ASTM F2509-24
(Specification)Standard Specification for Field-assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene and Polyamide-11 (PA11) Gas Distribution Pipe and Tubing
Standard Specification for Field-assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene and Polyamide-11 (PA11) Gas Distribution Pipe and Tubing
ABSTRACT
This specification covers the qualification requirements and test methods for field-assembled anodeless riser kits for use with outside diameter controlled polyethylene gas distribution pipes and tubing in sizes of up to 2 IPS. The anodeless riser kits shall be manufactured in accordance with the specified materials, physical properties, and design, which include the riser casings, moisture seals, threads, bend radius, coatings, welding procedures, and riser adapter to riser casing connections. The riser adapter to riser casing connections shall tested by tensile pull testing.
SCOPE
1.1 This specification covers requirements and test methods for field-assembled anodeless riser kits for use with outside diameter controlled polyethylene and PA11 gas distribution pipe and tubing in sizes through 2 IPS as specified in Specification D2513 polyethylene and Specification F2945 for PA11.
1.2 The test methods described are not intended to be routine quality control tests.
1.3 This specification covers the types of field-assembled anodeless riser kits described in 3.3.2.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and not considered standard.
1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures), shall not be considered as requirements of the standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F2509 − 24 An American National Standard
Standard Specification for
Field-assembled Anodeless Riser Kits for Use on Outside
Diameter Controlled Polyethylene and Polyamide-11 (PA11)
1
Gas Distribution Pipe and Tubing
This standard is issued under the fixed designation F2509; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
1.1 This specification covers requirements and test methods 2.1 ASTM Standards:
for field-assembled anodeless riser kits for use with outside A513/A513M Specification for Electric-Resistance-Welded
diameter controlled polyethylene and PA11 gas distribution Carbon and Alloy Steel Mechanical Tubing
pipe and tubing in sizes through 2 IPS as specified in A53/A53M Specification for Pipe, Steel, Black and Hot-
Specification D2513 polyethylene and Specification F2945 for Dipped, Zinc-Coated, Welded and Seamless
PA11. D638 Test Method for Tensile Properties of Plastics
D1600 Terminology for Abbreviated Terms Relating to Plas-
1.2 The test methods described are not intended to be
3
tics (Withdrawn 2024)
routine quality control tests.
D2513 Specification for Polyethylene (PE) Gas Pressure
1.3 This specification covers the types of field-assembled
Pipe, Tubing, and Fittings
anodeless riser kits described in 3.3.2.
F412 Terminology Relating to Plastic Piping Systems
1.4 The values stated in inch-pound units are to be regarded F1948 Specification for Metallic Mechanical Fittings for
Use on Outside Diameter Controlled Thermoplastic Gas
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only Distribution Pipe and Tubing
F2897 Specification for Tracking and Traceability Encoding
and not considered standard.
System of Natural Gas Distribution Components (Pipe,
1.5 The text of this standard references notes and footnotes
Tubing, Fittings, Valves, and Appurtenances)
which provide explanatory material. These notes and footnotes
F2945 Specification for Polyamide 11 Gas Pressure Pipe,
(excluding those in tables and figures), shall not be considered
Tubing, and Fittings
as requirements of the standard.
4
2.2 ASME Standards:
1.6 This standard does not purport to address all of the 4
ASME Boiler and Pressure Vessel Code
safety concerns, if any, associated with its use. It is the 5
ASME B1.20.1 Pipe Threads, General Purpose (Inch)
responsibility of the user of this standard to establish appro-
B31.8 Gas Transmission and Distribution Piping Systems
priate safety, health, and environmental practices and deter- 5
2.3 Federal Regulations:
mine the applicability of regulatory limitations prior to use.
United States CFR, Title 49, Part 192 Pipeline Safety
1.7 This international standard was developed in accor-
Regulations
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Development of International Standards, Guides and Recom-
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
mendations issued by the World Trade Organization Technical
Standards volume information, refer to the standard’s Document Summary page on
Barriers to Trade (TBT) Committee. the ASTM website.
3
The last approved version of this historical standard is referenced on
www.astm.org.
4
Available from American Society of Mechanical Engineers (ASME), ASME
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
Piping Systems and is the direct responsibility of Subcommittee F17.60 on Gas. www.asme.org.
5
Current edition approved April 1, 2024. Published April 2024. Originally Available from U.S. Government Printing Office, Superintendent of
approved in 2006. Last previous edition approved in 2019 as F2509 – 15(2019). Documents, 732 N. Capitol St., NW, Washington, DC 20401-0001, http://
DOI: 10.1520/F2509-24. www.access.gpo.gov.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2509 − 24
6
2.4 UL Standard: Alternate materials proven to provide equal or better perfor-
UL 360 Standard for Liquid-Tight Flexible Steel Conduit mance shall be acce
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2509 − 15 (Reapproved 2019) F2509 − 24 An American National Standard
Standard Specification for
Field-assembled Anodeless Riser Kits for Use on Outside
Diameter Controlled Polyethylene and Polyamide-11 (PA11)
1
Gas Distribution Pipe and Tubing
This standard is issued under the fixed designation F2509; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This specification covers requirements and test methods for field-assembled anodeless riser kits for use with outside diameter
controlled polyethylene and PA11 gas distribution pipe and tubing in sizes through 2 IPS as specified in Specification D2513
polyethylene and Specification F2945 for PA11.
1.2 The test methods described are not intended to be routine quality control tests.
1.3 This specification covers the types of field-assembled anodeless riser kits described in 3.3.2.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and not considered standard.
1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes
(excluding those in tables and figures), shall not be considered as requirements of the standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A513/A513M Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing
A53/A53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
D638 Test Method for Tensile Properties of Plastics
3
D1600 Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.60 on Gas.
Current edition approved Aug. 1, 2019April 1, 2024. Published August 2019April 2024. Originally approved in 2006. Last previous edition approved in 20152019 as
F2509 – 15.F2509 – 15(2019). DOI: 10.1520/F2509-15R19.10.1520/F2509-24.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2509 − 24
D2513 Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
F412 Terminology Relating to Plastic Piping Systems
F1948 Specification for Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas Distribution
Pipe and Tubing
F2897 Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing,
Fittings, Valves, and Appurtenances)
F2945 Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings
4
2.2 ASME Standards:
4
ASME Boiler and Pressure Vessel Code
5
ASME B1.20.1 Pipe Threads, General Purpose (Inch)
B31.8 Gas Transmission and Distribution Piping Systems
5
2.3 Federal Regulations:
United States CFR, Title 49, Part 192 Pipeline Safety Regulations
6
2.4 UL Standard:
UL 360 Standard for Liquid-Tight Flexible Steel Conduit
3. Terminology
3.1 The gas industry terminology used in this specification is in accordance with ASME B31.8 or the United States CFR, Title
49, Part 192, unless otherwise indicated.
3.1.1 pipe—used her
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.