded
In case of conflict between the requirements of this specifica-
as the standard. The SI units given in parentheses are for
tion and Specification A1025, this specification shall prevail.
information only.
4. Chemical Composition
2. Referenced Documents
4.1 The various grades shall conform to the requirements as
2.1 ASTM Standards:
to chemical composition specified in Table 1. The manufac-
A1025 Specification for Ferroalloys and Other Alloying
turer shall furnish an analysis of each lot showing the percent-
Materials, General Requirements
age of each element specified.
E371 Test Method for The Determination of Boron in
Ferroboron (Withdrawn 2006)
5. Sizing
5.1 Ferroboron is available in various sizes such as: 2 in.
3. General Conditions for Delivery
(50.8mm)bydown,1in.(25.4mm)bydown, ⁄4in.(6.35mm)
3.1 Materials furnished to this specification shall conform to
by down, and 20 mesh (0.841 mm) by down. The size shall be
therequirementsofSpecificationA1025,includinganysupple-
as specified in the order.
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
6. Chemical Analysis
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
6.1 The chemical analysis of the material shall be made in
A01.18 on Castings.
Current edition approved Nov. 1, 2015. Published November 2015. Originally
accordance with Test Method E371. Where a method is not
approved in 1949. Last previous edition approved in 2010 as A323 – 05 (2010).
given in Test Method E371 for the analysis for a particular
DOI: 10.1520/A0323-05R15.
2 element, the anal
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A323 − 05 (Reapproved 2010) A323 − 05 (Reapproved 2015)
Standard Specification for
Ferroboron
This standard is issued under the fixed designation A323; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers several grades of ferroboron.
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for
information only.
2. Referenced Documents
2.1 ASTM Standards:
A1025 Specification for Ferroalloys and Other Alloying Materials, General Requirements
E371 Test Method for The Determination of Boron in Ferroboron (Withdrawn 2006)
3. General Conditions for Delivery
3.1 Materials furnished to this specification shall conform to the requirements of Specification A1025, including any
supplementary requirements that are indicated in the purchase order. Failure to comply with the general requirements of
Specification A1025 constitutes nonconformance with this specification. In case of conflict between the requirements of this
specification and Specification A1025, this specification shall prevail.
4. Chemical Composition
4.1 The various grades shall conform to the requirements as to chemical composition specified in Table 1. The manufacturer
shall furnish an analysis of each lot showing the percentage of each element specified.
5. Sizing
5.1 Ferroboron is available in various sizes such as: 2 in. (50.8 mm) by down, 1 in. (25.4 mm) by down, ⁄4 in. (6.35 mm) by
down, and 20 mesh (0.841 mm) by down. The size shall be as specified in the order.
6. Chemical Analysis
6.1 The chemical analysis of the material shall be made in accordance with Test Method E371. Where a method is not given
in Test Method E371 for the analysis for a particular element, the analysis shall be made in accordance with a procedure agreed
upon by the manufacturer and purchaser.
7. Keywords
7.1 ferroboron
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.