ASTM D1752-04a(2008)
(Specification)Standard Specification for Preformed Sponge Rubber Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction
Standard Specification for Preformed Sponge Rubber Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction
ABSTRACT
This specification covers preformed expansion joint fillers for use in concrete, brick, stone, and other paving and structural construction. The fillers are available in the following types: Type I, sponge rubber, which shall consist of preformed strips of a durable elastic sponge rubber compound using synthetic rubber or natural rubber as a base and containing no reclaim rubber or factice; Type II, cork, and Type III, self-expanding cork, which shall both consist of preformed strips that have been formed from clean granulated cork particles securely bound together by a synthetic resin of an incoluble nature; and Type IV, recycled PVC, which shall consist of preformed strips that have been extruded using scrap PVC material and using either no binder or a synthetic resin of an insoluble nature to securely bind it together. Materials shall be sampled suitably according to specified size and number, and shall meet property requirements as to recovery, compression, extrusion, expansion, boiling in hydrochloric acid, and density.
SCOPE
1.1 This specification covers preformed expansion joint fillers of the following four types for use in concrete, brick, or stone construction.
1.1.1 Type I—Sponge rubber.
1.1.2 Type II—Cork.
1.1.3 Type III—Self-expanding cork.
1.1.4 Type IV—Recycled PVC.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Note 1—Attention is called to Specification D 994 and D 1751.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D1752 −04a(Reapproved 2008)
Standard Specification for
Preformed Sponge Rubber Cork and Recycled PVC
Expansion Joint Fillers for Concrete Paving and Structural
1
Construction
This standard is issued under the fixed designation D1752; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope lengths of 3, 5, 6, 10, or 12 ft. Purchaser must specify sheet
sizes when ordering (excluding Type IV–Recycled PVC).
1.1 This specification covers preformed expansion joint
fillers of the following four types for use in concrete, brick, or 3.2 Joint filler in strip form is cut from the sheets as
stone construction. manufactured. When ordering joint filler strips the purchaser
1.1.1 Type I—Sponge rubber. must specify thickness, widths, and length; strip widths are
1
1.1.2 Type II—Cork. available from 2 in. (50 mm) in increments of ⁄2 in. (13 mm).
1.1.3 Type III—Self-expanding cork.
3.3 Type IV joint filler is available in strip form, cut from
1.1.4 Type IV—Recycled PVC.
the sheets as manufactured, and available in a range of
1 3 1 3
thicknesses: ⁄4 in., ⁄8 in., ⁄2 in., or ⁄4 in. When ordering joint
1.2 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical filler strips, the purchaser must specify thickness, widths, and
length; strip widths are available from 2 in. (50 mm) in
conversions to SI units that are provided for information only
1
increments of ⁄2 in. (13 mm).
and are not considered standard.
NOTE 1—Attention is called to Specification D994 and D1751. 4. Materials
4.1 Sponge Rubber—The joint filler shall consist of pre-
2. Referenced Documents
formed strips of a durable, elastic sponge rubber compound,
2
2.1 ASTM Standards:
using synthetic rubber or natural rubber as a base and contain-
D545 Test Methods for Preformed Expansion Joint Fillers
ing no reclaim rubber or factice. Unless otherwise specified,
for Concrete Construction (Nonextruding and Resilient
the sponge rubber shall have a cement gray color to blend with
Types)
concrete in appearance.
D994 Specification for Preformed Expansion Joint Filler for
4.2 Cork and Self-Expanding Cork—The joint filler shall
Concrete (Bituminous Type)
consist of preformed strips that have been formed from clean
D1751 Specification for Preformed Expansion Joint Filler
granulated cork particles securely bound together by a syn-
for Concrete Paving and Structural Construction (Nonex-
thetic resin of an insoluble nature.
truding and Resilient Bituminous Types)
4.3 Recycled PVC—The joint filler shall consist of pre-
3. Ordering Information formed strips that have been extruded using scrap PVC
material and using either no binder or a synthetic resin of an
3.1 Products conforming to this specification are manufac-
insoluble nature to securely bind it together. Unless otherwise
1 3 1
tured in sheet form to a range of thicknesses: ⁄4 in., ⁄8 in., ⁄2
specified, the recycled PVC should have a cement gray color to
3
in., ⁄4 in., and 1 in. Sheet sizes may be 3 or 4 ft in width and
blend with concrete in appearance.
4.4 Preformed strips of expansion joint fillers shall be of
1
This specification is under the jurisdiction of ASTM Committee D04 on Road
such character as not to be deformed or broken by ordinary
and Paving Materials and is the direct responsibility of Subcommittee D04.34 on
handling when exposed to atmospheric conditions. Pieces of
Preformed Joint Fillers, Sealers and Sealing Systems.
the joint filler which have been damaged shall be rejected.
Current edition approved Dec. 1, 2008. Published January 2009. Originally
approved in 1960. Last previous edition approved in 2004 as D1752 – 04a. DOI:
5. Requirements
10.1520/D1752-04AR08.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
5.1 Test Specimen—The sample to be tested shall be cut
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
from the sheet, as manufactured, and shall be representative of
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. the sheet stock.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D1752−04a (2008)
5.2 Recovery—The test specimen shall be compressed to 6. Dimensions and Permissible Variations
50 % of its thickness before test. The load shall be released
6.1 The preformed strips shall conform to the dimensions
immediately after application.
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D1752–04 Designation: D 1752 – 04a (Reapproved 2008)
Standard Specification for
Preformed Sponge Rubber Cork and Recycled PVC
Expansion Joint Fillers for Concrete Paving and Structural
1
Construction
This standard is issued under the fixed designation D 1752; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers preformed expansion joint fillers of the following four types for use in concrete, brick, or stone
construction.
1.1.1 Type I—Sponge rubber.
1.1.2 Type II—Cork.
1.1.3 Type III—Self-expanding cork.
1.1.4 Type IV—Recycled PVC.
1.2The values stated in inch-pound units are to be regarded as the standard.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
NOTE 1—Attention is called to Specification D 994 and D 1751.
2. Referenced Documents
2
2.1 ASTM Standards:
D 545 Test Methods for Preformed Expansion Joint Fillers for Concrete Construction (Nonextruding and Resilient Types)
D 994 Specification for Preformed Expansion Joint Filler for Concrete (Bituminous Type)
D 1751 Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and
Resilient Bituminous Types)
3. Ordering Information
1 3 1 3
3.1 Products conforming to this specification are manufactured in sheet form to a range of thicknesses: ⁄4 in., ⁄8 in., ⁄2 in., ⁄4
in., and 1 in. Sheet sizes may be 3 or 4 ft in width and lengths of 3, 5, 6, 10, or 12 ft. Purchaser must specify sheet sizes when
ordering (excluding Type IV–Recycled PVC).
3.2 Joint filler in strip form is cut from the sheets as manufactured. When ordering joint filler strips the purchaser must specify
1
thickness, widths, and length; strip widths are available from 2 in. (50 mm) in increments of ⁄2 in. (13 mm).
3.3 Type IV joint filler is available in strip form, cut from the sheets as manufactured, and available in a range of thicknesses:
1 3 1 3
⁄4 in., ⁄8 in., ⁄2 in., or ⁄4 in.When ordering joint filler strips, the purchaser must specify thickness, widths, and length; strip widths
1
are available from 2 in. (50 mm) in increments of ⁄2 in. (13 mm).
4. Materials
4.1 Sponge Rubber— The joint filler shall consist of preformed strips of a durable, elastic sponge rubber compound, using
synthetic rubber or natural rubber as a base and containing no reclaim rubber or factice. Unless otherwise specified, the sponge
rubber shall have a cement gray color to blend with concrete in appearance.
4.2 Cork and Self-Expanding Cork —The joint filler shall consist of preformed strips that have been formed from clean
granulated cork particles securely bound together by a synthetic resin of an insoluble nature.
1
ThisspecificationisunderthejurisdictionofASTMCommitteeD04onRoadandPavingMaterialsandisthedirectresponsibilityofSubcommitteeD04.34onPreformed
Joint Fillers, Sealers,Sealers and Sealing Systems.
Current edition approved Jan.Dec. 1, 2004.2008. Published February 2004.January 2009. Originally approved in 1960. Last previous edition approved in 19962004 as
´1
D1752–84(1996) .D 1752 – 04a.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book ofASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D 1752 – 04a (2008)
4.3 Recycled PVC— The joint filler shall consist of preformed strips that have been extruded using scrap PVC material and
using either no binder or a synthetic resin of an insoluble nature to securely bind it together. Note2—UnlessUnless otherwise
specified, the recycled PVC should have a cement gray color to blend with concrete in appearance.
4.4 Preformed strips of expansion joint fillers shall be of such character as not to be deformed or broken by ordinary handling
when exposed to atmospheric conditions. Pieces of the joint filler which have been damaged shall be rejected.
5.
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D1752–04a Designation: D 1752 – 04a (Reapproved 2008)
Standard Specification for
Preformed Sponge Rubber Cork and Recycled PVC
Expansion Joint Fillers for Concrete Paving and Structural
1
Construction
This standard is issued under the fixed designation D 1752; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers preformed expansion joint fillers of the following four types for use in concrete, brick, or stone
construction.
1.1.1 Type I—Sponge rubber.
1.1.2 Type II—Cork.
1.1.3 Type III—Self-expanding cork.
1.1.4 Type IV—Recycled PVC.
1.2The values stated in inch-pound units are to be regarded as the standard.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
NOTE 1—Attention is called to Specification D 994 and D 1751.
2. Referenced Documents
2
2.1 ASTM Standards:
D 545 Test Methods for Preformed Expansion Joint Fillers for Concrete Construction (Nonextruding and Resilient Types)
D 994 Specification for Preformed Expansion Joint Filler for Concrete (Bituminous Type)
D 1751 Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and
Resilient Bituminous Types)
3. Ordering Information
1 3 1 3
3.1 Products conforming to this specification are manufactured in sheet form to a range of thicknesses: ⁄4 in., ⁄8 in., ⁄2 in., ⁄4
in., and 1 in. Sheet sizes may be 3 or 4 ft in width and lengths of 3, 5, 6, 10, or 12 ft. Purchaser must specify sheet sizes when
ordering (excluding Type IV–Recycled PVC).
3.2 Joint filler in strip form is cut from the sheets as manufactured. When ordering joint filler strips the purchaser must specify
1
thickness, widths, and length; strip widths are available from 2 in. (50 mm) in increments of ⁄2 in. (13 mm).
3.3 Type IV joint filler is available in strip form, cut from the sheets as manufactured, and available in a range of thicknesses:
1 3 1 3
⁄4 in., ⁄8 in., ⁄2 in., or ⁄4 in.When ordering joint filler strips, the purchaser must specify thickness, widths, and length; strip widths
1
are available from 2 in. (50 mm) in increments of ⁄2 in. (13 mm).
4. Materials
4.1 Sponge Rubber— The joint filler shall consist of preformed strips of a durable, elastic sponge rubber compound, using
synthetic rubber or natural rubber as a base and containing no reclaim rubber or factice. Unless otherwise specified, the sponge
rubber shall have a cement gray color to blend with concrete in appearance.
4.2 Cork and Self-Expanding Cork —The joint filler shall consist of preformed strips that have been formed from clean
granulated cork particles securely bound together by a synthetic resin of an insoluble nature.
4.3 Recycled PVC— The joint filler shall consist of preformed strips that have been extruded using scrap PVC material and
1
ThisspecificationisunderthejurisdictionofASTMCommitteeD04onRoadandPavingMaterialsandisthedirectresponsibilityofSubcommitteeD04.34onPreformed
Joint Fillers, Sealers,Sealers and Sealing Systems.
CurrenteditionapprovedJuneDec.1,2004.2008.PublishedJune2004.January2009.Originallyapprovedin1960.Lastpreviouseditionapprovedin2004asD 1752 – 04a.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book ofASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D 1752 – 04a (2008)
using either no binder or a synthetic resin of an insoluble nature to securely bind it together. Unless otherwise specified, the
recycled PVC should have a cement gray color to blend with concrete in appearance.
4.4 Preformed strips of expansion joint fillers shall be of such character as not to be deformed or broken by ordinary handling
when exposed to atmospheric conditions. Pieces of the joint filler which have been damaged shall be rejected.
5. Requirements Requirements
5.1 Test Specimen— The sample to
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.