iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM B902-04

(Specification)

Standard Specification for Compressed Round Stranded Copper Conductors, Hard, Medium-Hard, or Soft Using Single Input Wire Construction

Standard Specification for Compressed Round Stranded Copper Conductors, Hard, Medium-Hard, or Soft Using Single Input Wire Construction

SCOPE
1.1 This specification covers stranded conductors made from round copper wires, either uncoated or coated with tin, lead, or lead alloy for general use in insulated conductor assemblies for electrical purposes. These conductors shall be composed of one or more roller shaped or die closed layers of helically laid wires using the single input wire (SIW) methodology. (see Note 1 and Explanatory Note 1)Note 1
Sealed conductors which are intended to prevent longitudinal water propagation and are further covered/insulated, are also permitted within the guidelines of this specification.
1.2 The values stated in inch-pound or SI units are to be regarded separately as standard. The values in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
1.2.1 For density, resistivity, and temperature, the values stated in SI units are to be regarded as standard.

General Information

Status
Historical
Publication Date
31-Mar-2004
ICS
29.060.10 - Wires
Technical Committee
B01 - Electrical Conductors
Drafting Committee
B01.04 - Conductors of Copper and Copper Alloys
Current Stage
Ref Project

Relations

Replaces
ASTM B902-00 - Standard Specification for Compressed Round Stranded Copper Conductors, Hard, Medium-Hard, or Soft Using Single Input Wire Construction
Effective Date
01-Apr-2004
Replaced By
ASTM B902-04a - Standard Specification for Compressed Round Stranded Copper Conductors, Hard, Medium-Hard, or Soft Using Single Input Wire Construction
Effective Date
01-Sep-2004
Referred By
ASTM B226-11(2021) - Standard Specification for Cored, Annular, Concentric-Lay-Stranded Copper Conductors
Effective Date
01-Apr-2004

Buy Standard

ASTM B902-04 - Standard Specification for Compressed Round Stranded Copper Conductors, Hard, Medium-Hard, or Soft Using Single Input Wire ConstructionASTM B902-04 - Standard Specification for Compressed Round Stranded Copper Conductors, Hard, Medium-Hard, or Soft Using Single Input Wire Construction
PreviousNext
Technical specification
ASTM B902-04 - Standard Specification for Compressed Round Stranded Copper Conductors, Hard, Medium-Hard, or Soft Using Single Input Wire Construction
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B 902 – 04
Standard Specification for
Compressed Round Stranded Copper Conductors, Hard,
1
Medium-Hard, or Soft Using Single Input Wire Construction
This standard is issued under the fixed designation B 902; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope Area of Stranded Conductors
B 354 Terminology Relating to Uninsulated Metallic Elec-
1.1 This specification covers stranded conductors made
trical Conductors
from round copper wires, either uncoated or coated with tin,
4
2.2 Other Standard:
lead, or lead alloy for general use in insulated conductor
NBS Handbook 100: Copper Wire Tables
assemblies for electrical purposes. These conductors shall be
composed of one or more roller shaped or die closed layers of
3. Classification
helically laid wires using the single input wire (SIW) method-
3.1 The conductors described in this specification are in-
ology. (see Note 1 and Explanatory Note 1)
tended for subsequent insulation or covering. The classification
NOTE 1—Sealed conductors which are intended to prevent longitudinal
of these conductors is SIW compressed.
water propagation and are further covered/insulated, are also permitted
within the guidelines of this specification.
4. Ordering Information
1.2 The values stated in inch-pound or SI units are to be
4.1 Orders for material under this specification shall include
regarded separately as standard. The values in each system are
the following information:
not exact equivalents; therefore, each system shall be used
4.1.1 Quantity of each size,
independently of the other. Combining values from the two
4.1.2 Conductor size: circular-mil area or AWG (see Section
systems may result in nonconformance with the specification.
7),
1.2.1 For density, resistivity, and temperature, the values
4.1.3 Class: SIW compressed (see 1.2 and Table 1),
stated in SI units are to be regarded as standard.
4.1.4 Temper (see 5.3),
4.1.5 Whether coated or uncoated; if coated (see 5.1 and
2. Referenced Documents
5.2).
2
2.1 ASTM Standards:
4.1.6 Details of special-purpose lays, if required (see 7.3).
B 1 Specification of Hard-Drawn Copper Wire
4.1.7 When physical tests shall be made (see 10.2 and 10.3).
B 2 Specification for Medium-Hard-Drawn Copper Wire
4.1.8 Package size (see 16.1).
B 3 Specification for Soft or Annealed Copper Wire
4.1.9 Lagging, if required (see 16.2).
B 33 Specification for Tinned Soft or Annealed Copper
4.1.10 Special package marking, if required (see Section
Wire for Electrical Purposes
16.3), and
B 189 Specification for Lead-Coated and Lead-Alloy-
4.1.11 Place of inspection (see Section 15).
3
Coated Soft Copper Wire for Electrical Purposes
5. Requirements for Wires
B 193 Test Method for Resistivity of Electrical Conductor
Materials
5.1 The purchaser shall designate the type of wire and the
B 246 Specification for Tinned Hard-Drawn and Medium-
kind of coating, if any, to be used in the conductor.
Hard-Drawn Copper Wire for Electrical Purposes
5.2 Before stranding, the copper wire used shall meet all of
B 263 Test Method for Determination of Cross-Sectional
the requirements of the following specifications of ASTM that
are applicable to its type:
5.2.1 Specification B 3,
1
This specification is under the jurisdiction of ASTM Committee B01 of
5.2.2 Specification B 33,
Electrical Conductors and is the direct responsibility of Subcommittee B01.04 on
5.2.3 Specification B 2,
Conductors of Copper Alloys.
Current edition approved April 1, 2004. Published April 2004. Orignally 5.2.4 Specification B 1,
approved in 2000. Last previous edition approved in 2000 as B 902 – 00.
5.2.5 Specification B 189, and
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
4
the ASTM website. Available from National Technical Information Service, 5285 Port Royal Road,
3
Withdrawn. Springfield, VA 22161.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
B902–04
TABLE 1 Construction Requirements of Compressed Round SIW Standard Copper Conductors
Compressed Strand Dimensions
Conductor Size Nominal Nominal
Diameter Diameter
of SIW of SIW
Minimum Compressed Compressed
Number of Conductor, Conductor, Mass DC Resistance at 20°C
2
cmils AWG mm Wires in. mm. lb/1000ft kg/km V/1000ft V/km
5 000 000 2534 217 2.424 61.57 15890 23649 0.00218 0.00715
4 500 000 2280 217 2.300 58.41 14300 21283 0.00242 0
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM B606/B606M-23(Specification)
Standard Specification for High-Strength Zinc-Coated (Galvanized) Steel Core Wire for Use in Overhead Electrical Conductors

ABSTRACT
This specification covers the standard requirements for round, high-strength, zinc-coated (galvanized), steel core wire with Class A zinc coating used for mechanical reinforcement in the manufacture of special steel reinforced aluminum and aluminum-alloy conductors. The base metal shall be steel produced by the open-hearth, electric-furnace, or basic-oxygen process and the wire shall be cold drawn and coated with zinc. Joints may be made at any stage of processing prior to final cold drawing by the electric butt-weld or flash-welding process. Chemical analysis shall be conducted; wherein, the steel shall conform to the chemical composition requirements for carbon, manganese, phosphorus, sulfur, and silicon. The zinc-coated steel core wire shall conform to the tensile strength and elongation requirements which shall be obtained using a tensile test method. The material shall also undergo wrap and adherence tests; wherein, the wire shall be capable of being wrapped in a close helix without cracking or flaking.
SCOPE
1.1 This specification covers round, high-strength, zinc-coated (galvanized), steel core wire with Class A zinc coating (GA3) for use in overhead electrical conductors.  
1.2 This specification covers wire of diameter from 0.0500 in. to 0.1900 in. inclusive or 1.27 mm to 4.82 mm inclusive.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM B1005-17(2023)(Specification)
Standard Specification for Copper-Clad Aluminum Bar for Electrical Purposes (Bus Bar)

ABSTRACT
This specification covers the manufacturing and testing requirements for copper clad aluminum rectangular bar for electrical (bus) applications. Six classes of copper-clad aluminum bar are covered:
SCOPE
1.1 This specification covers copper clad aluminum rectangular bar for electrical (bus) applications.  
1.2 Six classes of copper-clad aluminum bar are covered as follows:
Class 20A—Nominal 20 volume % copper, annealed.
Class 25A—Nominal 25 volume % copper, annealed.
Class 30A—Nominal 30 volume % copper, annealed.
Class 20H—Nominal 20 volume % copper, hard-worked.
Class 25H—Nominal 25 volume % copper, hard-worked.
Class 30H—Nominal 30 volume % copper, hard-worked.  
1.3 The values stated in inch-pound units are to be regarded as the standard, except for resistivity and density, where the SI units are the standard. The values given in parentheses are for information only.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM B520-12(2023)(Specification)
Standard Specification for Tin-Coated, Copper-Clad Steel Wire for Electronic Application

ABSTRACT
This specification covers tin-coated, copper-clad steel wires for electronic applications. The four classes of steel wires considered here are: hard-drawn wires with 30% nominal conductivity (Class T30HS); annealed wires with 30% nominal conductivity (Class T30A); hard-drawn wires with 40% nominal conductivity (Class T40HS); and annealed wires with 40% nominal conductivity (Class T40A). Specimens shall go through tests and shall adhere to specified requirements for dimensions, electrical resistivity, tensile strength, and coating continuity and adherence.
SCOPE
1.1 This specification covers tin-coated copper-clad steel wire for electronic application.  
1.2 Four classes of tin-coated copper-clad steel wire are covered as follows:  
1.2.1 Class T30HS—Nominal 30 % conductivity, hard-drawn,  
1.2.2 Class T30A—Nominal 30 % conductivity, annealed,  
1.2.3 Class T40HS—Nominal 40 % conductivity, hard-drawn, and  
1.2.4 Class T40A—Nominal 40 % conductivity, annealed.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3.1 Exception—The SI values for resistivity and volume are to be regarded as standard.  
1.4 The following safety hazards caveat pertains only to the test method portion, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Consideration should be given to toxicity and flammability when selecting solvent cleaners.)  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM B559-12(2023)(Specification)
Standard Specification for Nickel-Coated, Copper-Clad Steel Wire for Electronic Application

ABSTRACT
This specification covers nickel-coated, round, copper-clad steel wire for electronic applications. The nickel-coated wire shall consist of the basis wire coated with nickel. Tensile strength and elongation of the nickel-coated wire shall conform to the specified requirements for the applicable size and class of copper-clad steel wire. The electrical resistivity shall not exceed the values specified. Continuity, adherence, and mass of the coating shall be determined. Necessary joints in the wire and rod prior to final coating and drawing shall be made.
SCOPE
1.1 This specification covers nickel-coated, round, copper-clad steel wire for electronic application.  
1.2 Nickel coatings in mass percentages of the total mass of the coated wire are as follows: 2 %, 4 %, 7 %, 10 %, and 27 %. Nickel-coated wire having different minimum mass percentages of nickel may be obtained by mutual agreement between the manufacturer and the purchaser. For information purposes, the thickness of coating in microinches provided by the percentages listed above is shown in Table 1.  
1.3 Four classes of nickel-coated, copper-clad steel wire are covered as follows:  
1.3.1 Class N30HS—Nominal 30 % conductivity, hard drawn.  
1.3.2 Class N30A—Nominal 30 % conductivity, annealed.  
1.3.3 Class N40HS—Nominal 40 % conductivity, hard drawn.  
1.3.4 Class N40A—Nominal 40 % conductivity, annealed.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4.1 Exception—The SI values for resistivity are to be regarded as standard.  
1.5 The following safety hazards caveat pertains only to the test method described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.(Warning—Consideration should be given to toxicity and flammability when selecting solvent cleaners.)  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM B502/B502M-23(Specification)
Standard Specification for Aluminum-Clad Steel Core Wire for Use in Overhead Electrical Aluminum Conductors

ABSTRACT
This specification covers round, aluminum-clad steel core wire used for mechanical reinforcement in the manufacture of aluminum conductors, aluminum-clad steel reinforced. The base metal shall be steel produced by the openhearth, electric-furnace, or basic-oxygen process and shall be of such composition that the finished clad wire shall have the properties and characteristics prescribed in this specification. The aluminum used for cladding shall have a purity and quantity sufficient to meet thickness and resistance requirements of this specification. The material shall conform to the required tensile properties such as stress, tensile strength, and elongation. The aluminum-clad steel core shall undergo elongation test, tension test, and torsion test. The elongation test shall be determined by an extensometer equipped with a vernier or other instrument reading. In the torsion test, a small tensile load shall be applied to the specimen during testing. The specimen shall be twisted by rotating one of the vises in the same direction until fracture occurs.
SCOPE
1.1 This specification covers round, aluminum-clad steel core wire with two designations of tensile strengths, AW2 (Normal Strength) and AW3 (High Strength).  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.2.1 For conductor sizes designated by AWG, the requirements in SI units have been numerically converted from corresponding values stated or derived in inch-pound units. For conductor sizes designated by SI units only, the requirements are stated or derived in SI units.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM B869-07(2023)(Specification)
Standard Specification for Copper-Clad Steel Electrical Conductor for CATV Drop Wire

ABSTRACT
This specification covers hard-drawn round copper-clad steel electrical conductor for CATV drop wire (coaxial cable center conductor). The wire shall be composed of a steel core with a substantially uniform and continuous copper cladding thoroughly bonded to it throughout. The size shall be expressed as the diameter of the wire. The steel wire shall conform to the prescribed tensile strength, elongation, and breaking strength. Requirements for (1) tension and torsion tests, (2) method of determining the electrical resistance, (3) cladding uniformity in terms of thickness, and (4) joint construction are detailed. The prescribed density of the wire to be taken for calculating mass/unit length, cross section, and so forth is given.
SCOPE
1.1 This specification covers 21 % conductivity hard-drawn round copper-clad steel wire for coaxial cable center conductors (Note 1).  
Note 1: Wire ordered to this specification is not intended for redrawing since it is furnished in the hard-drawn temper. If wire is desired for the purpose, the manufacturer should be consulted.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM B978/B978M-23(Specification)
Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Aluminum Matrix Composite Reinforced (ACAMCR), Formerly ACCR

ABSTRACT
This specification applies to concentric-lay-stranded conductors made from round aluminum-zirconium alloy wires and an aluminum matrix composite (AMC) core wire(s) for use as overhead electrical conductors. It covers ordering information, requirements for wires, joints and lay, construction requirements, rated strength of conductor, density, mass per unit length and electrical resistance, and cross-sectional area. The standard also addresses workmanship, finish, and appearance, together with mechanical as well as electrical and dimensional tests, tests and retests, inspection, and packaging and package marking.
SCOPE
1.1 This specification covers concentric-lay-stranded conductors made from round aluminum-zirconium alloy wires and an aluminum matrix composite (AMC) core wire(s) for use as overhead electrical conductors (Explanatory Note 1 and Explanatory Note 2).  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM B857-22(Specification)
Standard Specification for Shaped Wire Compact Concentric-Lay-Stranded Aluminum Conductors, Coated-Steel Supported (ACSS/TW)

ABSTRACT
This specification covers shaped wire compact concentric-lay-stranded aluminum conductors, steel supported (ACSS/TW) for use as overhead electrical conductors. Electric-butt welds, cold-pressure welds, and electric-butt, cold upsed welds in the finished individual aluminum wires composing the conductor may be made during the stranding process. The electrical resistivity of the material shall meet the minimum resistivity specified. The rated strength of the completed conductor may be determined by mechanical tests. Mass and density of the conductors shall be determined.
SCOPE
1.1 This specification covers shaped wire compact concentric-lay-stranded aluminum conductors, steel supported (ACSS/TW) for use as overhead electrical conductors (see Explanatory Note 1).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.2.1 Exceptions—For conductor sizes designated by AWG or kcmil sizes, the requirements in SI units are numerically converted from the corresponding requirements in inch-pound units. For conductor sizes designated by SI units only, the requirements are stated or derived in SI units. For density, resistivity, and temperature, the values stated in SI units are to be regarded as standard.  
1.3 ACSS/TW is designed to increase the aluminum area for a given diameter of conductor by the use of trapezoidal shaped wires (TW), or to reduce the diameter for a given area of aluminum. The conductors consist of a central core of round steel wire(s) surrounded by two or more layers of trapezoidal aluminum 1350-0 wires. Different strandings of the same size of conductor are identified by type, which is the approximate ratio of steel area to aluminum area expressed in percent (see Table 1, Table 2 and Table 3). For the purpose of this specification, the sizes listed in Table 1 and Table 2 are tabulated on the basis of the finished conductor having an area or outside diameter equal to that of specified sizes of standard ACSR, ACSS, and ACSR/TW so as to facilitate conductor selection.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM B398/B398M-22(Specification)
Standard Specification for Aluminum-Alloy 6201-T81 and 6201-T83 Wire for Electrical Purposes

ABSTRACT
This specification covers aluminum-alloy 6201-T81 round wire which are solution heat-treated, cold worked, and artificially aged for electrical purposes. The material shall conform to the chemical composition requirements. Tensile properties such as tensile strength and elongation and bending properties shall be determined via a tension test and bending test, respectively. The electrical resistivity and density of the wires shall be measured as well.
SCOPE
1.1 This specification covers aluminum-alloy 6201-T81 (hard, solution heat-treated, cold worked, and artificially aged) and 6201-T83 (hard, higher conductivity, solution heat-treated, cold worked, and artificially aged) round wire for electrical purposes.
Note 1: The alloy and temper designations conform to ANSI H35.1 and H35.1M. Aluminum-alloy 6201 corresponds to unified numbering system alloy A96201 in accordance with Practice E527.  
1.2 The values stated in inch-pound or SI units are to be regarded separately as standard. The values in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.  
1.2.1 For density, resistivity and temperature, the values stated in SI units are to be regarded as standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM B856-22(Specification)
Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Coated Steel Supported (ACSS)

ABSTRACT
This specification covers round wire concentric-lay-stranded aluminium conductors, steel supported (ACSS) for use as ovehead electrical conductors. Tests for mechanical and electrical properties of aluminum wires shall be made after stranding. The electrical resistivity shall meet the minimum resistivity specified for the wire after stranding.
SCOPE
1.1 This specification covers round wire concentric-lay-stranded aluminum conductors, steel supported (ACSS) for use as overhead electrical conductors (see Explanatory Note 1).  
1.2 The values stated in inch-pound or SI units are to be regarded separately as standard. Each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. For conductor sizes designated by AWG or kcmil sizes, the requirements in SI units are numerically converted from the corresponding requirements in inch-pound units. For conductor sizes designation by AWG or kcmil, the requirements in SI units have been numerically converted from corresponding values stated or derived in inch-pound units. For conductor sizes designated by SI units only, the requirements are stated or derived in SI units.  
1.2.1 For density, resistivity and temperature, the values stated in SI units are to be regarded as standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
  • Technical specification
    8 pages
    English language
    sale 15% off