ASTM A845-85(2000)

Standard Specification for Titanium Scrap for Use in Deoxidation and Alloying of Steel (Withdrawn 2005)

SCOPE
1.1 This specification covers titanium and titanium alloys in the form of processed scrap, designated as shown in Table 1, for use in the manufacture of steel.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units may be approximate.
WITHDRAWN RATIONALE
This specification covered titanium and titanium alloys in the form of processed scrap for use in the manufacture of steel. This specification was withdrawn because there is no known use for it.
Formerly under the jurisdiction of Committee A01 on Steel, Stainless Steel, and Related Alloys, this specification was withdrawn in September 2005.

General Information

• Status: Withdrawn
• Publication Date: 09-Mar-2000
• Withdrawal Date: 09-Oct-2005
• ICS: 77.150.50 - Titanium products
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.18 - Castings

Relations

• Referred By: ASTM A1025/A1025M-10(2020) - Standard Specification for Ferroalloys and Other Alloying Materials, General Requirements
• Effective Date: 10-Mar-2000

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A 845 – 85 (Reapproved 2000)
Standard Specification for
Titanium Scrap for Use in Deoxidation and Alloying of Steel
This standard is issued under the fixed designation A 845; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
TABLE 1 Chemical Requirements
1. Scope
1.1 This specification covers titanium and titanium alloys in NOTE— Material of Grade 1 shall be chemically washed and dried or
ultrasonically cleaned or processed, or both by a method agreed between
the form of processed scrap, designated as shown in Table 1,
buyer and seller.
for use in the manufacture of steel.
Grade Ti, %, Al, %, V, %, Ni + Cr Sn, %, Pb + C, %,
1.2 The values stated in inch-pound units are to be regarded
min max max +Mo+ max Bi, %, max
as the standard. The metric equivalents of inch-pound units
Fe, %, max
may be approximate.
max
1(Note1) 87.0 6.5 4.5 2.0 1.00 0.01 0.15
2. Referenced Documents
2 85.0 . . . 3.00 0.02 0.50
2.1 ASTM Standards:
E 120 Test Methods for ChemicalAnalysis of Titanium and
7. Methods of Chemical Analysis
Titanium Alloys
7.1 The chemical analysis for contaminants shall be made in
3. Ordering Information
accordance with Methods E 120 or by any other approved
method agreed upon by the manufacturer and the purchaser.
3.1 Orders for material under this specification shall include
The analysis may be made by instrumental methods, provided
the following information:
that, in case of dispute, the results secured by Methods E 120,
3.1.1 Quantity,
shall be the basis for acceptance.
3.1.2 Name or form of material,
3.1.3 Size desired,
8. Inspection
3.1.4 Requirement for packaging, and
8.1 If the purchaser desires to make an inspection of the
3.1.5 Reports requested with shipment.
material at the manufacturer’s works where the material is
4. Materials and Manufacture
processed, it shall be so stated in the contract or purchaser
order.
4.1 The material may be in the form of titanium processing
8.2 If the purchaser elects to make an inspection made at the
scrap;orcutuprolledsectionswithindividualweighttolerance
manufacturer’s plant, the manufacturer shall afford the inspec-
as agreed between buyer and seller.
tor representing the purchaser all reasonable facilities to satisfy
4.2 The material may be delivered loose or pressed into
him that the material is being furnished in accordance with this
pieces, as agreed between buyer and seller.
specification. All tests and inspection shall be so conducted as
5. Chemical Composition
not to interfere unnecessarily with the operation of the works.
5.1 The material shall conform to the requirements as to
9. Rejection
chemical composition prescribed in Table 1.
9.1 Material that does not conform to the requirements of
6. Sampling
this specification may be rejected, and if rejected, sh
...