ASTM B676-03(2014)
(Specification)Standard Specification for UNS N08367 Welded Tube
Standard Specification for UNS N08367 Welded Tube
ABSTRACT
The specification covers UNS N08367 welded tube of limited diameter and thickness for general corrosion applications. The tube shall be manufactured from flat-rolled alloy by an automatic welding process with no additional filer metal. The tube shall be furnished with oxide removed. The material shall composed of carbon, manganese, silicon, phosphorus, sulfur, chromium, nickel, molybdenum, nitrogen, iron, and copper. The tube shall be subjected to the following tests: hydrostatic, pneumatic, eddy current, or ultrasonic test. The material shall also undergo tensile, flattening, flange, reverse-bend, and nondestructive test requirements. Reverse-bend test is not applicable for a specified wall size with respect to outside tube diameter. Nondestructive test includes pressure testing or electric testing. Test results shall show no evidence of cracking or flaws.
SCOPE
1.1 This specification covers UNS N083672 welded tube for general corrosion applications.
1.2 This specification covers outside diameter and nominal wall tube.
1.2.1 The tube sizes covered by this specification are 1/8 to 5 in. (3.2 to 127 mm) in outside diameter and 0.015 to 0.320 in. (0.38 to 8.13 mm), inclusive, in wall thickness.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B676 −03 (Reapproved 2014)
Standard Specification for
UNS N08367 Welded Tube
This standard is issued under the fixed designation B676; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Terminology
1.1 This specification covers UNS N08367 welded tube for 3.1 Terms defined in Terminology B899 shall apply unless
general corrosion applications. otherwise defined in this standard.
1.2 This specification covers outside diameter and nominal
4. General Requirement
wall tube.
1.2.1 The tube sizes covered by this specification are ⁄8 to 5 4.1 Material furnished in accordance with this specification
in. (3.2 to 127 mm) in outside diameter and 0.015 to 0.320 in. shall conform to the applicable requirements of Specification
(0.38 to 8.13 mm), inclusive, in wall thickness. B751 unless otherwise provided herein.
1.3 The values stated in inch-pound units are to be regarded
5. Classification
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only 5.1 Class 1—Welded, cold worked, solution treated, and
and are not considered standard.
each piece of each lot subjected to one of the following four
tests: hydrostatic, pneumatic (air underwater), eddy current, or
1.4 This standard does not purport to address all of the
ultrasonic.
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to become familiar
5.2 Class 2—Welded, cold worked, solution treated, and
with all hazards including those identified in the appropriate
each piece of each lot leak tested (hydrostatic or pneumatic)
Material Safety Data Sheet (MSDS) for this product/material
plus electric tested (eddy current or ultrasonic).
as provided by the manufacturer, to establish appropriate
safety and health practices, and determine the applicability of
6. Ordering Information
regulatory limitations prior to use.
6.1 It is the responsibility of the purchaser to specify all
requirements that are necessary for material ordered under this
2. Referenced Documents
specification. Examples of such requirements include, but are
2.1 ASTM Standards:
not limited to, the following:
A1016/A1016M Specification for General Requirements for
6.1.1 Alloy name or UNS number,
Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless
6.1.2 ASTM designation and year of issue,
Steel Tubes
6.1.3 Dimensions:
B751 Specification for General Requirements for Nickel and
6.1.3.1 Outside diameter and nominal wall thicknesses,
Nickel Alloy Welded Tube
B899 Terminology Relating to Non-ferrous Metals and Al-
NOTE 1—Tube produced to outside diameter and minimum wall
loys
thicknessmaybefurnisheduponagreementbetweenthemanufacturerand
the purchaser.
6.1.3.2 Length (specific or random),
This specification is under the jurisdiction of ASTM Committee B02 on
6.1.4 Class (Section 5),
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
6.1.5 Quantity (feet or number of pieces),
B02.07 on Refined Nickel and Cobalt and Their Alloys.
Current edition approved Oct. 1, 2014. Published October 2014. Originally 6.1.6 Certification—State if certification is required,
approved in 1980. Last previous edition approved in 2009 as B676 – 03 (2009).
6.1.7 Samples for Product (Check) Analysis—State whether
DOI: 10.1520/B0676-03R14.
2 samples for product (check) analysis should be furnished, and
New designation established in accordance with Practice E527 and SAE J1086,
Practice for Numbering Metals and Alloys (UNS).
6.1.8 Purchaser Inspection—If the purchaser wishes to
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
witness tests or inspection of material at the place of
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
manufacture, the purchase order must so state indicating which
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. tests or inspections are to be witnessed.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
B676−03 (2014)
7. Material and Manufacture 9. Mechanical Properties and Other Requirements
7.1 Tube shall be made from flat-rolled al
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B676 − 03 (Reapproved 2009) B676 − 03 (Reapproved 2014)
Standard Specification for
UNS N08367 Welded Tube
This standard is issued under the fixed designation B676; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*Scope
1.1 This specification covers UNS N08367*N08367 welded tube for general corrosion applications.
1.2 This specification covers outside diameter and nominal wall tube.
1.2.1 The tube sizes covered by this specification are ⁄8 to 5 in. (3.2 to 127 mm) in outside diameter and 0.015 to 0.320 in. (0.38
to 8.13 mm), inclusive, in wall thickness.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2.1 ASTM Standards:
A1016/A1016M Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel
Tubes
B751 Specification for General Requirements for Nickel and Nickel Alloy Welded Tube
B899 Terminology Relating to Non-ferrous Metals and Alloys
3. Terminology
3.1 Terms defined in Terminology B899 shall apply unless otherwise defined in this standard.
4. General Requirement
4.1 Material furnished in accordance with this specification shall conform to the applicable requirements of Specification B751
unless otherwise provided herein.
5. Classification
5.1 Class 1—Welded, cold worked, solution treated, and each piece of each lot subjected to one of the following four tests:
hydrostatic, pneumatic (air underwater), eddy current, or ultrasonic.
5.2 Class 2—Welded, cold worked, solution treated, and each piece of each lot leak tested (hydrostatic or pneumatic) plus
electric tested (eddy current or ultrasonic).
6. Ordering Information
6.1 It is the responsibility of the purchaser to specify all requirements that are necessary for material ordered under this
specification. Examples of such requirements include, but are not limited to, the following:
This specification is under the jurisdiction of ASTM Committee B02 on Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee B02.07 on Refined
Nickel and Cobalt and Their Alloys.
Current edition approved April 15, 2009Oct. 1, 2014. Published April 2009October 2014. Originally approved in 1980. Last previous edition approved in 20032009 as
B676 – 03.B676 – 03 (2009). DOI: 10.1520/B0676-03R09.10.1520/B0676-03R14.
*New designation established in accordance with Practice E527 and SAE J1086, Practice for Numbering Metals and Alloys (UNS).
New designation established in accordance with Practice E527 and SAE J1086, Practice for Numbering Metals and Alloys (UNS).
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
B676 − 03 (2014)
6.1.1 Alloy name or UNS number,
6.1.2 ASTM designation and year of issue,
6.1.3 Dimensions:
6.1.3.1 Outside diameter and nominal wall thicknesses,
NOTE 1—Tube produced to outside diameter and minimum wall thickness may be furnished upon agreement between the manufacturer and the
purchaser.
6.1.3.2 Length (specific or random),
6.1.4 Class (Section 5),
6.1.5 Quantity (feet or number of pieces),
6.1.6 Certification—State if certification is required,
6.1.7 Samples for Product (Check) Analysis—State whether samples for product (check) analysis should be furnished, and
6.1.8 Purchaser Inspection—If the purchaser wishes to witness tests or inspection of material at the place of manufacture, the
purchase order must so state indicating which tests or
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.