ASTM F1999-14(2019)
(Practice)Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Fence Systems
Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Fence Systems
ABSTRACT
This practice covers the minimum requirement for and methods of installation for rigid poly(vinyl chloride) (PVC) fencing systems and fence accessories, it is intended to guide those responsible for or concerned with installation of rigid (PVC) fence systems. The procedure for installation of posts, installation of rails and section, installation of post caps and picket tops, and installation of gates on posts are presented in details.
SCOPE
1.1 This practice covers the minimum requirement for and methods of installation for rigid poly(vinyl chloride) (PVC) fencing systems and fence accessories in areas where the maximum frost penetration does not exceed 30 in. [76 cm]. In all cases, refer also to the specific manufacturer's instructions for installation.
1.2 This practice is intended to guide those responsible for or concerned with installation of rigid (PVC) fence systems.
1.3 This practice does not preclude any test method that is proven to give equal or better performance under any weather, soil, or frost conditions.
1.4 End-use and applicable code requirements shall be considered in the choice of fence style, spacing, height, and installation method.
1.4.1 Paddock fencing for livestock may need to be more durable than perimeter fence.
1.4.2 Residential fence styles may not be designed for balcony or guardrail use.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in brackets are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F1999 −14 (Reapproved 2019)
Standard Practice for
Installation of Rigid Poly(Vinyl Chloride) (PVC) Fence
Systems
This standard is issued under the fixed designation F1999; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2.1 ASTM Standards:
1.1 This practice covers the minimum requirement for and
A706/A706M Specification for Deformed and Plain Low-
methods of installation for rigid poly(vinyl chloride) (PVC)
Alloy Steel Bars for Concrete Reinforcement
fencing systems and fence accessories in areas where the
D2564 Specification for Solvent Cements for Poly(Vinyl
maximum frost penetration does not exceed 30 in. [76 cm]. In
Chloride) (PVC) Plastic Piping Systems
all cases, refer also to the specific manufacturer’s instructions
F964 Specification for Rigid Poly (Vinyl Chloride) (PVC)
for installation.
Exterior Profiles Used for Fencing and Railing
1.2 This practice is intended to guide those responsible for
or concerned with installation of rigid (PVC) fence systems.
3. Terminology
1.3 This practice does not preclude any test method that is
3.1 Definitions of Terms Specific to This Standard:
proven to give equal or better performance under any weather,
3.1.1 clip—a component used to lock rails into routed posts.
soil, or frost conditions.
3.1.2 corner post—a post that accepts fence rails so that a
1.4 End-use and applicable code requirements shall be
fence ends in one direction and starts in another, more or less,
considered in the choice of fence style, spacing, height, and
perpendicular direction.
installation method.
3.1.3 end cap—a component to cover the open end of a rail
1.4.1 Paddock fencing for livestock may need to be more
or other extrusion.
durable than perimeter fence.
3.1.4 end post—the end or last vertical structural support
1.4.2 Residential fence styles may not be designed for
member of the fence.
balcony or guardrail use.
3.1.5 exterior profile—a rigid poly(vinyl chloride) (PVC)
1.5 The values stated in inch-pound units are to be regarded
extrusion that conforms to Specification F964.
as standard. The values given in brackets are for information
3.1.6 gate—a hinged panel for passage into or out of a
only.
fenced area.
1.6 This standard does not purport to address all of the
3.1.7 hinge post—the post to which a gate is attached.
safety concerns, if any, associated with its use. It is the
3.1.8 notch—a method of creating a tab used to lock rails
responsibility of the user of this standard to establish appro-
into routed posts.
priate safety, health, and environmental practices and deter-
mine the applicability of regulatory limitations prior to use.
3.1.9 outside brackets—components used to fasten rails to
1.7 This international standard was developed in accor-
the outside of posts, when routed posts are not used.
dance with internationally recognized principles on standard-
3.1.10 picket—a vertical member in a fence panel, between
ization established in the Decision on Principles for the
or attached to the horizontal members.
Development of International Standards, Guides and Recom-
3.1.11 picket cap—a component used to cover or decorate
mendations issued by the World Trade Organization Technical
the open end(s) of picket.
Barriers to Trade (TBT) Committee.
3.1.12 post cap—a component used to cover the top of a
post.
This practice is under the jurisdiction ofASTM Committee F14 on Fences and
is the direct responsibility of Subcommittee F14.30 on Rigid Polymer Fence
Systems. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Oct. 1, 2019. Published October 2019. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2000. Last previous edition approved in 2014 as F1999 – 14. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F1999-14R19. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F1999 − 14 (2019)
3.1.13 posts—the vertical structural support members of the [609 mm] plus an additional 3 in. [76 mm] for each 1-ft
fence. [305-mm] increased fence height over 4 ft [1.22 m].
7.1.2 In areas where frost is common, the footing shall
3.1.14 rails—the horizontal members which insert into or
extend a minimum of 6 in. [152.4 mm] below the maximum
attach to the posts. They serve as the sole sections between
frost level.
posts or as back rails to which picket verticals are attached.
7.2 Preparation of Post—To secure post vertically, provide
3.1.15 routed posts—posts with holes cut into them to allow
a means such as, but not limited to, notching, drilling,
rails to be inserted.
roughing, pinning, etc.
4. Materials
7.3 Installation of Posts—This practice includes post setting
4.1 Exterior Profiles, in accordance with Specification
methods. Careful consideration should be taken to choose the
F964.
correct method based on soil types at the installation location.
7.3.1 Method 1—Partially fill holes with concrete, then set
4.2 Solvent Cement— Poly(Vinyl Chloride) (PVC) solvent
the post into the concrete leaving approximately 2 to 4 in. [51
cement in accordance with Specification D2564.
to 101 mm] of concrete below the bottom of the post (see Fig.
4.3 Reinforcing Steel Rods,inaccordancewithSpecification
1). Continue filling the hole with concrete to within 6 to 9 in.
A706/A706M low-alloy steel deformed bars for concrete
[152.4 to 228.6 mm] of the top. Fill the remainder of the hole
reinforcement.
with soil or fine rocks. Where frost is not likely, the hole may
be filled to ground level with concrete (see Note 1). The post
5. Protection of Material in Transportation and Storage
shall extend a minimum of 18 in. [457.2 mm] into the concrete
5.1 Exterior profiles shall be supported in a manner that will
(see Fig. 2). Check to see that the post remains plumb until the
prevent sagging, twisting, or bending. Fence products shall be
concrete has set.
stored in a manner that prevents accumulation
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.