ASTM F964-09
(Specification)Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Exterior Profiles Used for Fencing and Railing
Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Exterior Profiles Used for Fencing and Railing
ABSTRACT
This specification deals with rigid poly vinyl-chloride (PVC) exterior profiles used for agricultural, commercial, residential fencing and railing. The material used in these exterior profiles is limited to rigid poly (vinyl chloride) (PVC) compounds in a single homogeneous extrusion or in a coextrusion of two or more PVC compounds in distinct layers. Loadbearing characteristics for fence and railing assemblies are not addressed within this specification (for example, windload, horizontal or vertical guardrail loading). Materials shall be tested and shall conform to requirements for the material properties and physical properties, including dimensional tolerances, extrusion quality, and weatherability. Methods for testing and for identifying exterior profile extrusions, such as impact resistance, warp, dimensional stability, and impact test on weathered specimen that comply with this specification are also provided.
SIGNIFICANCE AND USE
The purpose of this specification is to establish a recognized standard of quality for rigid poly vinyl chloride (PVC) exterior profiles for use in assembling agricultural, commercial, and residential fencing and railing. The term “PVC fence” refers to complete fencing and railings systems in which the primary structural members such as posts, rails, spindles, pickets, and gates are made from PVC exterior profiles. Accessory components (not included in this specification), including bolts, screws, hinges, latches, caps, and brackets, may be made from PVC and/or non-PVC materials. The information contained in this specification is intended to be helpful to producers, distributors, and users and to promote understanding between purchasers and sellers.
SCOPE
1.1 This specification establishes requirements for the material properties and physical properties, including dimensional tolerances, extrusion quality, and weatherability, of rigid poly vinyl-chloride (PVC) exterior profiles used for agricultural, commercial, residential fencing and railing. Methods for testing and for identifying exterior profile extrusions that comply with this specification are also provided.
Note 1—Information with regard to application, assembly, and installation should be obtained from the manufacturer and/or in accordance with Practice F 1999.
Note 2—Loadbearing characteristics for fence and railing assemblies are not addressed within this specification (for example, windload, horizontal or vertical guardrail loading).
1.2 The material used in these exterior profiles is limited to rigid poly (vinyl chloride) (PVC) compounds in a single homogeneous extrusion or in a coextrusion of two or more PVC compounds in distinct layers.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are provided for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F964 −09
StandardSpecification for
Rigid Poly (Vinyl Chloride) (PVC) Exterior Profiles Used for
1
Fencing and Railing
ThisstandardisissuedunderthefixeddesignationF964;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D696TestMethodforCoefficientofLinearThermalExpan-
sion of Plastics Between −30°C and 30°C with a Vitreous
1.1 This specification establishes requirements for the ma-
Silica Dilatometer
terialpropertiesandphysicalproperties,includingdimensional
D883Terminology Relating to Plastics
tolerances, extrusion quality, and weatherability, of rigid poly
D1435Practice for Outdoor Weathering of Plastics
vinyl-chloride (PVC) exterior profiles used for agricultural,
D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
commercial, residential fencing and railing. Methods for test-
tics
ing and for identifying exterior profile extrusions that comply
D1784Specification for Rigid Poly(Vinyl Chloride) (PVC)
with this specification are also provided.
Compounds and Chlorinated Poly(Vinyl Chloride)
NOTE 1—Information with regard to application, assembly, and instal-
(CPVC) Compounds
lationshouldbeobtainedfromthemanufacturerand/orinaccordancewith
3
D1898Practice for Sampling of Plastics (Withdrawn 1998)
Practice F1999.
D2244Practice for Calculation of Color Tolerances and
NOTE 2—Loadbearing characteristics for fence and railing assemblies
Color Differences from Instrumentally Measured Color
are not addressed within this specification (for example, windload,
horizontal or vertical guardrail loading).
Coordinates
D2565Practice for Xenon-Arc Exposure of Plastics In-
1.2 The material used in these exterior profiles is limited to
tended for Outdoor Applications
rigid poly (vinyl chloride) (PVC) compounds in a single
D4216Specification for Rigid Poly(Vinyl Chloride) (PVC)
homogeneous extrusion or in a coextrusion of two or more
and Related PVC and Chlorinated Poly(Vinyl Chloride)
PVC compounds in distinct layers.
(CPVC) Building Products Compounds
1.3 The values stated in inch-pound units are to be regarded
D4226Test Methods for Impact Resistance of Rigid Poly-
as the standard. The values in parentheses are provided for
(Vinyl Chloride) (PVC) Building Products
information only.
D4726Specification for Rigid Poly(Vinyl Chloride) (PVC)
1.4 This standard does not purport to address all of the
Exterior-Profile Extrusions Used forAssembled Windows
safety concerns, if any, associated with its use. It is the
and Doors
responsibility of the user of this standard to establish appro-
F1999Practice for Installation of Rigid Poly(Vinyl Chlo-
priate safety and health practices and determine the applica-
ride) (PVC) Fence Systems
bility of regulatory limitations prior to use.
G154PracticeforOperatingFluorescentLightApparatusfor
UV Exposure of Nonmetallic Materials
2. Referenced Documents
2 3. Terminology
2.1 ASTM Standards:
D618Practice for Conditioning Plastics for Testing
3.1 General—DefinitionsareinaccordancewithTerminolo-
D635Test Method for Rate of Burning and/or Extent and gies D883 and D1600, unless otherwise indicated.
Time of Burning of Plastics in a Horizontal Position
3.2 Definitions of Terms Specific to This Standard:
3.2.1 capstock—the outer layer in a coextrusion exposed to
weathering.
1
This specification is under the jurisdiction ofASTM Committee F14 on Fences
and is the direct responsibility of Subcommittee F14.30 on Rigid Polymer Fence 3.2.2 coextrusion—the process of coextruding profiles from
Systems.
two or more concentric streams of PVC compounds.
Current edition approved July 1, 2009. Published August 2009. Originally
approved in 1994. Last previous edition approved in 2008 as F964-08. DOI:
10.1520/F0964-09.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F964−09
NOTE 3—Separate PVC materials may be coextruded to form a
5.5 The PVC compound, when tested in accordance with
multi-layered profile with each layer having different physical character-
Test Method D635, shall not exceed an average extent of burn
istics such as strength and weathering.
of 4 in. (100 mm), with an average time of burn not to exceed
3.2.3 reworked material—material from the manufacturer’s
10 s.Asample thickness of 0
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:F 964–08 Designation: F 964 – 09
Standard Specification for
Rigid Poly (Vinyl Chloride) (PVC) Exterior Profiles Used for
1
Fencing and Railing
This standard is issued under the fixed designation F 964; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification establishes requirements for the material properties and physical properties, including dimensional
tolerances, extrusion quality, and weatherability, of rigid poly vinyl-chloride (PVC) exterior profiles used for agricultural,
commercial, residential fencing and railing. Methods for testing and for identifying exterior profile extrusions that comply with
this specification are also provided.
NOTE 1—Information with regard to application, assembly, and installation should be obtained from the manufacturer and/or in accordance with
Practice F1999.
NOTE 2—Loadbearing characteristics for fence and railing assemblies are not addressed within this specification (for example, windload, horizontal
or vertical guardrail loading).
1.2 The material used in these exterior profiles is limited to rigid poly (vinyl chloride) (PVC) compounds in a single
homogeneous extrusion or in a coextrusion of two or more PVC compounds in distinct layers.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are provided for
information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D635 Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position
D696 Test Method for Coefficient of Linear Thermal Expansion of Plastics Between 30C and 30C with a Vitreous Silica
Dilatometer
D883 Terminology Relating to Plastics
D1435 Practice for Outdoor Weathering of Plastics
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds
3
D1898 Practice for Sampling of Plastics
D2244 Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
D2565 Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications
D4216 Specification for Rigid Poly(Vinyl Chloride) (PVC) and Related PVC and Chlorinated Poly(Vinyl Chloride) (CPVC)
Building Products Compounds
D4226 Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products
D4726
D4726 Specification for Rigid Poly(Vinyl Chloride) (PVC) Exterior-Profile Extrusions Used for Assembled Windows and
Doors
1
ThisspecificationisunderthejurisdictionofASTMCommitteeF14onFencesandisthedirectresponsibilityofSubcommitteeF14.30onRigidPolymerFenceSystems.
Current edition approved Feb.July 1, 2008.2009. Published February 2008.August 2009. Originally approved in 1994. Last previous edition approved in 20022008 as
F964-028.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Withdrawn
3
Withdrawn. The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F 964–09
F1999 Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Fence Systems
G154 Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials
3. Terminology
3.1 General—Definitions are in accordance with Terminologies D883 and D1600 and D1600, unless otherwise indicated.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 capstock—the outer layer in a coextrusion exposed to weathering.
3.2.2 coextrusion—the process of coextruding profiles from two or more concentric streams of PVC compounds.
2
---------------------- Page: 2 ----------------------
F 964–09
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.