iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3567-97(2006)

(Practice)

Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings

Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings

SIGNIFICANCE AND USE
This practice provides for determining the physical dimensions of fiberglass pipe and fittings. This practice is suitable for determination of dimensional compliance with product specifications.
SCOPE
1.1 This practice covers the determination of outside diameter, inside diameter, total wall thickness, reinforced wall thickness, liner thickness (where applicable), and length dimensions of "fiberglass" (glass-fiber-reinforced thermosetting resin) pipe. Included are procedures for measuring tapered dimensions and taper angles for pipe intended to be joined by tapered socket fittings, and procedures for gaging internal and external threads.
1.2 This practice also includes procedures for determining dimensions for fiberglass pipe fittings.
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.Note 1
There is no similar or equivalent ISO standard.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
14-Oct-2006
ICS
23.040.20 - Plastics pipes
23.040.45 - Plastics fittings
Technical Committee
D20 - Plastics
Drafting Committee
D20.23 - Reinforced Thermosetting Resin Piping Systems and Chemical Equipment
Current Stage
Ref Project

Relations

Replaces
ASTM D3567-97(2002) - Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
Effective Date
15-Oct-2006
Replaced By
ASTM D3567-97(2011) - Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
Effective Date
01-Dec-2011
Referred By
ASTM D3754-19 - Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe
Effective Date
15-Oct-2006
Referred By
ASTM D1599-18 - Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
Effective Date
15-Oct-2006
Referred By
ASTM D2992-22 - Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
Effective Date
15-Oct-2006
Referred By
ASTM F2019-22 - Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic Cured-in-Place (GRP-CIPP) Using the UV-Light Curing Method
Effective Date
15-Oct-2006
Referred By
ASTM D2105-01(2019) - Standard Test Method for Longitudinal Tensile Properties of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube
Effective Date
15-Oct-2006
Referred By
ASTM D2143-21 - Standard Test Method for Cyclic Pressure Strength of Reinforced, Thermosetting Plastic Pipe
Effective Date
15-Oct-2006
Referred By
ASTM D1598-23 - Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
Effective Date
15-Oct-2006
Referred By
ASTM D5677-17 - Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings, Adhesive Bonded Joint Type, for Aviation Jet Turbine Fuel Lines
Effective Date
15-Oct-2006
Referred By
ASTM D5685-19 - Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings
Effective Date
15-Oct-2006
Referred By
ASTM D3262-20 - Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer Pipe
Effective Date
15-Oct-2006
Referred By
ASTM D3681-23 - Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition
Effective Date
15-Oct-2006
Referred By
ASTM D3840-19 - Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Fittings for Nonpressure Applications
Effective Date
15-Oct-2006
Referred By
ASTM D6783-05a(2022) - Standard Specification for Polymer Concrete Pipe
Effective Date
15-Oct-2006

Buy Standard

ASTM D3567-97(2006) - Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and FittingsASTM D3567-97(2006) - Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
PreviousNext
Standard
ASTM D3567-97(2006) - Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation:D3567–97 (Reapproved 2006)
Standard Practice for
Determining Dimensions of “Fiberglass” (Glass-Fiber-
1
Reinforced Thermosetting Resin) Pipe and Fittings
This standard is issued under the fixed designation D3567; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
4
1. Scope* B2.1 Pipe Threads (Except Dryseal)
2.3 API Standard:
1.1 This practice covers the determination of outside diam-
API5B Threading, Gaging, and Thread Inspection of Cas-
eter, inside diameter, total wall thickness, reinforced wall
5
ing, Tubing, and Line Pipe Threads
thickness, liner thickness (where applicable), and length di-
mensions of “fiberglass” (glass-fiber-reinforced thermosetting
3. Terminology
resin) pipe. Included are procedures for measuring tapered
3.1 Definitions of Terms Specific to This Standard:
dimensions and taper angles for pipe intended to be joined by
3.1.1 deviation from straightness— the maximum deviation
tapered socket fittings, and procedures for gaging internal and
fromastraightlineexhibitedbyapipespecimendividedbythe
external threads.
length of the specimen.
1.2 This practice also includes procedures for determining
3.1.2 fiberglass pipe—a tubular product containing glass-
dimensions for fiberglass pipe fittings.
fiber reinforcements embedded in or surrounded by cured
1.3 The values stated in inch-pound units are to be regarded
thermosetting resin; the composite structure may contain
as the standard. The SI units given in parentheses are for
aggregate, granular, or platelet fillers, thixotropic agents, pig-
information only.
ments, or dyes; thermoplastic or thermosetting liners or coat-
NOTE 1—There is no similar or equivalent ISO standard.
ings may be included.
3.1.3 laying length of fittings—the actual increase in the
1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the length of a line afforded by the fitting when installed.
responsibility of whoever uses this standard to consult and 3.1.4 liner and exterior surface layer thicknesses—theinner
and outer portions of the wall used to enhance chemical and
establish appropriate safety and health practices and deter-
mine the applicability of regulatory limitations prior to use. water resistance; they may have a different composition than
the reinforced wall and the thicknesses of these internal and
2. Referenced Documents
external surfaces may be measured when their boundary limits
2
2.1 ASTM Standards: are visually indentifiable and if they are each at least 0.005 in.
D4166 Test Method for Measurement of Thickness of (0.10 mm) in thickness.
Nonmagnetic Materials by Means of a Digital Magnetic 3.1.5 reinforced thermosetting resin pipe (RTRP)—a fiber-
3
Intensity Instrument glass pipe without aggregate.
2.2 ANSI Standard: 3.1.6 reinforced wall thickness—the total wall thickness
minus the liner or exterior surface layer thickness, or both.
1
4. Significance and Use
ThispracticeisunderthejurisdictionofASTMCommitteeD20onPlasticsand
is the direct responsibility of Subcommittee D20.23 on Reinforced Plastic Piping
4.1 This practice provides for determining the physical
Systems and Chemical Equipment.
dimensions of fiberglass pipe and fittings. This practice is
Current edition approved Oct. 15, 2006. Published Oct. 2006. Originally
approved in 1977. Last previous edition approved in 1997 as D3567–97. DOI: suitable for determination of dimensional compliance with
10.1520/D3567-97R06.
product specifications.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
4
Standards volume information, refer to the standard’s Document Summary page on Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036, http://www.ansi.org.
3 5
Withdrawn. The last approved version of this historical standard is referenced Available from American Petroleum Institute (API), 1220 L. St., NW, Wash-
on www.astm.org. ington, DC 20005-4070, http://api-ec.api.org.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D3567–97 (2006)
5. Conditioning 7.3.2 Reinforced Wall and Liner Thickness—Measure the
cut surface of the pipe or fitting by setting a major scale
5.1 Testconditionsformeasur
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D2517-18(2023)(Specification)
Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings

ABSTRACT
This specification focuses on the requirements and methods of testing for materials, dimensions and tolerances, hydrostatic-burst strength, chemical resistance, and longitudinal tensile properties, for reinforced epoxy resin pipes and fittings for use in gas mains and services for direct burial and insertion applications. Pipes and fittings covered here are intended for use in the distribution of natural gas, petroleum fuels (propane-air and propane-butane vapor mixtures), and manufactured and mixed gases, where resistance to gas permeation, toughness, resistance to corrosion, aging, and deterioration from water, gas, and gas additives are required.
SCOPE
1.1 This specification covers requirements and methods of test for materials, dimensions and tolerances, hydrostatic-burst strength, chemical resistance, and longitudinal tensile properties, for reinforced epoxy resin pipe and fittings for use in gas mains and services for direct burial and insertion applications. The pipe and fittings covered by this specification are intended for use in the distribution of natural gas, petroleum fuels (propane–air and propane–butane vapor mixtures), manufactured and mixed gases where resistance to gas permeation, toughness, resistance to corrosion, aging, and deterioration from water, gas, and gas additives are required. Methods of marking are also given. Design considerations are discussed in Appendix X1.  
1.2 The values in SI units are to be regarded as the standard.  
1.3 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: There is no known ISO equivalent to this standard.  
1.4 A recommended inplant quality control program is given in Appendix X2.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM D5677-17(2023)(Specification)
Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings, Adhesive Bonded Joint Type, for Aviation Jet Turbine Fuel Lines

ABSTRACT
This specification covers reinforced plastic pipe and fitting system made from epoxy resin and glass-fiber reinforcement, together with adhesive for joint assembly, intended for services in aviation jet turbine fuel lines installed below ground. The fiberglass pipe shall be round and straight, and the pipe and fittings shall be of uniform density, resin content, and surface finish. Tests shall be conducted on the specimen to determine compliance with the following performance requirements: joint strength; hydrostatic strength; impact resistance; boil resistance; external load resistance; and degradation resistance.
SCOPE
1.1 This specification covers a reinforced plastic pipe and fittings system made from epoxy resin and glass-fiber reinforcement, together with adhesive for joint assembly, intended for service up to 150°F (65.6°C) and 150-psig (1034-kPa) operating pressure and surges up to 275 psig (1896 kPa) in aviation jet turbine fuel lines installed below ground.  
1.2 The dimensionless designator NPS has been substituted in this specification for such traditional terms as nominal diameter, size, and nominal size.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values in parentheses are for information only.  
1.4 The following safety hazards caveat pertains only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: There is no known ISO equivalent to this standard.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM D6041-23(Specification)
Standard Specification for Contact-Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings

SCOPE
1.1 This specification covers pipe and fittings fabricated by contact molding, for pressures to 150 psi and made of a commercial-grade polyester resin. Included are requirements for materials, properties, design, construction, dimensions, tolerances, workmanship, and appearance.  
1.2 This specification does not cover resins other than polyester, reinforcing materials other than glass fibers or fabrication methods other than contact molding.
Note 1: For the purposes of this specification, the term polyester resin will include both polyester and vinylester resins.  
1.3 This specification does not cover the design of pipe and fittings intended for use with liquids heated above their flash points.  
1.4 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are provided for information purposes only.  
1.5 The following precautionary caveat pertains only to Section 10, the test methods portion, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 2: There is no known ISO equivalent to this standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D2992-22(Practice)
Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings

SIGNIFICANCE AND USE
5.1 This practice is useful for establishing the hoop stress or internal pressure versus time-to-failure relationships, under selected internal and external environments which simulate actual anticipated product end-use conditions, from which a design basis for specific piping products and materials can be obtained. This practice defines an HDB for material in straight, hollow cylindrical shapes where hoop stress can be easily calculated, and a PDB for fittings and joints where stresses are more complex.  
5.1.1 An alternative design practice based on initial strain versus time-to-failure relationships employs a strain basis HDB instead of the stress basis HDB defined by this practice. The strain basis HDB is most often used for buried pipe designs with internal pressures ranging from 0 to 250 psig (1.72 MPa).  
5.2 To characterize fiberglass piping products, it is necessary to establish the stress versus cycles or time to failure, or pressure versus cycles or time to failure relationships over three or more logarithmic decades of time (cycles or hours) within controlled environmental parameters. Because of the nature of the test and specimens employed, no single line can adequately represent the data. Therefore, the confidence limits shall be established.  
5.3 Pressure ratings for piping of various dimensions at each temperature may be calculated using the HDS determined by testing one size of piping provided that the same specific process and material are used both for test specimens and the piping in question.  
5.4 Pressure ratings at each temperature for components other than straight hollow shapes may be calculated using the HDP determined by testing one size of piping provided that (1) the specific materials and manufacturing process used for the test specimens are used for the components, (2) for joints, the joining materials and procedures used to prepare the test specimens are used for field joining, and (3) scaling of critical dimensions is related ...
SCOPE
1.1 This practice establishes two procedures, Procedure A (cyclic) and Procedure B (static), for obtaining a hydrostatic design basis (HDB) or a pressure design basis (PDB) for fiberglass piping products, by evaluating strength-regression data derived from testing pipe or fittings, or both, of the same materials and construction, either separately or in assemblies. Both glass-fiber-reinforced thermosetting-resin pipe (RTRP) and glass-fiber-reinforced polymer mortar pipe (RPMP) are fiberglass pipe.
Note 1: For the purposes of this standard, polymer does not include natural polymers.  
1.2 This practice can be used for the HDB determination for fiberglass pipe where the ratio of outside diameter to wall thickness is 10:1 or more.  
Note 2: This limitation, based on thin-wall pipe design theory, serves further to limit the application of this practice to internal pressures which, by the hoop-stress equation, are approximately 20 % of the derived hydrostatic design stress (HDS). For example, if HDS is 5000 psi (34 500 kPa), the pipe is limited to about 1000-psig (6900-kPa) internal pressure, regardless of diameter.
Note 3: Where long (continuous) glass fibers are intentionally placed to resist the planned pressure load case (that is, free end pressure testing and 654.7° fiberglass windings) the results from this practice may be overly conservative in predicting long term fiberglass pipe performance when the same pipe is operated at lower (non-damaging) stresses typical in normal pipeline applications.
Note 4: All data points in the analysis shall be of the same failure mode. Where plastic creep of the resin leading to pipe failure is precluded by unintended resin matrix cracking or other unanticipated modes of failure, this practice may not accurately represent the pipe’s life expectancy.  
1.3 This practice provides a PDB for complex-shaped products or systems where complex stress fields seriously inhibit the use of h...

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D3567-17(2022)(Practice)
Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings

SIGNIFICANCE AND USE
4.1 This practice provides for determining the physical dimensions of fiberglass pipe and fittings. This practice is suitable for determination of dimensional compliance with product specifications.
SCOPE
1.1 This practice covers the determination of outside diameter, inside diameter, total wall thickness, reinforced wall thickness, liner thickness (where applicable), and length dimensions of “fiberglass” (glass-fiber-reinforced thermosetting resin) pipe. Included are procedures for measuring tapered dimensions and taper angles for pipe intended to be joined by tapered socket fittings, and procedures for gaging internal and external threads.  
1.2 This practice also includes procedures for determining dimensions for fiberglass pipe fittings.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
Note 1: There is no known ISO equivalent to this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3965-21(Specification)
Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings

ABSTRACT
This specification covers materials made from only virgin ABS polymers and blends of ABS polymers suitable for use in the extrusion of pipe and molding of fittings. ABS polymers and blends of ABS polymers shall be classified according to cell limits: Cell 0; Cell 1; Cell 2; Cell 3; Cell 4; and Cell 5. The ABS material shall be produced by polymerization of the monomers, acrylonitrile, butadiene, and styrene, or their closely related chemical derivatives, or from a blend of ABS polymers from those monomers. The blend of ABS polymers can be intimately mixed by melt compounding, or it can be a homogeneous physical mixture of discrete ABS polymers. Materials shall be measured using techniques in accordance with the following test methods: impact testing; deflection temperature under load; tensile stress at yield point; modulus of elasticity in tension; and specific gravity.
SCOPE
1.1 This classification system covers materials made from only virgin ABS polymers and blends of ABS polymers suitable for use in the extrusion of pipe and molding of fittings.  
1.2 The requirements of this classification system are applicable only to the ABS polymers and blends of ABS polymers as classified and do not address the requirements of the finished pipe or fittings. The applicable ASTM standard specification for pipe or fittings shall be consulted for their requirements.  
1.3 This classification system excludes ABS polymers and blends of ABS polymers made from reprocessed, regrind, reclaimed, or recycled materials. ABS rework, generated in-house by the original plastic manufacturer, is allowed to be used by that original manufacturer, provided the ABS product shipped meets the physical and mechanical properties required by its callout in Table 1.  
1.4 This classification system and subsequent line callout (specification) provides a means for describing ABS materials used in the manufacture of pipe and fittings. It is not intended for the selection of materials. Material selection shall be made by those having expertise in the plastics field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the inherent properties of the material other than those covered by this classification system, and the economics.  
1.5 This classification system and subsequent line callout (specification) provides for the classification of ABS polymers and blends of ABS polymers into groups based on five properties: Izod impact strength at room temperature, Izod impact strength at low temperature, deflection temperature under load, tensile stress at yield point, and modulus of elasticity in tension. The properties included are those required to identify the ABS material by the cell classifications.  
Note 1: Other requirements necessary to identify particular characteristics of ABS polymers and blends of ABS polymers will be added as test methods become available or the need is identified.
Note 2: Due to pipe and fitting standards requirements a separate standard is planned for recycled materials.  
1.6 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.7 The following safety hazards caveat pertains only to the test methods portion, Section 13, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 3: This standard and ISO 7245-1984 address the same subject matter, but differ in technical content.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the De...

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3350-21(Specification)
Standard Specification for Polyethylene Plastics Pipe and Fittings Materials

ABSTRACT
This specification covers the identification of polyethylene plastic pipe and fitting materials. Cell classification of materials shall be according to tests of primary properties like density, melt index, flexural modulus, tensile strength at yield, slow crack growth resistance, and hydrostatic strength classification. Materials shall be manufactured by molding and extrusion of polyethylene plastic in the form of powder, granules, or pellets. Color and ultraviolet stabilizer, thermal stability, brittleness temperature, density, tensile strength at yield, and elongation at break shall conform to this specification.
SCOPE
1.1 This specification covers the identification of polyethylene plastic pipe and fittings materials in accordance with a cell classification system. It is not the function of this specification to provide specific engineering data for design purposes, to specify manufacturing tolerances, or to determine suitability for use for a specific application.  
1.1.1 Some plastic pipe and fitting PE compounds classified by this standard are sold as a base material and then combined with other material(s) (for example, color or additive concentrate) by the pipe or fitting manufacturer into a final classified compound either prior to or during production of the final article. This standard, excluding the requirements of Table 1, properties 5 and 6, and 6.1.1, can be used for property verification of the incoming base material(s) in accordance with 8.1.  
1.1.2 In the case of PE compounds sold as the compound classified by the standard, see 8.1 regarding property verification of the incoming classified compound.  
1.1.3 Compounds with a cell classification value other than ‘0’ for the Hydrostatic Strength Classification (property 6) rely on a defined formulation. The composition of the defined formulation can be obtained from the owner of the formulation.
Note 1: Deviations from the defined formulation may affect the Hydrostatic Strength Classification.  
1.2 Polyethylene plastic materials, being thermoplastic, are reprocessable and recyclable (Note 3). This specification allows for the use of those polyethylene materials, provided that all specific requirements of this specification are met.
Note 2: The notes in this specification are for information only and shall not be considered part of this specification.
Note 3: See Guide D5033 for information and definitions related to recycled plastics.  
1.3 The values stated in SI units are to be regarded as standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 4: There is no known ISO equivalent to this standard.  
1.5 For information regarding molding and extrusion materials see Specification D4976. For information regarding wire and cable materials see Specification D1248.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM D2152-23(Test Method)
Standard Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone Immersion

SIGNIFICANCE AND USE
3.1 This test method is applicable only for distinguishing between inadequately fused and adequately fused PVC. The difference between thermally degraded and adequately fused PVC cannot be detected by this test method. Acetone immersion testing is not a substitute for burst, impact, or other physical or chemical tests on PVC pipe or fittings and it, therefore, shall not be used as the only test specification for purchasing of PVC pipe and fittings. This test method only detects inadequate fusion and does not determine the over-all quality of the PVC pipe or fittings.  
3.2 This test method is useful in determining whether inadequate fusion contributed to failure of PVC pipe or fittings in other physical or chemical tests, or in service.  
3.3 This test method is useful in evaluating the adequacy of PVC fusion obtained in process or materials trials.  
3.4 This test method determines adequacy of fusion on a single, relatively small specimen. This test method requires the use of a hazardous reagent which must be properly handled and disposed. Therefore, this test method may not be cost-effective to employ as a routine quality control test.
SCOPE
1.1 This test method covers the determination of the adequacy of fusion of extruded rigid poly(vinyl chloride) (PVC) pipe and molded fittings as indicated by reaction to immersion in anhydrous acetone.  
1.2 The values stated in inch-pound units are to be regarded as the standard except where instruments are calibrated in SI units.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.Specific hazards statements are given in Annex A1.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F2945-18(2023)(Specification)
Standard Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings

ABSTRACT
This specification covers requirements and test methods for the characterization of polyamide 11 pipe, tubing, and fittings for use in fuel gas piping. The pipe and fittings covered by this specification are intended for use in the transport of fuel gases. This specification does not cover threaded pipe. The polyamide 11 material used to make pipe and fittings shall be virgin or reworked material and shall have a Plastics Pipe Institute (PPI) long-term hydrostatic design stress and hydrostatic design basis rating as determined per PPI TR3 and PPI TR4. This specification deals with requirements for materials, requirements for pipe and fittings, test methods, marking, and quality Assurance.
SCOPE
1.1 This specification covers requirements and test methods for the characterization of polyamide 11 pipe, tubing, and fittings for use in fuel gas pipelines. The pipe and fittings covered by this specification are intended for use in the distribution and transmission of fuel gases.  
1.1.1 This specification does not cover threaded pipe. Generic fusion guidelines are given in Appendix X1. Design considerations are discussed in Appendix X2. In-plant quality control programs are specified in Annex A1.  
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
Note 1: Heat fusion joining of PA11 pipe and fittings meeting the requirements of this standard is limited to PA11 pipe and fittings meeting the requirements of this standard. Heat Fusion joining of PA11 pipe and fittings meeting the requirements of this standard is not allowed to pipes and fittings made from any other thermoplastic materials (for example, PA12, PEs, PVCs, etc.).  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following is an index of the annexes and appendixes in this specification:    
Annexes  
Subject  
Annex A1  
In-Plant Quality Control for sizes up to 12 in.  
Annex A2  
PA-11 Butt Fusion Fittings  
Appendixes  
Subject  
Appendix X1  
Butt Fusion Guidelines for PA-11 Piping  
Appendix X2  
Design Consideration  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    15 pages
    English language
    sale 15% off
ASTM
ASTM D2517-18(2023)(Specification)
Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings

ABSTRACT
This specification focuses on the requirements and methods of testing for materials, dimensions and tolerances, hydrostatic-burst strength, chemical resistance, and longitudinal tensile properties, for reinforced epoxy resin pipes and fittings for use in gas mains and services for direct burial and insertion applications. Pipes and fittings covered here are intended for use in the distribution of natural gas, petroleum fuels (propane-air and propane-butane vapor mixtures), and manufactured and mixed gases, where resistance to gas permeation, toughness, resistance to corrosion, aging, and deterioration from water, gas, and gas additives are required.
SCOPE
1.1 This specification covers requirements and methods of test for materials, dimensions and tolerances, hydrostatic-burst strength, chemical resistance, and longitudinal tensile properties, for reinforced epoxy resin pipe and fittings for use in gas mains and services for direct burial and insertion applications. The pipe and fittings covered by this specification are intended for use in the distribution of natural gas, petroleum fuels (propane–air and propane–butane vapor mixtures), manufactured and mixed gases where resistance to gas permeation, toughness, resistance to corrosion, aging, and deterioration from water, gas, and gas additives are required. Methods of marking are also given. Design considerations are discussed in Appendix X1.  
1.2 The values in SI units are to be regarded as the standard.  
1.3 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: There is no known ISO equivalent to this standard.  
1.4 A recommended inplant quality control program is given in Appendix X2.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off